Претраживање
Приказ резултата 1-10 од 10
Structural analysis of Zn2TiO4 doped with MgO
(Springer, 2009)
The starting mixtures of ZnO, TiO2, and MgO (0, 1.25, and 2.5 wt.%) powders are mechanically activated in a high-energy planetary mill for 15 min and then sintered between 800 and 1100°C for 2 h. The influence of MgO ...
The master sintering curves for BaTi0.975Sn0.025O3/BaTi0.85S n0.15O3 functionally graded materials
(Elsevier, 2009)
The most important aim in the design and processing of functionally graded materials (FGMs) is to produce devices free from any deformation. Smart choices of different combination of graded layers, as well as the heating ...
Influence of mechanical activation on structural and electrical properties of sintered MgTiO3 ceramics
(Belgrade : International Institute for the Science of Sintering, 2009)
The aim of this work was to analyze the influence of mechanical activation on the MgCO3-TiO2 system. Mixtures of MgCO3-TiO2 were mechanically activated for 15, 30, 60 and 120 minutes in a planetary ball mill and after that ...
Phase Formation at the Sintering of Sa, Zn, Ti Oxides
(Kiev, 2009)
Complex compounds with oxide phases of Ba, 2n, and 11 are widely used in instrument engineering. It is also important to find such production routes for ceramics, which provide their stable structure and properties. Phase ...
Densification rate and phase structure changes during sintering of zinc titanate ceramics
(Elsevier, 2009)
Densification rate and phase structure changes during sintering of nanosized ZnTiO3 were studied. Sintering was performed in a dilatometer in two regimes: the first to 900 °C (heating rates 5, 10 and 15 °C/min) and the ...
Influence of MgO addition on the synthesis and electrical properties of sintered zinc-titanate ceramics
(Elsevier, 2009)
Starting mixtures of ZnO, TiO2 and MgO (0, 1.25 and 2.5 wt.% MgO) powders were mechanically activated for 15 min in a planetary ball mill. The powders obtained were sintered non-isothermally to temperatures between 800 and ...
Surface analysis of bismuth titanate by Auger and X-ray photoelectron spectroscopy
(Elsevier, 2009)
The Auger and XPS technique has been used for investigation in the surface of bismuth titanate (Bi4Ti3O12) (BIT) ceramics obtained by reactive sintering from Bi2O3 and TiO2 oxides. All peaks characteristic for bismuth, ...
Densification, Microstructure, and Electrical Properties of BaTiO3 (BT) Ceramics Prepared from Ultrasonically De-Agglomerated BT Powders
(Taylor & Francis, 2009)
In this study, a correlation between densification, microstructure, and electrical properties of BaTiO3 (BT) ceramics prepared from ultrasonically de-agglomerated BT powders has been analyzed. BT powders with the same ...
Structural and electrical properties of sintered zinc-titanate ceramics
(Elsevier, 2009)
The aim of this work was an investigation of structural and electrical properties of sintered zinc-titanate ceramics obtained by mechanical activation. Mixtures of ZnO and TiO2 were mechanically activated in a planetary ...
BaTi0.975Sn0.025O3/BaTi0.85Sn0.15O3 functionally graded materials: master sintering curves and electrical properties
(Belgrade : Institute of Technical Sciences of SASA, 2009)
The most important aim in the design and processing of functionally graded materials (FGMs) is to obtain high-quality microstructure, and to produce devices free from any form of deformation. During sintering of BTS2.5/BTS15 ...