Ministry of Education, Science and Technological Development, Republic of Serbia, Grant no. 451-03-68/2020-14/200135 (University of Belgrade, Faculty of Technology and Metallurgy)

Link to this page

info:eu-repo/grantAgreement/MESTD/inst-2020/200135/RS//

Ministry of Education, Science and Technological Development, Republic of Serbia, Grant no. 451-03-68/2020-14/200135 (University of Belgrade, Faculty of Technology and Metallurgy) (en)
Ministarstvo prosvete, nauke i tehnološkog razvoja Republike Srbije, Ugovor br. 451-03-68/2020-14/200135 (Univerzitet u Beogradu, Tehnološko-metalurški fakultet) (sr_RS)
Министарство просвете, науке и технолошког развоја Републике Србије, Уговор бр. 451-03-68/2020-14/200135 (Универзитет у Београду, Технолошко-металуршки факултет) (sr)
Authors

Publications

Nanomechanical properties of PVDF–ZnO polymer nanocomposite

Peleš Tadić, Adriana; Blagojević, Vladimir A.; Stojanović, Dušica; Ostojić, Sanja B.; Tasić, Nikola; Kosanović, Darko; Uskoković, Petar; Pavlović, Vladimir B.

(Elsevier BV, 2023)

TY  - JOUR
AU  - Peleš Tadić, Adriana
AU  - Blagojević, Vladimir A.
AU  - Stojanović, Dušica
AU  - Ostojić, Sanja B.
AU  - Tasić, Nikola
AU  - Kosanović, Darko
AU  - Uskoković, Petar
AU  - Pavlović, Vladimir B.
PY  - 2023
UR  - https://dais.sanu.ac.rs/123456789/13560
AB  - Poly(vinylidenefluoride)–ZnO (PVDF–ZnO) nanocomposites with mechanically activated ZnO nanoparticle fillers were investigated using thermal and mechanical analysis and AFM and PFM. Differential scanning calorimetry (DSC) investigated the effect of ZnO nanoparticles on the crystallinity of the polymer, under controlled heating and cooling. Atomic force (AFM) microscopy was used to record the surfaces of the samples. Nanocomposite surface roughness shows the presence of the different phases inside of the matrix, where rough samples contain a higher proportion of the β phase. PFM was performed to investigate the piezoresponse of the composites. Nanoidentation showed that the mechanical activation of the filler (ZnO) increases the Young modulus with the activation time. Molecular simulations in periodic systems (PVDF–ZnO spherical nanocluster and nanocylinder composite) were used to investigate the influence of particle size and shape on the Young modulus of different phases of PVDF.
PB  - Elsevier BV
T2  - Materials Science and Engineering: B
T1  - Nanomechanical properties of PVDF–ZnO polymer nanocomposite
SP  - 116126
VL  - 287
DO  - 10.1016/j.mseb.2022.116126
UR  - https://hdl.handle.net/21.15107/rcub_dais_13436
ER  - 
@article{
author = "Peleš Tadić, Adriana and Blagojević, Vladimir A. and Stojanović, Dušica and Ostojić, Sanja B. and Tasić, Nikola and Kosanović, Darko and Uskoković, Petar and Pavlović, Vladimir B.",
year = "2023",
abstract = "Poly(vinylidenefluoride)–ZnO (PVDF–ZnO) nanocomposites with mechanically activated ZnO nanoparticle fillers were investigated using thermal and mechanical analysis and AFM and PFM. Differential scanning calorimetry (DSC) investigated the effect of ZnO nanoparticles on the crystallinity of the polymer, under controlled heating and cooling. Atomic force (AFM) microscopy was used to record the surfaces of the samples. Nanocomposite surface roughness shows the presence of the different phases inside of the matrix, where rough samples contain a higher proportion of the β phase. PFM was performed to investigate the piezoresponse of the composites. Nanoidentation showed that the mechanical activation of the filler (ZnO) increases the Young modulus with the activation time. Molecular simulations in periodic systems (PVDF–ZnO spherical nanocluster and nanocylinder composite) were used to investigate the influence of particle size and shape on the Young modulus of different phases of PVDF.",
publisher = "Elsevier BV",
journal = "Materials Science and Engineering: B",
title = "Nanomechanical properties of PVDF–ZnO polymer nanocomposite",
pages = "116126",
volume = "287",
doi = "10.1016/j.mseb.2022.116126",
url = "https://hdl.handle.net/21.15107/rcub_dais_13436"
}
Peleš Tadić, A., Blagojević, V. A., Stojanović, D., Ostojić, S. B., Tasić, N., Kosanović, D., Uskoković, P.,& Pavlović, V. B.. (2023). Nanomechanical properties of PVDF–ZnO polymer nanocomposite. in Materials Science and Engineering: B
Elsevier BV., 287, 116126.
https://doi.org/10.1016/j.mseb.2022.116126
https://hdl.handle.net/21.15107/rcub_dais_13436
Peleš Tadić A, Blagojević VA, Stojanović D, Ostojić SB, Tasić N, Kosanović D, Uskoković P, Pavlović VB. Nanomechanical properties of PVDF–ZnO polymer nanocomposite. in Materials Science and Engineering: B. 2023;287:116126.
doi:10.1016/j.mseb.2022.116126
https://hdl.handle.net/21.15107/rcub_dais_13436 .
Peleš Tadić, Adriana, Blagojević, Vladimir A., Stojanović, Dušica, Ostojić, Sanja B., Tasić, Nikola, Kosanović, Darko, Uskoković, Petar, Pavlović, Vladimir B., "Nanomechanical properties of PVDF–ZnO polymer nanocomposite" in Materials Science and Engineering: B, 287 (2023):116126,
https://doi.org/10.1016/j.mseb.2022.116126 .,
https://hdl.handle.net/21.15107/rcub_dais_13436 .

Nanomechanical properties of PVDF–ZnO polymer nanocomposite

Peleš Tadić, Adriana; Blagojević, Vladimir A.; Stojanović, Dušica; Ostojić, Sanja B.; Tasić, Nikola; Kosanović, Darko; Uskoković, Petar; Pavlović, Vladimir B.

(Elsevier BV, 2023)

TY  - JOUR
AU  - Peleš Tadić, Adriana
AU  - Blagojević, Vladimir A.
AU  - Stojanović, Dušica
AU  - Ostojić, Sanja B.
AU  - Tasić, Nikola
AU  - Kosanović, Darko
AU  - Uskoković, Petar
AU  - Pavlović, Vladimir B.
PY  - 2023
UR  - https://dais.sanu.ac.rs/123456789/13436
AB  - Poly(vinylidenefluoride)–ZnO (PVDF–ZnO) nanocomposites with mechanically activated ZnO nanoparticle fillers were investigated using thermal and mechanical analysis and AFM and PFM. Differential scanning calorimetry (DSC) investigated the effect of ZnO nanoparticles on the crystallinity of the polymer, under controlled heating and cooling. Atomic force (AFM) microscopy was used to record the surfaces of the samples. Nanocomposite surface roughness shows the presence of the different phases inside of the matrix, where rough samples contain a higher proportion of the β phase. PFM was performed to investigate the piezoresponse of the composites. Nanoidentation showed that the mechanical activation of the filler (ZnO) increases the Young modulus with the activation time. Molecular simulations in periodic systems (PVDF–ZnO spherical nanocluster and nanocylinder composite) were used to investigate the influence of particle size and shape on the Young modulus of different phases of PVDF.
PB  - Elsevier BV
T2  - Materials Science and Engineering: B
T1  - Nanomechanical properties of PVDF–ZnO polymer nanocomposite
SP  - 116126
VL  - 287
DO  - 10.1016/j.mseb.2022.116126
UR  - https://hdl.handle.net/21.15107/rcub_dais_13436
ER  - 
@article{
author = "Peleš Tadić, Adriana and Blagojević, Vladimir A. and Stojanović, Dušica and Ostojić, Sanja B. and Tasić, Nikola and Kosanović, Darko and Uskoković, Petar and Pavlović, Vladimir B.",
year = "2023",
abstract = "Poly(vinylidenefluoride)–ZnO (PVDF–ZnO) nanocomposites with mechanically activated ZnO nanoparticle fillers were investigated using thermal and mechanical analysis and AFM and PFM. Differential scanning calorimetry (DSC) investigated the effect of ZnO nanoparticles on the crystallinity of the polymer, under controlled heating and cooling. Atomic force (AFM) microscopy was used to record the surfaces of the samples. Nanocomposite surface roughness shows the presence of the different phases inside of the matrix, where rough samples contain a higher proportion of the β phase. PFM was performed to investigate the piezoresponse of the composites. Nanoidentation showed that the mechanical activation of the filler (ZnO) increases the Young modulus with the activation time. Molecular simulations in periodic systems (PVDF–ZnO spherical nanocluster and nanocylinder composite) were used to investigate the influence of particle size and shape on the Young modulus of different phases of PVDF.",
publisher = "Elsevier BV",
journal = "Materials Science and Engineering: B",
title = "Nanomechanical properties of PVDF–ZnO polymer nanocomposite",
pages = "116126",
volume = "287",
doi = "10.1016/j.mseb.2022.116126",
url = "https://hdl.handle.net/21.15107/rcub_dais_13436"
}
Peleš Tadić, A., Blagojević, V. A., Stojanović, D., Ostojić, S. B., Tasić, N., Kosanović, D., Uskoković, P.,& Pavlović, V. B.. (2023). Nanomechanical properties of PVDF–ZnO polymer nanocomposite. in Materials Science and Engineering: B
Elsevier BV., 287, 116126.
https://doi.org/10.1016/j.mseb.2022.116126
https://hdl.handle.net/21.15107/rcub_dais_13436
Peleš Tadić A, Blagojević VA, Stojanović D, Ostojić SB, Tasić N, Kosanović D, Uskoković P, Pavlović VB. Nanomechanical properties of PVDF–ZnO polymer nanocomposite. in Materials Science and Engineering: B. 2023;287:116126.
doi:10.1016/j.mseb.2022.116126
https://hdl.handle.net/21.15107/rcub_dais_13436 .
Peleš Tadić, Adriana, Blagojević, Vladimir A., Stojanović, Dušica, Ostojić, Sanja B., Tasić, Nikola, Kosanović, Darko, Uskoković, Petar, Pavlović, Vladimir B., "Nanomechanical properties of PVDF–ZnO polymer nanocomposite" in Materials Science and Engineering: B, 287 (2023):116126,
https://doi.org/10.1016/j.mseb.2022.116126 .,
https://hdl.handle.net/21.15107/rcub_dais_13436 .

Alkali activated slag based on steelmaking slag: application and properties

Nikolić, Irena; Radmilović, Vuk V.; Marković, Smilja; Veselinović, Ljiljana; Janković-Častvan, Ivona; Radmilović, Velimir R.

