Претраживање
Приказ резултата 1-10 од 14
Structural analysis of Zn2TiO4 doped with MgO
(Springer, 2009)
The starting mixtures of ZnO, TiO2, and MgO (0, 1.25, and 2.5 wt.%) powders are mechanically activated in a high-energy planetary mill for 15 min and then sintered between 800 and 1100°C for 2 h. The influence of MgO ...
The master sintering curves for BaTi0.975Sn0.025O3/BaTi0.85S n0.15O3 functionally graded materials
(Elsevier, 2009)
The most important aim in the design and processing of functionally graded materials (FGMs) is to produce devices free from any deformation. Smart choices of different combination of graded layers, as well as the heating ...
Densification rate and phase structure changes during sintering of zinc titanate ceramics
(Elsevier, 2009)
Densification rate and phase structure changes during sintering of nanosized ZnTiO3 were studied. Sintering was performed in a dilatometer in two regimes: the first to 900 °C (heating rates 5, 10 and 15 °C/min) and the ...
Influence of MgO addition on the synthesis and electrical properties of sintered zinc-titanate ceramics
(Elsevier, 2009)
Starting mixtures of ZnO, TiO2 and MgO (0, 1.25 and 2.5 wt.% MgO) powders were mechanically activated for 15 min in a planetary ball mill. The powders obtained were sintered non-isothermally to temperatures between 800 and ...
Surface analysis of bismuth titanate by Auger and X-ray photoelectron spectroscopy
(Elsevier, 2009)
The Auger and XPS technique has been used for investigation in the surface of bismuth titanate (Bi4Ti3O12) (BIT) ceramics obtained by reactive sintering from Bi2O3 and TiO2 oxides. All peaks characteristic for bismuth, ...
Preparation and properties of BaTi1-xSnxO3 multilayered ceramics
(Journal of the European Ceramic Society, 2007)
BaTi1-xSnxO3 (BTS) powders, with x ranging from 0 to 0.15, were synthesized by solid-state reaction technique. The powders were pressed and sintered at 1370 degrees C. Obtained BTS ceramics were investigated by X-ray ...
Far infrared reflection spectroscopy of Zn2SnO4 ceramics obtained by sintering mechanically activated ZnO-SnO2 powder mixtures
(Elsevier Sci Ltd, Oxford, 2007)
A mixture of starting ZnO and SnO2 powders (molar ratio 2: 1) were mechanically activated for 10, 40, 80 and 160 min in a planetary ball mill and then isothermally sintered at 1300 degrees C for 2 h in order to obtain ...
Microstructural evolution and electric properties of mechanically activated BaTiO3 ceramics
(Oxford : Elsevier Sci Ltd, 2007)
Ceramic materials with a perovskite related structures such as non-doped and doped barium titanate ceramics are attracting much interest for their application as capacitor dielectrics, resistors, thermal sensors, etc. Since ...
Densification, Microstructure, and Electrical Properties of BaTiO3 (BT) Ceramics Prepared from Ultrasonically De-Agglomerated BT Powders
(Taylor & Francis, 2009)
In this study, a correlation between densification, microstructure, and electrical properties of BaTiO3 (BT) ceramics prepared from ultrasonically de-agglomerated BT powders has been analyzed. BT powders with the same ...
Structural and electrical properties of sintered zinc-titanate ceramics
(Elsevier, 2009)
The aim of this work was an investigation of structural and electrical properties of sintered zinc-titanate ceramics obtained by mechanical activation. Mixtures of ZnO and TiO2 were mechanically activated in a planetary ...