Search
Now showing items 1-10 of 172
Analiza osetljivosti debeloslojnih NTC termistora na promene temperature i protoka vazduha
(Čačak : University of Kragujevac, Faculty of Technical Sciences, 2006)
NTC termistori na bazi Mn, Ni, Co i Fe oksida za potrebe debeloslojnih senzora pripadaju oblasti istraživačkog i primenjenog rada sa ciljem realizacije senzora prilagođenih po obliku, prenosu toplote i brzini odziva fizičkim ...
Sintering of fly ash based composites with zeolite and bentonite addition for application in construction materials
(International Institute for the Science of Sintering, 2017)
Due to pozzolanic characteristics, fly ash is commonly used as a cement replacement in construction composites. Addition of natural clays with sorption ability (i.e. zeolite and bentonite) in to the fly ash based construction ...
Kosanović, D., Blagojević, V.A., Maričić, A., Aleksić, S., Pavlović, V.P., Pavlović, V.B., Vlahović, B., 2018. Influence of mechanical activation on functional properties of barium hexaferrite ceramics. Ceramics International 44, 6666–6672. https://doi.org/10.1016/j.ceramint.2018.01.078: Supplement
(Ceramics International, 2018)
Rietveld analysis of XRD patterns of mechanically activated Fe:BaTiO3 powder mixtures sintered at 1200°C
Influence of nitrogen and air atmosphere during thermal treatment on micro and nano sized powders and sintered TiO2 specimens
(Belgrade : International Institute for the Science of Sintering, 2014)
The influence of air and nitrogen atmosphere during heating on TiO2 nano and micro sized powders as well as sintered polycrystalline specimens was analyzed. Sintering of TiO2 nano and micro powders in air atmosphere was ...
Statistical Analysis of the Influence of Temperature on Microstructure Contact Surfaces on BaTiO3 -ceramics Doped with Ho2O3
(Belgrade : Serbian Ceramic Society, 2014)
The materials based on BaTiO3 can be controlled using different technological parameters and different additives. We investigate the influence of different temperature levels of sintering (1320°C, 1350°C and 1380°C) on the ...
The Influence of Mechanical Activation on Sintering Process of BaCO3-SrCO3-TiO2 System
(Belgrade : Serbian Ceramic Society, 2012)
In this article the influence of mechanical activation on sintering process of barium-strontiumtitanate ceramics has been investigated. Both non-activated and mixtures treated in planetary ball mill for 5, 10, 20, 40, 80 ...
Synthesis, characterization and sintering properties of Zr-doped hydroxyapatite
(Belgrade : Institute of Technical Sciences of the Serbian Academy of Sciences and Arts, 2011)
Improving of material characteristics could be achieved in different ways, but it is always connected with the issue of impairing the other functional properties. Hydroxyapatite bioceramics lacks of insufficient mechanical ...
The influence of mechanical activation on sintering process of BaCO3-SrCO3-TiO2 system
(Belgrade : International Institute for the Science of Sintering, 2012)
In this article the influence of mechanical activation on sintering process of bariumstrontium-titanate ceramics has been investigated. Both non-activated and mixtures treated in a planetary ball mill for 5, 10, 20, 40, ...
Influence of Point Defects Concentration on Densification Process and Optical Properties of Sintered ZnO Ceramics
(Belgrade : Materials Research Society of Serbia, 2015)
Zinc oxide is one of the most studied materials due to its potential applications in electronics, optoelectronics and spintronics. In the forms of single crystal and thin-film ZnO could be used as UV and blue light emitter, ...
Shungite - a Russian mineral: possible application as a microwave absorber
(Belgrade : Materials Research Society of Serbia, 2018)
The paper presents results of investigation of the influence of mechanical activation of shungite, a Russian natural mineral rich in silica and carbon, on its sintering behavior. The mechanical activation of the starting ...