(Belgrade : Serbian Academy of Sciences and Arts, 2022)

TY  - CONF
AU  - Nikolić, Irena
AU  - Radmilović, Vuk V.
AU  - Marković, Smilja
AU  - Veselinović, Ljiljana
AU  - Janković-Častvan, Ivona
AU  - Radmilović, Velimir R.
PY  - 2022
UR  - https://dais.sanu.ac.rs/123456789/13638
AB  - Alkali activated slag (AAS) is an environmentally friendly material which were extensively investigated in a pass two decade. Currently, these materials are considering as an effective alternative for cement binder. Process of slag alkali activation involves a chemical reaction between solid calcium aluminosilicate materials and a highly alkaline activator. The alkali activation mechanism of slag consists of the slag dissolution in a highly alkaline which is followed by the condensation and hardening processes yielding formation of calcium (alumina) silicate hydrate C– (A)–S–H gel as a reaction product of slag alkali activation. Properties of these materials primarily depends on the choice of solid row materials. Primarily, granulated blast furnace slag, by product of iron production) is considering as a precursor for AAS synthesis. However, an important shift towards the use of steelmaking slag is also observed. Although electric arc furnace slag has already found its application mainly in civil engineering, this investigation has aimed to investigate properties of AAS prepared using the electric arc furnace slag (EAFS) with an emphasize with different possibilities of its application. Characterization of AAS involved XRDP, SEM/EDS and pore size analysis with the aim to build up a detailed illustration of AAS from the stand point of different application.
PB  - Belgrade : Serbian Academy of Sciences and Arts
C3  - Program & Book of Abstracts / Second International Conference ELMINA 2022, Belgrade, Serbia, August 22nd-26th, 2022
T1  - Alkali activated slag based on steelmaking slag: application and properties
SP  - 92
EP  - 93
UR  - https://hdl.handle.net/21.15107/rcub_dais_13638
ER  - 
@conference{
author = "Nikolić, Irena and Radmilović, Vuk V. and Marković, Smilja and Veselinović, Ljiljana and Janković-Častvan, Ivona and Radmilović, Velimir R.",
year = "2022",
abstract = "Alkali activated slag (AAS) is an environmentally friendly material which were extensively investigated in a pass two decade. Currently, these materials are considering as an effective alternative for cement binder. Process of slag alkali activation involves a chemical reaction between solid calcium aluminosilicate materials and a highly alkaline activator. The alkali activation mechanism of slag consists of the slag dissolution in a highly alkaline which is followed by the condensation and hardening processes yielding formation of calcium (alumina) silicate hydrate C– (A)–S–H gel as a reaction product of slag alkali activation. Properties of these materials primarily depends on the choice of solid row materials. Primarily, granulated blast furnace slag, by product of iron production) is considering as a precursor for AAS synthesis. However, an important shift towards the use of steelmaking slag is also observed. Although electric arc furnace slag has already found its application mainly in civil engineering, this investigation has aimed to investigate properties of AAS prepared using the electric arc furnace slag (EAFS) with an emphasize with different possibilities of its application. Characterization of AAS involved XRDP, SEM/EDS and pore size analysis with the aim to build up a detailed illustration of AAS from the stand point of different application.",
publisher = "Belgrade : Serbian Academy of Sciences and Arts",
journal = "Program & Book of Abstracts / Second International Conference ELMINA 2022, Belgrade, Serbia, August 22nd-26th, 2022",
title = "Alkali activated slag based on steelmaking slag: application and properties",
pages = "92-93",
url = "https://hdl.handle.net/21.15107/rcub_dais_13638"
}
Nikolić, I., Radmilović, V. V., Marković, S., Veselinović, L., Janković-Častvan, I.,& Radmilović, V. R.. (2022). Alkali activated slag based on steelmaking slag: application and properties. in Program & Book of Abstracts / Second International Conference ELMINA 2022, Belgrade, Serbia, August 22nd-26th, 2022
Belgrade : Serbian Academy of Sciences and Arts., 92-93.
https://hdl.handle.net/21.15107/rcub_dais_13638
Nikolić I, Radmilović VV, Marković S, Veselinović L, Janković-Častvan I, Radmilović VR. Alkali activated slag based on steelmaking slag: application and properties. in Program & Book of Abstracts / Second International Conference ELMINA 2022, Belgrade, Serbia, August 22nd-26th, 2022. 2022;:92-93.
https://hdl.handle.net/21.15107/rcub_dais_13638 .
Nikolić, Irena, Radmilović, Vuk V., Marković, Smilja, Veselinović, Ljiljana, Janković-Častvan, Ivona, Radmilović, Velimir R., "Alkali activated slag based on steelmaking slag: application and properties" in Program & Book of Abstracts / Second International Conference ELMINA 2022, Belgrade, Serbia, August 22nd-26th, 2022 (2022):92-93,
https://hdl.handle.net/21.15107/rcub_dais_13638 .

Improving the contact surface between TiO2 nanotubes and MAPbBr3 to make perovskite solar cells

Stefanović, Milica; Lukić, Ivana; Vujančević, Jelena; Petrović, Rada; Janaćković, Đorđe

(Belgrade : Serbian Academy of Sciences and Arts, 2022)

TY  - CONF
AU  - Stefanović, Milica
AU  - Lukić, Ivana
AU  - Vujančević, Jelena
AU  - Petrović, Rada
AU  - Janaćković, Đorđe
PY  - 2022
UR  - https://dais.sanu.ac.rs/123456789/13636
AB  - The organo-inorganic perovskites are extraordinary materials that have recently revolutionized the field of photovoltaics due to their low-cost fabrication and high optical absorption. In a short period, they reached great efficiency. Many parameters which affect the quality of perovskite films can be optimized, so the efficiency of these devices can be further improved. In perovskite solar cells, the perovskite layer is an active layer that absorbs the visible part of the spectrum, resulting in the formation of the electron-hole pair. To decrease the recombination of charge carriers, the construction of solar cells requires the existence of two additional layers in order to separate the holes and electrons. TiO2 could be used as an electron transport layer because its conduction band (CB) lies under the CB of perovskite. In that way, electrons diffuse from CB of perovskite to CB of TiO2. For these experiments, TiO2 nanotubular structure provides a one-dimensional transmission channel for the charge carriers, which resulting in faster carrier transport. Perovskite methylammonium lead bromide (MAPbBr3) was coupled with TiO2 nanotube arrays which were synthesized by anodization of Ti foil and annealed at 450 °C. The most used methods for deposition of perovskite materials on mesoporous and planar TiO2 are: one-step deposition, two-step sequential deposition, and vapor-assisted solution processing. Disadvantage of these methods is a small contact area between TiO2 and perovskite. The aim of this research was to increase the contact surface of the perovskite and TiO2 nanotubes by filling the nanotubes with the perovskite material in order to improve electron transport.
PB  - Belgrade : Serbian Academy of Sciences and Arts
C3  - Program & Book of Abstracts / Second International Conference ELMINA 2022, Belgrade, Serbia, August 22nd-26th, 2022
T1  - Improving the contact surface between TiO2 nanotubes and MAPbBr3 to make perovskite solar cells
SP  - 188
EP  - 189
UR  - https://hdl.handle.net/21.15107/rcub_dais_13636
ER  - 
@conference{
author = "Stefanović, Milica and Lukić, Ivana and Vujančević, Jelena and Petrović, Rada and Janaćković, Đorđe",
year = "2022",
abstract = "The organo-inorganic perovskites are extraordinary materials that have recently revolutionized the field of photovoltaics due to their low-cost fabrication and high optical absorption. In a short period, they reached great efficiency. Many parameters which affect the quality of perovskite films can be optimized, so the efficiency of these devices can be further improved. In perovskite solar cells, the perovskite layer is an active layer that absorbs the visible part of the spectrum, resulting in the formation of the electron-hole pair. To decrease the recombination of charge carriers, the construction of solar cells requires the existence of two additional layers in order to separate the holes and electrons. TiO2 could be used as an electron transport layer because its conduction band (CB) lies under the CB of perovskite. In that way, electrons diffuse from CB of perovskite to CB of TiO2. For these experiments, TiO2 nanotubular structure provides a one-dimensional transmission channel for the charge carriers, which resulting in faster carrier transport. Perovskite methylammonium lead bromide (MAPbBr3) was coupled with TiO2 nanotube arrays which were synthesized by anodization of Ti foil and annealed at 450 °C. The most used methods for deposition of perovskite materials on mesoporous and planar TiO2 are: one-step deposition, two-step sequential deposition, and vapor-assisted solution processing. Disadvantage of these methods is a small contact area between TiO2 and perovskite. The aim of this research was to increase the contact surface of the perovskite and TiO2 nanotubes by filling the nanotubes with the perovskite material in order to improve electron transport.",
publisher = "Belgrade : Serbian Academy of Sciences and Arts",
journal = "Program & Book of Abstracts / Second International Conference ELMINA 2022, Belgrade, Serbia, August 22nd-26th, 2022",
title = "Improving the contact surface between TiO2 nanotubes and MAPbBr3 to make perovskite solar cells",
pages = "188-189",
url = "https://hdl.handle.net/21.15107/rcub_dais_13636"
}
Stefanović, M., Lukić, I., Vujančević, J., Petrović, R.,& Janaćković, Đ.. (2022). Improving the contact surface between TiO2 nanotubes and MAPbBr3 to make perovskite solar cells. in Program & Book of Abstracts / Second International Conference ELMINA 2022, Belgrade, Serbia, August 22nd-26th, 2022
Belgrade : Serbian Academy of Sciences and Arts., 188-189.
https://hdl.handle.net/21.15107/rcub_dais_13636
Stefanović M, Lukić I, Vujančević J, Petrović R, Janaćković Đ. Improving the contact surface between TiO2 nanotubes and MAPbBr3 to make perovskite solar cells. in Program & Book of Abstracts / Second International Conference ELMINA 2022, Belgrade, Serbia, August 22nd-26th, 2022. 2022;:188-189.
https://hdl.handle.net/21.15107/rcub_dais_13636 .
Stefanović, Milica, Lukić, Ivana, Vujančević, Jelena, Petrović, Rada, Janaćković, Đorđe, "Improving the contact surface between TiO2 nanotubes and MAPbBr3 to make perovskite solar cells" in Program & Book of Abstracts / Second International Conference ELMINA 2022, Belgrade, Serbia, August 22nd-26th, 2022 (2022):188-189,
https://hdl.handle.net/21.15107/rcub_dais_13636 .

Corrosion behavior of copper in 3 % NaCl with addition of cynarae extract

Jokić, Bojan; Gvozdenović, Milica; Jovanović, Marijana; Jugović, Branimir; Grgur, Branimir

(Beograd : Udruženje inženjera Srbije za koroziju i zaštitu materijala UISKOZAM, 2022)

TY  - CONF
AU  - Jokić, Bojan
AU  - Gvozdenović, Milica
AU  - Jovanović, Marijana
AU  - Jugović, Branimir
AU  - Grgur, Branimir
PY  - 2022
UR  - https://dais.sanu.ac.rs/123456789/13649
AB  - In this work, corrosion behavior of cooper in corrosion media consisted of aerated aqueous electrolyte of 3% NaCl with addition of different amount of cynarae extract as green corrosion inhibitor, is presented. Techniques used in this study involved open circuit measurements, evaluation of charge transfer resistance and corrosion current density during exposure to corrosion environment. Also, electrochemical impedance spectroscopy measurements are presented. Potentiodymamic polarization curves were also used for the evaluation of the corrosion current density and corrosion potential of coper in corrosion media. Based on these results, it was concluded that the satisfactory results of corrosion inhibition exceeding 70 % were obtained with small amount of only 37*10-2 of mas. % of cynarae extract, based on open circuit behavior which involved decrease of the open circuit potentials of copper in the presence of cynarae extract it was concluded that this extract served as cathodic inhibitor.
AB  - Koroziono ponašanje bakra u aerisanom vodenom rastvoru 3% NaCl bez i sa dodatkom različite količine ekstrakta cynarae (artičoka) je ispitano u cilju evaluacije inhibicije korozije bakra i mogućnosti primene ekstrakta cynarae kao zelenog inhibitora korozije. Za evaluaciju efikasnosti zaštite korišćene su uobičajene eksperimntalne tehnike praćenja potencija otvorenog kola, otpornosti prenosa naelektrisanja i struje korozije u vremenu kao i spektroskopija elektrohemijske impedancije. Ustanovljeno je da veoma male količine ovog inhibitora od svega 37*10-2 mas. % pružaju zadovoljavajuću zaštitu od korozije u 3% NaCl. Na osnovu smanjenja potencijala otvorenog kola bakra u prisustvu ekstrakta cynarae, ustanovljeno je da je inhibitor katodnog tipa.
PB  - Beograd : Udruženje inženjera Srbije za koroziju i zaštitu materijala UISKOZAM
C3  - Meeting point of the science and practice in the fields of corrosion, materials and environmental protection : proceedings = Stecište nauke i prakse u oblastima korozije, zaštite materijala i životne sredine : knjiga radova / XXIII YuCorr International Conference = XXIII YuCorr Međunarodna konferencija, May 16-19, 2022, Divčibare, Serbia
T1  - Corrosion behavior of copper in 3 % NaCl with addition of cynarae extract
T1  - Koroziono ponašanje bakra u 3% rastvoru NaCl sa dodatkom ekstrakta cynarae
SP  - poster-159
EP  - poster-164
UR  - https://hdl.handle.net/21.15107/rcub_dais_13649
ER  - 
@conference{
author = "Jokić, Bojan and Gvozdenović, Milica and Jovanović, Marijana and Jugović, Branimir and Grgur, Branimir",
year = "2022",
abstract = "In this work, corrosion behavior of cooper in corrosion media consisted of aerated aqueous electrolyte of 3% NaCl with addition of different amount of cynarae extract as green corrosion inhibitor, is presented. Techniques used in this study involved open circuit measurements, evaluation of charge transfer resistance and corrosion current density during exposure to corrosion environment. Also, electrochemical impedance spectroscopy measurements are presented. Potentiodymamic polarization curves were also used for the evaluation of the corrosion current density and corrosion potential of coper in corrosion media. Based on these results, it was concluded that the satisfactory results of corrosion inhibition exceeding 70 % were obtained with small amount of only 37*10-2 of mas. % of cynarae extract, based on open circuit behavior which involved decrease of the open circuit potentials of copper in the presence of cynarae extract it was concluded that this extract served as cathodic inhibitor., Koroziono ponašanje bakra u aerisanom vodenom rastvoru 3% NaCl bez i sa dodatkom različite količine ekstrakta cynarae (artičoka) je ispitano u cilju evaluacije inhibicije korozije bakra i mogućnosti primene ekstrakta cynarae kao zelenog inhibitora korozije. Za evaluaciju efikasnosti zaštite korišćene su uobičajene eksperimntalne tehnike praćenja potencija otvorenog kola, otpornosti prenosa naelektrisanja i struje korozije u vremenu kao i spektroskopija elektrohemijske impedancije. Ustanovljeno je da veoma male količine ovog inhibitora od svega 37*10-2 mas. % pružaju zadovoljavajuću zaštitu od korozije u 3% NaCl. Na osnovu smanjenja potencijala otvorenog kola bakra u prisustvu ekstrakta cynarae, ustanovljeno je da je inhibitor katodnog tipa.",
publisher = "Beograd : Udruženje inženjera Srbije za koroziju i zaštitu materijala UISKOZAM",
journal = "Meeting point of the science and practice in the fields of corrosion, materials and environmental protection : proceedings = Stecište nauke i prakse u oblastima korozije, zaštite materijala i životne sredine : knjiga radova / XXIII YuCorr International Conference = XXIII YuCorr Međunarodna konferencija, May 16-19, 2022, Divčibare, Serbia",
title = "Corrosion behavior of copper in 3 % NaCl with addition of cynarae extract, Koroziono ponašanje bakra u 3% rastvoru NaCl sa dodatkom ekstrakta cynarae",
pages = "poster-159-poster-164",
url = "https://hdl.handle.net/21.15107/rcub_dais_13649"
}
Jokić, B., Gvozdenović, M., Jovanović, M., Jugović, B.,& Grgur, B.. (2022). Corrosion behavior of copper in 3 % NaCl with addition of cynarae extract. in Meeting point of the science and practice in the fields of corrosion, materials and environmental protection : proceedings = Stecište nauke i prakse u oblastima korozije, zaštite materijala i životne sredine : knjiga radova / XXIII YuCorr International Conference = XXIII YuCorr Međunarodna konferencija, May 16-19, 2022, Divčibare, Serbia
Beograd : Udruženje inženjera Srbije za koroziju i zaštitu materijala UISKOZAM., poster-159-poster-164.
https://hdl.handle.net/21.15107/rcub_dais_13649
Jokić B, Gvozdenović M, Jovanović M, Jugović B, Grgur B. Corrosion behavior of copper in 3 % NaCl with addition of cynarae extract. in Meeting point of the science and practice in the fields of corrosion, materials and environmental protection : proceedings = Stecište nauke i prakse u oblastima korozije, zaštite materijala i životne sredine : knjiga radova / XXIII YuCorr International Conference = XXIII YuCorr Međunarodna konferencija, May 16-19, 2022, Divčibare, Serbia. 2022;:poster-159-poster-164.
https://hdl.handle.net/21.15107/rcub_dais_13649 .
Jokić, Bojan, Gvozdenović, Milica, Jovanović, Marijana, Jugović, Branimir, Grgur, Branimir, "Corrosion behavior of copper in 3 % NaCl with addition of cynarae extract" in Meeting point of the science and practice in the fields of corrosion, materials and environmental protection : proceedings = Stecište nauke i prakse u oblastima korozije, zaštite materijala i životne sredine : knjiga radova / XXIII YuCorr International Conference = XXIII YuCorr Međunarodna konferencija, May 16-19, 2022, Divčibare, Serbia (2022):poster-159-poster-164,
https://hdl.handle.net/21.15107/rcub_dais_13649 .

Capacitive properties of electrochemically synthesized polyaniline on graphite electrode

Gojgić, Jelena; Petrović, Miloš; Jugović, Branimir; Grgur, Branimir; Jokić, Bojan; Gvozdenović, Milica

(Beograd : Udruženje inženjera Srbije za koroziju i zaštitu materijala UISKOZAM, 2022)

TY  - CONF
AU  - Gojgić, Jelena
AU  - Petrović, Miloš
AU  - Jugović, Branimir
AU  - Grgur, Branimir
AU  - Jokić, Bojan
AU  - Gvozdenović, Milica
PY  - 2022
UR  - https://dais.sanu.ac.rs/123456789/13650
AB  - Intrinsically conducting polymers, especially polyaniline (PANI), are widely investigated in the field of energy storage and conversion due to the highly reversible electrochemistry of doping/dedoping. These reactions are responsible for PANI’s high capacitance, often reported as pseudocapacitance. In this work, PANI electrodes were obtained by electrochemical polymerization of aniline monomer, with different polymerization charges ranging between 0.125 and 1.0 mA cm-2, on a graphite electrode, at the constant current density of 2.0 mA cm-2. The electrolyte used in this study consisted of 1.0 mol dm-3 H2SO4 and 0.2 mol dm-3 aniline. Electrochemical characterization of the PANI electrode involved cyclic voltammetry, chronopotentiometric charge/discharge and electrochemical impedance spectroscopy at constant potentials. Specific capacitance was determined from these techniques following the procedure for pseudocapacitive electrodes. After 250 cycles of charge/discharge with the current density of 10 mA cm-2, only 7 % of the capacitance was lost, indicating good stability of PANI that likely originates from its structure comprising a shared divalent sulfate ion between two monomer units.
AB  - Elektroprovodni polimeri, prvenstveno polianilin (PANI), su intenzivno proučavani u oblasti konverzije i skladištenja električne energije, zahvaljujući visokoj reverzibilnosti reakcije dopovanja/dedopovanje. Ove reakcije su odgovorne za visoku specifičnu kapacitivnost PANI koja se često u literaturi označava kao pseudokapacitivnost. U ovom radu, elektrode na bazi PANI dobijene su oksidativnom elektrohemijskom polimerizacijom anilina različitim kapacitetima polimerizacije u opsegu od 0,125 do 1,0 mA cm-2 na elektrodi od grafita u galvanostatskim uslovima gustinom struje od 2,0 mA cm-2. Kao elektrolit korišćen je vodeni rastvor 1,0 mol dm-3 H2SO4 uz dodatak 0,2 mol dm-3 anilina. Za elektrohemijsku karakterizaciju elektrode na bazi PANI korišćene su tehnike ciklične voltametrije, hronopotenciometrijskog snimanja krivih punjenja/pražnjenja i spektroskopija elektrohemijske impedanse na konstantnom potencijalu. Specifična kapacitivnost PANI elektrode određivana je na način uobičajen za pseudokapacitivne elektrode. Na osnovu 250 sukcesivnih ciklusa punjenja i pražnjenja gustinom struje od 10 mA cm-2, utvrđeno je gubitak kapacitivnosti od svega 7%, što se verovatno može dovesti u vezu sa povećanom stabilnošću PANI usled strukture koja podrazumeva deljenje dvovalentnog sulfatnog jona između dve jedinice monomera.
PB  - Beograd : Udruženje inženjera Srbije za koroziju i zaštitu materijala UISKOZAM
C3  - Meeting point of the science and practice in the fields of corrosion, materials and environmental protection : proceedings = Stecište nauke i prakse u oblastima korozije, zaštite materijala i životne sredine : knjiga radova / XXIII YuCorr International Conference = XXIII YuCorr Međunarodna konferencija, May 16-19, 2022, Divčibare, Serbia
T1  - Capacitive properties of electrochemically synthesized polyaniline on graphite electrode
T1  - Kapacitivna svojstva elekrode na bazi elektrohemijski formiranog polianilina
SP  - poster-151
UR  - https://hdl.handle.net/21.15107/rcub_dais_13650
ER  - 
@conference{
author = "Gojgić, Jelena and Petrović, Miloš and Jugović, Branimir and Grgur, Branimir and Jokić, Bojan and Gvozdenović, Milica",
year = "2022",
abstract = "Intrinsically conducting polymers, especially polyaniline (PANI), are widely investigated in the field of energy storage and conversion due to the highly reversible electrochemistry of doping/dedoping. These reactions are responsible for PANI’s high capacitance, often reported as pseudocapacitance. In this work, PANI electrodes were obtained by electrochemical polymerization of aniline monomer, with different polymerization charges ranging between 0.125 and 1.0 mA cm-2, on a graphite electrode, at the constant current density of 2.0 mA cm-2. The electrolyte used in this study consisted of 1.0 mol dm-3 H2SO4 and 0.2 mol dm-3 aniline. Electrochemical characterization of the PANI electrode involved cyclic voltammetry, chronopotentiometric charge/discharge and electrochemical impedance spectroscopy at constant potentials. Specific capacitance was determined from these techniques following the procedure for pseudocapacitive electrodes. After 250 cycles of charge/discharge with the current density of 10 mA cm-2, only 7 % of the capacitance was lost, indicating good stability of PANI that likely originates from its structure comprising a shared divalent sulfate ion between two monomer units., Elektroprovodni polimeri, prvenstveno polianilin (PANI), su intenzivno proučavani u oblasti konverzije i skladištenja električne energije, zahvaljujući visokoj reverzibilnosti reakcije dopovanja/dedopovanje. Ove reakcije su odgovorne za visoku specifičnu kapacitivnost PANI koja se često u literaturi označava kao pseudokapacitivnost. U ovom radu, elektrode na bazi PANI dobijene su oksidativnom elektrohemijskom polimerizacijom anilina različitim kapacitetima polimerizacije u opsegu od 0,125 do 1,0 mA cm-2 na elektrodi od grafita u galvanostatskim uslovima gustinom struje od 2,0 mA cm-2. Kao elektrolit korišćen je vodeni rastvor 1,0 mol dm-3 H2SO4 uz dodatak 0,2 mol dm-3 anilina. Za elektrohemijsku karakterizaciju elektrode na bazi PANI korišćene su tehnike ciklične voltametrije, hronopotenciometrijskog snimanja krivih punjenja/pražnjenja i spektroskopija elektrohemijske impedanse na konstantnom potencijalu. Specifična kapacitivnost PANI elektrode određivana je na način uobičajen za pseudokapacitivne elektrode. Na osnovu 250 sukcesivnih ciklusa punjenja i pražnjenja gustinom struje od 10 mA cm-2, utvrđeno je gubitak kapacitivnosti od svega 7%, što se verovatno može dovesti u vezu sa povećanom stabilnošću PANI usled strukture koja podrazumeva deljenje dvovalentnog sulfatnog jona između dve jedinice monomera.",
publisher = "Beograd : Udruženje inženjera Srbije za koroziju i zaštitu materijala UISKOZAM",
journal = "Meeting point of the science and practice in the fields of corrosion, materials and environmental protection : proceedings = Stecište nauke i prakse u oblastima korozije, zaštite materijala i životne sredine : knjiga radova / XXIII YuCorr International Conference = XXIII YuCorr Međunarodna konferencija, May 16-19, 2022, Divčibare, Serbia",
title = "Capacitive properties of electrochemically synthesized polyaniline on graphite electrode, Kapacitivna svojstva elekrode na bazi elektrohemijski formiranog polianilina",
pages = "poster-151",
url = "https://hdl.handle.net/21.15107/rcub_dais_13650"
}
Gojgić, J., Petrović, M., Jugović, B., Grgur, B., Jokić, B.,& Gvozdenović, M.. (2022). Capacitive properties of electrochemically synthesized polyaniline on graphite electrode. in Meeting point of the science and practice in the fields of corrosion, materials and environmental protection : proceedings = Stecište nauke i prakse u oblastima korozije, zaštite materijala i životne sredine : knjiga radova / XXIII YuCorr International Conference = XXIII YuCorr Međunarodna konferencija, May 16-19, 2022, Divčibare, Serbia
Beograd : Udruženje inženjera Srbije za koroziju i zaštitu materijala UISKOZAM., poster-151.
https://hdl.handle.net/21.15107/rcub_dais_13650
Gojgić J, Petrović M, Jugović B, Grgur B, Jokić B, Gvozdenović M. Capacitive properties of electrochemically synthesized polyaniline on graphite electrode. in Meeting point of the science and practice in the fields of corrosion, materials and environmental protection : proceedings = Stecište nauke i prakse u oblastima korozije, zaštite materijala i životne sredine : knjiga radova / XXIII YuCorr International Conference = XXIII YuCorr Međunarodna konferencija, May 16-19, 2022, Divčibare, Serbia. 2022;:poster-151.
https://hdl.handle.net/21.15107/rcub_dais_13650 .
Gojgić, Jelena, Petrović, Miloš, Jugović, Branimir, Grgur, Branimir, Jokić, Bojan, Gvozdenović, Milica, "Capacitive properties of electrochemically synthesized polyaniline on graphite electrode" in Meeting point of the science and practice in the fields of corrosion, materials and environmental protection : proceedings = Stecište nauke i prakse u oblastima korozije, zaštite materijala i životne sredine : knjiga radova / XXIII YuCorr International Conference = XXIII YuCorr Međunarodna konferencija, May 16-19, 2022, Divčibare, Serbia (2022):poster-151,
https://hdl.handle.net/21.15107/rcub_dais_13650 .

Electrical properties of electrochemically co-polymerized aniline and sulphanilic acid

Novaković, Nikola; Petrović, Miloš; Jugović, Branimir; Grgur, Branimir; Gvozdenović, Milica

(Beograd : Udruženje inženjera Srbije za koroziju i zaštitu materijala UISKOZAM, 2022)

TY  - CONF
AU  - Novaković, Nikola
AU  - Petrović, Miloš
AU  - Jugović, Branimir
AU  - Grgur, Branimir
AU  - Gvozdenović, Milica
PY  - 2022
UR  - https://dais.sanu.ac.rs/123456789/13651
AB  - Electrochemical synthesis of poly(aniline-co-(sulfanilic acid)) was performed on a graphite electrode with constant current densities from an aqueous electrolyte containing 1.0 mol dm-3 H2SO4 and 0.25 mol dm-3 monomers with different ratios of aniline and sulfanilic acid. Optimal conditions for copolymerization were set to the current density of 0.75 mA cm-2 and the electrolyte containing 0.15 mol dm-3 aniline and 0.10 mol dm-3 sulfanilic acid. Electrochemical characterization of the poly(aniline-co-(sulfanilic acid)) electrode was performed using cyclic voltammetry and galvanostatic charge/discharge techniques. Electrical properties such as specific power and specific energy at different discharge currents were also determined. Based on the Ragon plot, it was observed that the poly(aniline-co-(sulfanilic acid)) electrode exhibited battery features at low discharge currents. In contrast, it was possible to achieve specific power of supercapacitors at high discharge currents. Moreover, after 4000 cycles of charge/discharge poly(aniline-co-(sulfanilic acid)), capacity retention exceeding 90 % was obtained.
AB  - Elektrohemijska kopolimerizacija anilina i sulfanilne kiseline ostvarena je u galvanostatskim uslovima različitim gustinama struje na grafitnoj elektrodi. Kao elektrolit korišćen je vodeni rastvor 1.0 mol dm-3 H2SO4 sa dodatkom 0.25 mol dm-3 monomera različitog odnosa anilina i sulfanilne kiseline. Izabrani su optimalni uslovi za sintezu u pogledu gustine struje polimerizacije od 0.75 mA cm-2 i sastava elektrolita koji je sadržavao 0.15 mol dm-3 anilina i 0.10 mol dm-3 sulfanilne kiseline. Za elektrohemijsku karakterizaciju elektrode na bazi kopolimera anilina i sulfanilne kiseline korišćene su tehnike ciklične voltametrije i snimanja hronopotenciometrijskih krivih punjenja/pražnjenja. Na osnovu krivih pražnjenja procenjene su električne karakteristike ove elektrode: specifična energija i specifična snaga. Na osnovu Ragonovog dijagrama pokazano je da elektroda na bazi kopolimera anilina i sulfanilne kiseline poseduje baterijska svojstva pri niskim strujama pražnjenja, dok se pri visokim strujama pražnjenja ponaša kao elektroda superkondenzatora. Takođe, ova elektroda je nakon 4000 ciklusa punjenja i pražnjenja zadržala preko 90 % početnog kapaciteta.
PB  - Beograd : Udruženje inženjera Srbije za koroziju i zaštitu materijala UISKOZAM
C3  - Meeting point of the science and practice in the fields of corrosion, materials and environmental protection : proceedings = Stecište nauke i prakse u oblastima korozije, zaštite materijala i životne sredine : knjiga radova / XXIII YuCorr International Conference = XXIII YuCorr Međunarodna konferencija, May 16-19, 2022, Divčibare, Serbia
T1  - Electrical properties of electrochemically co-polymerized aniline and sulphanilic acid
T1  - Električna svojstva elektrohemijski kopolimerizovanog anilina i sulfanilne kiseline
SP  - oral-95
EP  - oral-100
UR  - https://hdl.handle.net/21.15107/rcub_dais_13651
ER  - 
@conference{
author = "Novaković, Nikola and Petrović, Miloš and Jugović, Branimir and Grgur, Branimir and Gvozdenović, Milica",
year = "2022",
abstract = "Electrochemical synthesis of poly(aniline-co-(sulfanilic acid)) was performed on a graphite electrode with constant current densities from an aqueous electrolyte containing 1.0 mol dm-3 H2SO4 and 0.25 mol dm-3 monomers with different ratios of aniline and sulfanilic acid. Optimal conditions for copolymerization were set to the current density of 0.75 mA cm-2 and the electrolyte containing 0.15 mol dm-3 aniline and 0.10 mol dm-3 sulfanilic acid. Electrochemical characterization of the poly(aniline-co-(sulfanilic acid)) electrode was performed using cyclic voltammetry and galvanostatic charge/discharge techniques. Electrical properties such as specific power and specific energy at different discharge currents were also determined. Based on the Ragon plot, it was observed that the poly(aniline-co-(sulfanilic acid)) electrode exhibited battery features at low discharge currents. In contrast, it was possible to achieve specific power of supercapacitors at high discharge currents. Moreover, after 4000 cycles of charge/discharge poly(aniline-co-(sulfanilic acid)), capacity retention exceeding 90 % was obtained., Elektrohemijska kopolimerizacija anilina i sulfanilne kiseline ostvarena je u galvanostatskim uslovima različitim gustinama struje na grafitnoj elektrodi. Kao elektrolit korišćen je vodeni rastvor 1.0 mol dm-3 H2SO4 sa dodatkom 0.25 mol dm-3 monomera različitog odnosa anilina i sulfanilne kiseline. Izabrani su optimalni uslovi za sintezu u pogledu gustine struje polimerizacije od 0.75 mA cm-2 i sastava elektrolita koji je sadržavao 0.15 mol dm-3 anilina i 0.10 mol dm-3 sulfanilne kiseline. Za elektrohemijsku karakterizaciju elektrode na bazi kopolimera anilina i sulfanilne kiseline korišćene su tehnike ciklične voltametrije i snimanja hronopotenciometrijskih krivih punjenja/pražnjenja. Na osnovu krivih pražnjenja procenjene su električne karakteristike ove elektrode: specifična energija i specifična snaga. Na osnovu Ragonovog dijagrama pokazano je da elektroda na bazi kopolimera anilina i sulfanilne kiseline poseduje baterijska svojstva pri niskim strujama pražnjenja, dok se pri visokim strujama pražnjenja ponaša kao elektroda superkondenzatora. Takođe, ova elektroda je nakon 4000 ciklusa punjenja i pražnjenja zadržala preko 90 % početnog kapaciteta.",
publisher = "Beograd : Udruženje inženjera Srbije za koroziju i zaštitu materijala UISKOZAM",
journal = "Meeting point of the science and practice in the fields of corrosion, materials and environmental protection : proceedings = Stecište nauke i prakse u oblastima korozije, zaštite materijala i životne sredine : knjiga radova / XXIII YuCorr International Conference = XXIII YuCorr Međunarodna konferencija, May 16-19, 2022, Divčibare, Serbia",
title = "Electrical properties of electrochemically co-polymerized aniline and sulphanilic acid, Električna svojstva elektrohemijski kopolimerizovanog anilina i sulfanilne kiseline",
pages = "oral-95-oral-100",
url = "https://hdl.handle.net/21.15107/rcub_dais_13651"
}
Novaković, N., Petrović, M., Jugović, B., Grgur, B.,& Gvozdenović, M.. (2022). Electrical properties of electrochemically co-polymerized aniline and sulphanilic acid. in Meeting point of the science and practice in the fields of corrosion, materials and environmental protection : proceedings = Stecište nauke i prakse u oblastima korozije, zaštite materijala i životne sredine : knjiga radova / XXIII YuCorr International Conference = XXIII YuCorr Međunarodna konferencija, May 16-19, 2022, Divčibare, Serbia
Beograd : Udruženje inženjera Srbije za koroziju i zaštitu materijala UISKOZAM., oral-95-oral-100.
https://hdl.handle.net/21.15107/rcub_dais_13651
Novaković N, Petrović M, Jugović B, Grgur B, Gvozdenović M. Electrical properties of electrochemically co-polymerized aniline and sulphanilic acid. in Meeting point of the science and practice in the fields of corrosion, materials and environmental protection : proceedings = Stecište nauke i prakse u oblastima korozije, zaštite materijala i životne sredine : knjiga radova / XXIII YuCorr International Conference = XXIII YuCorr Međunarodna konferencija, May 16-19, 2022, Divčibare, Serbia. 2022;:oral-95-oral-100.
https://hdl.handle.net/21.15107/rcub_dais_13651 .
Novaković, Nikola, Petrović, Miloš, Jugović, Branimir, Grgur, Branimir, Gvozdenović, Milica, "Electrical properties of electrochemically co-polymerized aniline and sulphanilic acid" in Meeting point of the science and practice in the fields of corrosion, materials and environmental protection : proceedings = Stecište nauke i prakse u oblastima korozije, zaštite materijala i životne sredine : knjiga radova / XXIII YuCorr International Conference = XXIII YuCorr Međunarodna konferencija, May 16-19, 2022, Divčibare, Serbia (2022):oral-95-oral-100,
https://hdl.handle.net/21.15107/rcub_dais_13651 .

Electrochemical and Electrical Performances of High Energy Storage Polyaniline Electrode with Supercapattery Behavior

Gojgić, Jelena; Petrović, Miloš; Jugović, Branimir; Jokić, Bojan; Grgur, Branimir; Gvozdenović, Milica

(2022)

TY  - JOUR
AU  - Gojgić, Jelena
AU  - Petrović, Miloš
AU  - Jugović, Branimir
AU  - Jokić, Bojan
AU  - Grgur, Branimir
AU  - Gvozdenović, Milica
PY  - 2022
UR  - https://dais.sanu.ac.rs/123456789/13496
AB  - Polyaniline (PANI), due to its highly reversible electrochemistry with superior energy storage and delivery characteristics, is considered as an electrode material in batteries, capacitors, and hybrid systems. We used a facile electrochemical synthesis for the formation of the PANI electrode using galvanostatic polymerization of aniline on the graphite electrode at the current density of 2.0 mA cm−2 from the aqueous electrolyte containing 0.25 mol dm−3 aniline and 1.0 mol dm−3 H2SO4. Electrochemical and electrical characterization suggested excellent energy storage features of the PANI electrode in a three-electrode system with specific energy up to 53 Wh kg−1 and specific power up to 7600 W kg−1. After 2000 successive charge/discharge cycles at 9.5 Ag−1, the PANI electrode retained 95% of the initial capacity, with practically unaltered Coulombic efficiency of nearly 98%, providing a good base for future studies and practical applications.
T2  - Polymers
T2  - Polymers
T1  - Electrochemical and Electrical Performances of High Energy Storage Polyaniline Electrode with Supercapattery Behavior
SP  - 5365
VL  - 14
IS  - 24
DO  - 10.3390/polym14245365
UR  - https://hdl.handle.net/21.15107/rcub_dais_13496
ER  - 
@article{
author = "Gojgić, Jelena and Petrović, Miloš and Jugović, Branimir and Jokić, Bojan and Grgur, Branimir and Gvozdenović, Milica",
year = "2022",
abstract = "Polyaniline (PANI), due to its highly reversible electrochemistry with superior energy storage and delivery characteristics, is considered as an electrode material in batteries, capacitors, and hybrid systems. We used a facile electrochemical synthesis for the formation of the PANI electrode using galvanostatic polymerization of aniline on the graphite electrode at the current density of 2.0 mA cm−2 from the aqueous electrolyte containing 0.25 mol dm−3 aniline and 1.0 mol dm−3 H2SO4. Electrochemical and electrical characterization suggested excellent energy storage features of the PANI electrode in a three-electrode system with specific energy up to 53 Wh kg−1 and specific power up to 7600 W kg−1. After 2000 successive charge/discharge cycles at 9.5 Ag−1, the PANI electrode retained 95% of the initial capacity, with practically unaltered Coulombic efficiency of nearly 98%, providing a good base for future studies and practical applications.",
journal = "Polymers, Polymers",
title = "Electrochemical and Electrical Performances of High Energy Storage Polyaniline Electrode with Supercapattery Behavior",
pages = "5365",
volume = "14",
number = "24",
doi = "10.3390/polym14245365",
url = "https://hdl.handle.net/21.15107/rcub_dais_13496"
}
Gojgić, J., Petrović, M., Jugović, B., Jokić, B., Grgur, B.,& Gvozdenović, M.. (2022). Electrochemical and Electrical Performances of High Energy Storage Polyaniline Electrode with Supercapattery Behavior. in Polymers, 14(24), 5365.
https://doi.org/10.3390/polym14245365
https://hdl.handle.net/21.15107/rcub_dais_13496
Gojgić J, Petrović M, Jugović B, Jokić B, Grgur B, Gvozdenović M. Electrochemical and Electrical Performances of High Energy Storage Polyaniline Electrode with Supercapattery Behavior. in Polymers. 2022;14(24):5365.
doi:10.3390/polym14245365
https://hdl.handle.net/21.15107/rcub_dais_13496 .
Gojgić, Jelena, Petrović, Miloš, Jugović, Branimir, Jokić, Bojan, Grgur, Branimir, Gvozdenović, Milica, "Electrochemical and Electrical Performances of High Energy Storage Polyaniline Electrode with Supercapattery Behavior" in Polymers, 14, no. 24 (2022):5365,
https://doi.org/10.3390/polym14245365 .,
https://hdl.handle.net/21.15107/rcub_dais_13496 .

The Analysis of the Nucleation Process of the Lithium Germanium Phosphate Glass

Matijašević, Srđan; Grujić, Snežana; Nikolić, Jelena; Topalović, Vladimir; Savić, Veljko; Zildžović, Snežana; Labus, Nebojša

(2022)

TY  - JOUR
AU  - Matijašević, Srđan
AU  - Grujić, Snežana
AU  - Nikolić, Jelena
AU  - Topalović, Vladimir
AU  - Savić, Veljko
AU  - Zildžović, Snežana
AU  - Labus, Nebojša
PY  - 2022
UR  - https://dais.sanu.ac.rs/123456789/13580
AB  - The nucleation process of lithium germanium-phosphate glass was studied to determine the temperature range of nucleation and the temperature of the maximum nucleation rate. The differential thermal analysis (DTA), and scanning electron microscope (SEM) were used to reveal the nonisothermal and isothermal process of nucleation, respectively. The crystallization process occurred at a high homogeneous nucleation rate and the spherulitic crystal growth morphology. Nanostructured samples were obtained.
T2  - Science of Sintering
T1  - The Analysis of the Nucleation Process of the Lithium Germanium Phosphate Glass
SP  - 321
EP  - 334
VL  - 54
IS  - 3
DO  - 10.2298/SOS2203321M
UR  - https://hdl.handle.net/21.15107/rcub_dais_13580
ER  - 
@article{
author = "Matijašević, Srđan and Grujić, Snežana and Nikolić, Jelena and Topalović, Vladimir and Savić, Veljko and Zildžović, Snežana and Labus, Nebojša",
year = "2022",
abstract = "The nucleation process of lithium germanium-phosphate glass was studied to determine the temperature range of nucleation and the temperature of the maximum nucleation rate. The differential thermal analysis (DTA), and scanning electron microscope (SEM) were used to reveal the nonisothermal and isothermal process of nucleation, respectively. The crystallization process occurred at a high homogeneous nucleation rate and the spherulitic crystal growth morphology. Nanostructured samples were obtained.",
journal = "Science of Sintering",
title = "The Analysis of the Nucleation Process of the Lithium Germanium Phosphate Glass",
pages = "321-334",
volume = "54",
number = "3",
doi = "10.2298/SOS2203321M",
url = "https://hdl.handle.net/21.15107/rcub_dais_13580"
}
Matijašević, S., Grujić, S., Nikolić, J., Topalović, V., Savić, V., Zildžović, S.,& Labus, N.. (2022). The Analysis of the Nucleation Process of the Lithium Germanium Phosphate Glass. in Science of Sintering, 54(3), 321-334.
https://doi.org/10.2298/SOS2203321M
https://hdl.handle.net/21.15107/rcub_dais_13580
Matijašević S, Grujić S, Nikolić J, Topalović V, Savić V, Zildžović S, Labus N. The Analysis of the Nucleation Process of the Lithium Germanium Phosphate Glass. in Science of Sintering. 2022;54(3):321-334.
doi:10.2298/SOS2203321M
https://hdl.handle.net/21.15107/rcub_dais_13580 .
Matijašević, Srđan, Grujić, Snežana, Nikolić, Jelena, Topalović, Vladimir, Savić, Veljko, Zildžović, Snežana, Labus, Nebojša, "The Analysis of the Nucleation Process of the Lithium Germanium Phosphate Glass" in Science of Sintering, 54, no. 3 (2022):321-334,
https://doi.org/10.2298/SOS2203321M .,
https://hdl.handle.net/21.15107/rcub_dais_13580 .

Supplementary information for the article Jonović, Marko, Jugović, Branimir, Žuža, Milena, Đorđević, Verica, Milašinović, Nikola, Bugarski, Branko, Knežević-Jugović, Zorica, "Immobilization of Horseradish Peroxidase on Magnetite-Alginate Beads to Enable Effective Strong Binding and Enzyme Recycling during Anthraquinone Dyes’ Degradation" in Polymers, 14, no. 13 (2022):2614, https://doi.org/10.3390/polym14132614

Jonović, Marko; Jugović, Branimir; Žuža, Milena; Đorđević, Verica; Milašinović, Nikola; Bugarski, Branko; Knežević-Jugović, Zorica

(MDPI AG, 2022)

TY  - DATA
AU  - Jonović, Marko
AU  - Jugović, Branimir
AU  - Žuža, Milena
AU  - Đorđević, Verica
AU  - Milašinović, Nikola
AU  - Bugarski, Branko
AU  - Knežević-Jugović, Zorica
PY  - 2022
UR  - https://dais.sanu.ac.rs/123456789/13156
AB  - Figure S1: Effects on the decolorization process: HRP-MAB size (a) AB225, (b) AV109; MAG-alginate ratio (c) AB225, (d) AV109; initial HRP concentration (e) AB225, (f) AV109; HRP-MAB mass (g) AB225, (h) AV109; initial H2O2 concentration (i) AB225, (j) AV109 and initial dye concentration (k) AB225, (l) AV109; Table S1: Reaction conditions for the optimization of decolorization process of AB225 and AV109 color
PB  - MDPI AG
T2  - Polymers
T1  - Supplementary information for the article Jonović, Marko, Jugović, Branimir, Žuža, Milena, Đorđević, Verica, Milašinović, Nikola, Bugarski, Branko, Knežević-Jugović, Zorica, "Immobilization of Horseradish Peroxidase on Magnetite-Alginate Beads to Enable Effective Strong Binding and Enzyme Recycling during Anthraquinone Dyes’ Degradation" in Polymers, 14, no. 13 (2022):2614, https://doi.org/10.3390/polym14132614
VL  - 14
UR  - https://hdl.handle.net/21.15107/rcub_dais_13156
ER  - 
@misc{
author = "Jonović, Marko and Jugović, Branimir and Žuža, Milena and Đorđević, Verica and Milašinović, Nikola and Bugarski, Branko and Knežević-Jugović, Zorica",
year = "2022",
abstract = "Figure S1: Effects on the decolorization process: HRP-MAB size (a) AB225, (b) AV109; MAG-alginate ratio (c) AB225, (d) AV109; initial HRP concentration (e) AB225, (f) AV109; HRP-MAB mass (g) AB225, (h) AV109; initial H2O2 concentration (i) AB225, (j) AV109 and initial dye concentration (k) AB225, (l) AV109; Table S1: Reaction conditions for the optimization of decolorization process of AB225 and AV109 color",
publisher = "MDPI AG",
journal = "Polymers",
title = "Supplementary information for the article Jonović, Marko, Jugović, Branimir, Žuža, Milena, Đorđević, Verica, Milašinović, Nikola, Bugarski, Branko, Knežević-Jugović, Zorica, "Immobilization of Horseradish Peroxidase on Magnetite-Alginate Beads to Enable Effective Strong Binding and Enzyme Recycling during Anthraquinone Dyes’ Degradation" in Polymers, 14, no. 13 (2022):2614, https://doi.org/10.3390/polym14132614",
volume = "14",
url = "https://hdl.handle.net/21.15107/rcub_dais_13156"
}
Jonović, M., Jugović, B., Žuža, M., Đorđević, V., Milašinović, N., Bugarski, B.,& Knežević-Jugović, Z.. (2022). Supplementary information for the article Jonović, Marko, Jugović, Branimir, Žuža, Milena, Đorđević, Verica, Milašinović, Nikola, Bugarski, Branko, Knežević-Jugović, Zorica, "Immobilization of Horseradish Peroxidase on Magnetite-Alginate Beads to Enable Effective Strong Binding and Enzyme Recycling during Anthraquinone Dyes’ Degradation" in Polymers, 14, no. 13 (2022):2614, https://doi.org/10.3390/polym14132614. in Polymers
MDPI AG., 14.
https://hdl.handle.net/21.15107/rcub_dais_13156
Jonović M, Jugović B, Žuža M, Đorđević V, Milašinović N, Bugarski B, Knežević-Jugović Z. Supplementary information for the article Jonović, Marko, Jugović, Branimir, Žuža, Milena, Đorđević, Verica, Milašinović, Nikola, Bugarski, Branko, Knežević-Jugović, Zorica, "Immobilization of Horseradish Peroxidase on Magnetite-Alginate Beads to Enable Effective Strong Binding and Enzyme Recycling during Anthraquinone Dyes’ Degradation" in Polymers, 14, no. 13 (2022):2614, https://doi.org/10.3390/polym14132614. in Polymers. 2022;14.
https://hdl.handle.net/21.15107/rcub_dais_13156 .
Jonović, Marko, Jugović, Branimir, Žuža, Milena, Đorđević, Verica, Milašinović, Nikola, Bugarski, Branko, Knežević-Jugović, Zorica, "Supplementary information for the article Jonović, Marko, Jugović, Branimir, Žuža, Milena, Đorđević, Verica, Milašinović, Nikola, Bugarski, Branko, Knežević-Jugović, Zorica, "Immobilization of Horseradish Peroxidase on Magnetite-Alginate Beads to Enable Effective Strong Binding and Enzyme Recycling during Anthraquinone Dyes’ Degradation" in Polymers, 14, no. 13 (2022):2614, https://doi.org/10.3390/polym14132614" in Polymers, 14 (2022),
https://hdl.handle.net/21.15107/rcub_dais_13156 .

Removal of the As(V) and Cr(VI) from the Water Using Magnetite/3D-Printed Wollastonite Hybrid Adsorbent

Popović, Mina; Veličković, Zlate S.; Bogdanov, Jovica; Marinković, Aleksandar D.; Luna, Mariano Casas; Trajković, Isaak; Obradović, Nina; Pavlović, Vladimir B.

(International Institute for the Science of Sintering (IISS), 2022)

TY  - JOUR
AU  - Popović, Mina
AU  - Veličković, Zlate S.
AU  - Bogdanov, Jovica
AU  - Marinković, Aleksandar D.
AU  - Luna, Mariano Casas
AU  - Trajković, Isaak
AU  - Obradović, Nina
AU  - Pavlović, Vladimir B.
PY  - 2022
UR  - https://dais.sanu.ac.rs/123456789/12955
AB  - In this study, the structure, morphology and composition of the synthesized magnetite/3D-printed wollastonite (3D_W/M) composite were characterized, and its adsorption performance with respect to As(V) and Cr(VI) were studied. Magnetite (MG) modified 3D printed wollastonite was obtained by two step procedure: modification of 3D_W with 3-aminoproylsilane (APTES) followed by controlled magnetite (MG) deposition to obtain 3D_W/M adsorbent. The structure/properties of 3D_W/M were confirmed by applying FTIR, XRD, TGD/DTA, and SEM analysis. The adsorption properties of hybrid adsorbents were carried out for As(V) and Cr(VI) removal-one relative to the initial pH value, the adsorbent mass, the temperature, and the adsorption time. Time-dependent adsorption study was best described by pseudo-second order equation, while Weber Morris analysis showed that intraparticle diffusion controled diffusional transport. Similar activation energy, 17.44 and 14.49 kJ•mol-1 for adsorption As(V) and Cr(VI) on 3D_W/M, respectively, indicated main contribution of physical adsorption. Determination of adsorption parameters was performed by applying different adsorption isotherm models, and the best fit was obtained using Freundlich model. The adsorption capacity of 24.16 and 29.6 mg g-1 for As(V) and Cr(VI) at 2o C, Co = 5.5 and 5.3 mg L-1, respectively, were obtained. Thermodynamic study indicated favourable process at a higher temperature. Preliminary fixed-bed column study and results fitting with Bohart-Adams, Yoon-Nelson, Thomas, and Modified dose-response model showed good agreement with results from the batch study.
PB  - International Institute for the Science of Sintering (IISS)
T2  - Science of Sintering
T1  - Removal of the As(V) and Cr(VI) from the Water Using Magnetite/3D-Printed Wollastonite Hybrid Adsorbent
SP  - 105
EP  - 124
VL  - 54
IS  - 1
DO  - 10.2298/SOS2201105P
UR  - https://hdl.handle.net/21.15107/rcub_dais_12955
ER  - 
@article{
author = "Popović, Mina and Veličković, Zlate S. and Bogdanov, Jovica and Marinković, Aleksandar D. and Luna, Mariano Casas and Trajković, Isaak and Obradović, Nina and Pavlović, Vladimir B.",
year = "2022",
abstract = "In this study, the structure, morphology and composition of the synthesized magnetite/3D-printed wollastonite (3D_W/M) composite were characterized, and its adsorption performance with respect to As(V) and Cr(VI) were studied. Magnetite (MG) modified 3D printed wollastonite was obtained by two step procedure: modification of 3D_W with 3-aminoproylsilane (APTES) followed by controlled magnetite (MG) deposition to obtain 3D_W/M adsorbent. The structure/properties of 3D_W/M were confirmed by applying FTIR, XRD, TGD/DTA, and SEM analysis. The adsorption properties of hybrid adsorbents were carried out for As(V) and Cr(VI) removal-one relative to the initial pH value, the adsorbent mass, the temperature, and the adsorption time. Time-dependent adsorption study was best described by pseudo-second order equation, while Weber Morris analysis showed that intraparticle diffusion controled diffusional transport. Similar activation energy, 17.44 and 14.49 kJ•mol-1 for adsorption As(V) and Cr(VI) on 3D_W/M, respectively, indicated main contribution of physical adsorption. Determination of adsorption parameters was performed by applying different adsorption isotherm models, and the best fit was obtained using Freundlich model. The adsorption capacity of 24.16 and 29.6 mg g-1 for As(V) and Cr(VI) at 2o C, Co = 5.5 and 5.3 mg L-1, respectively, were obtained. Thermodynamic study indicated favourable process at a higher temperature. Preliminary fixed-bed column study and results fitting with Bohart-Adams, Yoon-Nelson, Thomas, and Modified dose-response model showed good agreement with results from the batch study.",
publisher = "International Institute for the Science of Sintering (IISS)",
journal = "Science of Sintering",
title = "Removal of the As(V) and Cr(VI) from the Water Using Magnetite/3D-Printed Wollastonite Hybrid Adsorbent",
pages = "105-124",
volume = "54",
number = "1",
doi = "10.2298/SOS2201105P",
url = "https://hdl.handle.net/21.15107/rcub_dais_12955"
}
Popović, M., Veličković, Z. S., Bogdanov, J., Marinković, A. D., Luna, M. C., Trajković, I., Obradović, N.,& Pavlović, V. B.. (2022). Removal of the As(V) and Cr(VI) from the Water Using Magnetite/3D-Printed Wollastonite Hybrid Adsorbent. in Science of Sintering
International Institute for the Science of Sintering (IISS)., 54(1), 105-124.
https://doi.org/10.2298/SOS2201105P
https://hdl.handle.net/21.15107/rcub_dais_12955
Popović M, Veličković ZS, Bogdanov J, Marinković AD, Luna MC, Trajković I, Obradović N, Pavlović VB. Removal of the As(V) and Cr(VI) from the Water Using Magnetite/3D-Printed Wollastonite Hybrid Adsorbent. in Science of Sintering. 2022;54(1):105-124.
doi:10.2298/SOS2201105P
https://hdl.handle.net/21.15107/rcub_dais_12955 .
Popović, Mina, Veličković, Zlate S., Bogdanov, Jovica, Marinković, Aleksandar D., Luna, Mariano Casas, Trajković, Isaak, Obradović, Nina, Pavlović, Vladimir B., "Removal of the As(V) and Cr(VI) from the Water Using Magnetite/3D-Printed Wollastonite Hybrid Adsorbent" in Science of Sintering, 54, no. 1 (2022):105-124,
https://doi.org/10.2298/SOS2201105P .,
https://hdl.handle.net/21.15107/rcub_dais_12955 .
1
1

Immobilization of Horseradish Peroxidase on Magnetite-Alginate Beads to Enable Effective Strong Binding and Enzyme Recycling during Anthraquinone Dyes’ Degradation

Jonović, Marko; Jugović, Branimir; Žuža, Milena; Đorđević, Verica; Milašinović, Nikola; Bugarski, Branko; Knežević-Jugović, Zorica

(MDPI AG, 2022)

TY  - JOUR
AU  - Jonović, Marko
AU  - Jugović, Branimir
AU  - Žuža, Milena
AU  - Đorđević, Verica
AU  - Milašinović, Nikola
AU  - Bugarski, Branko
AU  - Knežević-Jugović, Zorica
PY  - 2022
UR  - https://dais.sanu.ac.rs/123456789/13155
AB  - The aim of this study was to investigate covalent immobilization of horseradish peroxidase (HRP) on magnetic nanoparticles (Mag) encapsulated in calcium alginate beads (MABs) for color degradation, combining easy and fast removal of biocatalyst from the reaction mixture due to its magnetic properties and strong binding due to surface alginate functional groups. MABs obtained by extrusion techniques were analyzed by optical microscopy, FEG-SEM and characterized regarding mechanical properties, magnetization and HRP binding. HRP with initial concentration of 10 mg/gcarrier was successfully covalently bonded on MABs (diameter ~1 mm, magnetite/alginate ratio 1:4), with protein loading of 8.9 mg/gcarrier, immobilization yield 96.9% and activity 32.8 U/g. Immobilized HRP on MABs (HRP-MABs) was then used to catalyze degradation of two anthraquinonic dyes, Acid Blue 225 (AB225) and Acid Violet 109 (AV109), as models for wastewater pollutants. HRP-MABs decolorized 77.3% and 76.1% of AV109 and AB225, respectively after 15 min under optimal conditions (0.097 mM H2O2, 200 mg of HRP-MABs (8.9 mg/gcarrier), 0.08 and 0.1 g/mg beads/dye ratio for AV109 and AB225, respectively). Biocatalyst was used for 7 repeated cycles retaining 75% and 51% of initial activity for AB225 and AV109, respectively, showing potential for use in large scale applications for colored wastewater treatment.
PB  - MDPI AG
T2  - Polymers
T1  - Immobilization of Horseradish Peroxidase on Magnetite-Alginate Beads to Enable Effective Strong Binding and Enzyme Recycling during Anthraquinone Dyes’ Degradation
SP  - 2614
VL  - 14
IS  - 13
DO  - 10.3390/polym14132614
UR  - https://hdl.handle.net/21.15107/rcub_dais_13155
ER  - 
@article{
author = "Jonović, Marko and Jugović, Branimir and Žuža, Milena and Đorđević, Verica and Milašinović, Nikola and Bugarski, Branko and Knežević-Jugović, Zorica",
year = "2022",
abstract = "The aim of this study was to investigate covalent immobilization of horseradish peroxidase (HRP) on magnetic nanoparticles (Mag) encapsulated in calcium alginate beads (MABs) for color degradation, combining easy and fast removal of biocatalyst from the reaction mixture due to its magnetic properties and strong binding due to surface alginate functional groups. MABs obtained by extrusion techniques were analyzed by optical microscopy, FEG-SEM and characterized regarding mechanical properties, magnetization and HRP binding. HRP with initial concentration of 10 mg/gcarrier was successfully covalently bonded on MABs (diameter ~1 mm, magnetite/alginate ratio 1:4), with protein loading of 8.9 mg/gcarrier, immobilization yield 96.9% and activity 32.8 U/g. Immobilized HRP on MABs (HRP-MABs) was then used to catalyze degradation of two anthraquinonic dyes, Acid Blue 225 (AB225) and Acid Violet 109 (AV109), as models for wastewater pollutants. HRP-MABs decolorized 77.3% and 76.1% of AV109 and AB225, respectively after 15 min under optimal conditions (0.097 mM H2O2, 200 mg of HRP-MABs (8.9 mg/gcarrier), 0.08 and 0.1 g/mg beads/dye ratio for AV109 and AB225, respectively). Biocatalyst was used for 7 repeated cycles retaining 75% and 51% of initial activity for AB225 and AV109, respectively, showing potential for use in large scale applications for colored wastewater treatment.",
publisher = "MDPI AG",
journal = "Polymers",
title = "Immobilization of Horseradish Peroxidase on Magnetite-Alginate Beads to Enable Effective Strong Binding and Enzyme Recycling during Anthraquinone Dyes’ Degradation",
pages = "2614",
volume = "14",
number = "13",
doi = "10.3390/polym14132614",
url = "https://hdl.handle.net/21.15107/rcub_dais_13155"
}
Jonović, M., Jugović, B., Žuža, M., Đorđević, V., Milašinović, N., Bugarski, B.,& Knežević-Jugović, Z.. (2022). Immobilization of Horseradish Peroxidase on Magnetite-Alginate Beads to Enable Effective Strong Binding and Enzyme Recycling during Anthraquinone Dyes’ Degradation. in Polymers
MDPI AG., 14(13), 2614.
https://doi.org/10.3390/polym14132614
https://hdl.handle.net/21.15107/rcub_dais_13155
Jonović M, Jugović B, Žuža M, Đorđević V, Milašinović N, Bugarski B, Knežević-Jugović Z. Immobilization of Horseradish Peroxidase on Magnetite-Alginate Beads to Enable Effective Strong Binding and Enzyme Recycling during Anthraquinone Dyes’ Degradation. in Polymers. 2022;14(13):2614.
doi:10.3390/polym14132614
https://hdl.handle.net/21.15107/rcub_dais_13155 .
Jonović, Marko, Jugović, Branimir, Žuža, Milena, Đorđević, Verica, Milašinović, Nikola, Bugarski, Branko, Knežević-Jugović, Zorica, "Immobilization of Horseradish Peroxidase on Magnetite-Alginate Beads to Enable Effective Strong Binding and Enzyme Recycling during Anthraquinone Dyes’ Degradation" in Polymers, 14, no. 13 (2022):2614,
https://doi.org/10.3390/polym14132614 .,
https://hdl.handle.net/21.15107/rcub_dais_13155 .

Influence of chloride ion concentration on initial corrosion of AZ63 magnesium alloy

Grgur, Branimir; Jugović, Branimir; Gvozdenović, Milica M.

(Nonferrous Metals Society of China, 2022)

TY  - JOUR
AU  - Grgur, Branimir
AU  - Jugović, Branimir
AU  - Gvozdenović, Milica M.
PY  - 2022
UR  - https://dais.sanu.ac.rs/123456789/13013
AB  - The initial corrosion behavior of AZ63 magnesium alloy was investigated in 1, 3, 5 and 7 wt.% NaCl solutions by means of corrosion potential, linear polarization, electrochemical impedance spectroscopy, and polarization measurements, during exposure in the corrosion media. Results show that the increase in chloride concentration provokes an increase in the corrosion rate. Based on the obtained kinetics parameters the mechanisms of anodic dissolution and hydrogen evolution reactions were discussed, and kinetic models were proposed. It is concluded that anodic dissolution proceeds under Temkin conditions and hydrogen evolution reaction depends on the surface coverage of Mg(OH)2 species.
PB  - Nonferrous Metals Society of China
T2  - Transactions of Nonferrous Metals Society of China (English Edition)
T1  - Influence of chloride ion concentration on initial corrosion of AZ63 magnesium alloy
SP  - 1133
EP  - 1143
VL  - 32
IS  - 4
DO  - 10.1016/S1003-6326(22)65861-8
UR  - https://hdl.handle.net/21.15107/rcub_dais_13013
ER  - 
@article{
author = "Grgur, Branimir and Jugović, Branimir and Gvozdenović, Milica M.",
year = "2022",
abstract = "The initial corrosion behavior of AZ63 magnesium alloy was investigated in 1, 3, 5 and 7 wt.% NaCl solutions by means of corrosion potential, linear polarization, electrochemical impedance spectroscopy, and polarization measurements, during exposure in the corrosion media. Results show that the increase in chloride concentration provokes an increase in the corrosion rate. Based on the obtained kinetics parameters the mechanisms of anodic dissolution and hydrogen evolution reactions were discussed, and kinetic models were proposed. It is concluded that anodic dissolution proceeds under Temkin conditions and hydrogen evolution reaction depends on the surface coverage of Mg(OH)2 species.",
publisher = "Nonferrous Metals Society of China",
journal = "Transactions of Nonferrous Metals Society of China (English Edition)",
title = "Influence of chloride ion concentration on initial corrosion of AZ63 magnesium alloy",
pages = "1133-1143",
volume = "32",
number = "4",
doi = "10.1016/S1003-6326(22)65861-8",
url = "https://hdl.handle.net/21.15107/rcub_dais_13013"
}
Grgur, B., Jugović, B.,& Gvozdenović, M. M.. (2022). Influence of chloride ion concentration on initial corrosion of AZ63 magnesium alloy. in Transactions of Nonferrous Metals Society of China (English Edition)
Nonferrous Metals Society of China., 32(4), 1133-1143.
https://doi.org/10.1016/S1003-6326(22)65861-8
https://hdl.handle.net/21.15107/rcub_dais_13013
Grgur B, Jugović B, Gvozdenović MM. Influence of chloride ion concentration on initial corrosion of AZ63 magnesium alloy. in Transactions of Nonferrous Metals Society of China (English Edition). 2022;32(4):1133-1143.
doi:10.1016/S1003-6326(22)65861-8
https://hdl.handle.net/21.15107/rcub_dais_13013 .
Grgur, Branimir, Jugović, Branimir, Gvozdenović, Milica M., "Influence of chloride ion concentration on initial corrosion of AZ63 magnesium alloy" in Transactions of Nonferrous Metals Society of China (English Edition), 32, no. 4 (2022):1133-1143,
https://doi.org/10.1016/S1003-6326(22)65861-8 .,
https://hdl.handle.net/21.15107/rcub_dais_13013 .

TiO2 nanotubes film/FTO glass interface: Thermal treatment effects

Vujančević, Jelena; Bjelajac, Anđelika; Veltruska, Katerina; Matolin, Vladimir; Siketić, Zdravko; Provatas, Georgios; Jakšić, Milko; Stan, George; Socol, Gabriel; Mihailescu, Ion; Pavlović, Vladimir B.; Janaćkovic, Đorđe

(ETRAN, 2022)

TY  - JOUR
AU  - Vujančević, Jelena
AU  - Bjelajac, Anđelika
AU  - Veltruska, Katerina
AU  - Matolin, Vladimir
AU  - Siketić, Zdravko
AU  - Provatas, Georgios
AU  - Jakšić, Milko
AU  - Stan, George
AU  - Socol, Gabriel
AU  - Mihailescu, Ion
AU  - Pavlović, Vladimir B.
AU  - Janaćkovic, Đorđe
PY  - 2022
UR  - https://dais.sanu.ac.rs/123456789/13160
AB  - Pure Ti films deposited by radio-frequency magnetron sputtering on FTO glass were anodized to fabricate TiO2 nanotubes (NTs) arrays. The TiO2 NTs/FTO samples were sintered at 450, 550 and 630°C, in ambient air. The thermal treatment did not influence the crystal phase composition, preserving in all cases the anatase single phase. As expected, the crystalline anatase quality improved with the annealing temperature. Nevertheless, slight differences in nanotubular morphology, such as the appearance of grains inside the walls, were observed in the case of the sample sintered at 630°C. Chemical analysis by X-ray Photoelectron Spectroscopy of annealed samples revealed the presence of Sn inside TiO2 NTs, due to diffusion of Sn from the substrate to TiO2. For the substrate was used FTO glass whose top layer consists of SnO2 doped with F. Rutherford Backscattering Spectrometry and Time-of-Flight Elastic Recoil Detection Analysis were carried out to study the elemental depth profile of the films. It was found that the temperature of sintering controls the Sn diffusion inside TiO2 film. Sn atoms diffuse towards the TiO2 NTs surface for the samples annealed at 450 and 550°C. The diffusion is however hindered in the case of the heat treatment at 630°C. Besides, the Ti diffusion into the SnO2 underlayer was observed, together with the formation of TiO2/SnO2 interfaces. One then expected but not a great difference in absorption between samples, since all contained anatase phase, as confirmed by Diffuse Reflectance Spectroscopy. A higher amount of Sn was however detected for the sample annealed at 550°C, which accounts for a slight red absorption shift. The importance of controlling the annealing parameters of the anodized TiO2/FTO structures was highlighted through the formation of TiO2-SnO2 interfaces and the Sn insertion from FTO, which can play an essential role in increasing the photoperformances of TiO2 NTs/FTO based structures of photovoltaic cells.
PB  - ETRAN
T2  - Science of Sintering
T1  - TiO2 nanotubes film/FTO glass interface: Thermal treatment effects
SP  - 235
EP  - 248
VL  - 54
IS  - 2
DO  - 10.2298/SOS2202235V
UR  - https://hdl.handle.net/21.15107/rcub_dais_13160
ER  - 
@article{
author = "Vujančević, Jelena and Bjelajac, Anđelika and Veltruska, Katerina and Matolin, Vladimir and Siketić, Zdravko and Provatas, Georgios and Jakšić, Milko and Stan, George and Socol, Gabriel and Mihailescu, Ion and Pavlović, Vladimir B. and Janaćkovic, Đorđe",
year = "2022",
abstract = "Pure Ti films deposited by radio-frequency magnetron sputtering on FTO glass were anodized to fabricate TiO2 nanotubes (NTs) arrays. The TiO2 NTs/FTO samples were sintered at 450, 550 and 630°C, in ambient air. The thermal treatment did not influence the crystal phase composition, preserving in all cases the anatase single phase. As expected, the crystalline anatase quality improved with the annealing temperature. Nevertheless, slight differences in nanotubular morphology, such as the appearance of grains inside the walls, were observed in the case of the sample sintered at 630°C. Chemical analysis by X-ray Photoelectron Spectroscopy of annealed samples revealed the presence of Sn inside TiO2 NTs, due to diffusion of Sn from the substrate to TiO2. For the substrate was used FTO glass whose top layer consists of SnO2 doped with F. Rutherford Backscattering Spectrometry and Time-of-Flight Elastic Recoil Detection Analysis were carried out to study the elemental depth profile of the films. It was found that the temperature of sintering controls the Sn diffusion inside TiO2 film. Sn atoms diffuse towards the TiO2 NTs surface for the samples annealed at 450 and 550°C. The diffusion is however hindered in the case of the heat treatment at 630°C. Besides, the Ti diffusion into the SnO2 underlayer was observed, together with the formation of TiO2/SnO2 interfaces. One then expected but not a great difference in absorption between samples, since all contained anatase phase, as confirmed by Diffuse Reflectance Spectroscopy. A higher amount of Sn was however detected for the sample annealed at 550°C, which accounts for a slight red absorption shift. The importance of controlling the annealing parameters of the anodized TiO2/FTO structures was highlighted through the formation of TiO2-SnO2 interfaces and the Sn insertion from FTO, which can play an essential role in increasing the photoperformances of TiO2 NTs/FTO based structures of photovoltaic cells.",
publisher = "ETRAN",
journal = "Science of Sintering",
title = "TiO2 nanotubes film/FTO glass interface: Thermal treatment effects",
pages = "235-248",
volume = "54",
number = "2",
doi = "10.2298/SOS2202235V",
url = "https://hdl.handle.net/21.15107/rcub_dais_13160"
}
Vujančević, J., Bjelajac, A., Veltruska, K., Matolin, V., Siketić, Z., Provatas, G., Jakšić, M., Stan, G., Socol, G., Mihailescu, I., Pavlović, V. B.,& Janaćkovic, Đ.. (2022). TiO2 nanotubes film/FTO glass interface: Thermal treatment effects. in Science of Sintering
ETRAN., 54(2), 235-248.
https://doi.org/10.2298/SOS2202235V
https://hdl.handle.net/21.15107/rcub_dais_13160
Vujančević J, Bjelajac A, Veltruska K, Matolin V, Siketić Z, Provatas G, Jakšić M, Stan G, Socol G, Mihailescu I, Pavlović VB, Janaćkovic Đ. TiO2 nanotubes film/FTO glass interface: Thermal treatment effects. in Science of Sintering. 2022;54(2):235-248.
doi:10.2298/SOS2202235V
https://hdl.handle.net/21.15107/rcub_dais_13160 .
Vujančević, Jelena, Bjelajac, Anđelika, Veltruska, Katerina, Matolin, Vladimir, Siketić, Zdravko, Provatas, Georgios, Jakšić, Milko, Stan, George, Socol, Gabriel, Mihailescu, Ion, Pavlović, Vladimir B., Janaćkovic, Đorđe, "TiO2 nanotubes film/FTO glass interface: Thermal treatment effects" in Science of Sintering, 54, no. 2 (2022):235-248,
https://doi.org/10.2298/SOS2202235V .,
https://hdl.handle.net/21.15107/rcub_dais_13160 .

New environmentally acceptable materials based on flay ash, steelmaking slag and Zn-reach electric arc furnace dust

Nikolić, Irena; Đurović, Dijana; Marković, Smilja; Veselinović, Ljiljana; Janković, Ivona; Radmilović, Vuk V.; Radmilović, Velimir R.

(Belgrade : Materials Research Society of Serbia, 2021)

TY  - CONF
AU  - Nikolić, Irena
AU  - Đurović, Dijana
AU  - Marković, Smilja
AU  - Veselinović, Ljiljana
AU  - Janković, Ivona
AU  - Radmilović, Vuk V.
AU  - Radmilović, Velimir R.
PY  - 2021
UR  - https://dais.sanu.ac.rs/123456789/12074
AB  - The newer methods of electric arc furnace dust (EAFD) valorisation include its stabilization into materials which potentially can be used in construction. This is the most promising method because of the low costs and waste reduction. The purpose of these study was to investigate the properties of alkali activated cement (AAC) based on fly ash (FA) or steelmaking electric arc furnace slag (EAFS) as an agent fora stabilization/solidification of EAFD. The control type of AAC samples were prepared by mixing of solid precursor (FA or EAFS) with a mixture of 10 M NaOH and Na2SiO3 solutions followed by curing at in the oven for 48 h at 65 C. The samples of AAC doped with EAFD were prepared at the same conditions but the EAFD was added to the starting mixtures with FA in quantities of 10, 20 and 30% of total solid phase and 1, 2, 5 and 7 % of total EAFS solid phase. The results have shown that both, FA and EAFS can be successfully used as an agent for EAFD stabilization. AAC samples based of FA and EAFS exhibited strength which is suitable for both, landfill and construction applications. Stabilization of EAFD into the AAC matrix occurred by chemical and physical immobilization. Chemical immobilization of Zn into the reaction product of FA and EAFS alkali activation was confirmed by SEM/EDS investigations. The leaching of Zn from both, AAC matrix based on FA and EAFS is inferior in comparison to pristine EAFD and met the criteria for granular waste disposal at landfills for non-hazardous waste according the EN 12457-2 test.
PB  - Belgrade : Materials Research Society of Serbia
C3  - Programme and the Book of abstracts / Twenty-second Annual Conference YUCOMAT 2021 Herceg Novi, Montenegro, August 30 - September 3, 2021
T1  - New environmentally acceptable materials based on flay ash, steelmaking slag and Zn-reach electric arc furnace dust
T1  - New environmentally acceptable materials based on fly ash, steelmaking slag and Zn-reach electric arc furnace dust
SP  - 114
EP  - 114
UR  - https://hdl.handle.net/21.15107/rcub_dais_12074
ER  - 
@conference{
author = "Nikolić, Irena and Đurović, Dijana and Marković, Smilja and Veselinović, Ljiljana and Janković, Ivona and Radmilović, Vuk V. and Radmilović, Velimir R.",
year = "2021",
abstract = "The newer methods of electric arc furnace dust (EAFD) valorisation include its stabilization into materials which potentially can be used in construction. This is the most promising method because of the low costs and waste reduction. The purpose of these study was to investigate the properties of alkali activated cement (AAC) based on fly ash (FA) or steelmaking electric arc furnace slag (EAFS) as an agent fora stabilization/solidification of EAFD. The control type of AAC samples were prepared by mixing of solid precursor (FA or EAFS) with a mixture of 10 M NaOH and Na2SiO3 solutions followed by curing at in the oven for 48 h at 65 C. The samples of AAC doped with EAFD were prepared at the same conditions but the EAFD was added to the starting mixtures with FA in quantities of 10, 20 and 30% of total solid phase and 1, 2, 5 and 7 % of total EAFS solid phase. The results have shown that both, FA and EAFS can be successfully used as an agent for EAFD stabilization. AAC samples based of FA and EAFS exhibited strength which is suitable for both, landfill and construction applications. Stabilization of EAFD into the AAC matrix occurred by chemical and physical immobilization. Chemical immobilization of Zn into the reaction product of FA and EAFS alkali activation was confirmed by SEM/EDS investigations. The leaching of Zn from both, AAC matrix based on FA and EAFS is inferior in comparison to pristine EAFD and met the criteria for granular waste disposal at landfills for non-hazardous waste according the EN 12457-2 test.",
publisher = "Belgrade : Materials Research Society of Serbia",
journal = "Programme and the Book of abstracts / Twenty-second Annual Conference YUCOMAT 2021 Herceg Novi, Montenegro, August 30 - September 3, 2021",
title = "New environmentally acceptable materials based on flay ash, steelmaking slag and Zn-reach electric arc furnace dust, New environmentally acceptable materials based on fly ash, steelmaking slag and Zn-reach electric arc furnace dust",
pages = "114-114",
url = "https://hdl.handle.net/21.15107/rcub_dais_12074"
}
Nikolić, I., Đurović, D., Marković, S., Veselinović, L., Janković, I., Radmilović, V. V.,& Radmilović, V. R.. (2021). New environmentally acceptable materials based on flay ash, steelmaking slag and Zn-reach electric arc furnace dust. in Programme and the Book of abstracts / Twenty-second Annual Conference YUCOMAT 2021 Herceg Novi, Montenegro, August 30 - September 3, 2021
Belgrade : Materials Research Society of Serbia., 114-114.
https://hdl.handle.net/21.15107/rcub_dais_12074
Nikolić I, Đurović D, Marković S, Veselinović L, Janković I, Radmilović VV, Radmilović VR. New environmentally acceptable materials based on flay ash, steelmaking slag and Zn-reach electric arc furnace dust. in Programme and the Book of abstracts / Twenty-second Annual Conference YUCOMAT 2021 Herceg Novi, Montenegro, August 30 - September 3, 2021. 2021;:114-114.
https://hdl.handle.net/21.15107/rcub_dais_12074 .
Nikolić, Irena, Đurović, Dijana, Marković, Smilja, Veselinović, Ljiljana, Janković, Ivona, Radmilović, Vuk V., Radmilović, Velimir R., "New environmentally acceptable materials based on flay ash, steelmaking slag and Zn-reach electric arc furnace dust" in Programme and the Book of abstracts / Twenty-second Annual Conference YUCOMAT 2021 Herceg Novi, Montenegro, August 30 - September 3, 2021 (2021):114-114,
https://hdl.handle.net/21.15107/rcub_dais_12074 .

Nonlinear laser scanning microscopy for imaging of the cells labeled by upconverting NaYF4:Yb,Er nanoparticles

Rabasović, Mihailo D.; Dinić, Ivana; Đukić Vuković, Aleksandra; Lazarević, Miloš; Nikolić, Marko G.; Krmpot, Aleksandar; Mančić, Lidija

(Belgrade : Serbian Ceramic Society, 2021)

TY  - CONF
AU  - Rabasović, Mihailo D.
AU  - Dinić, Ivana
AU  - Đukić Vuković, Aleksandra
AU  - Lazarević, Miloš
AU  - Nikolić, Marko G.
AU  - Krmpot, Aleksandar
AU  - Mančić, Lidija
PY  - 2021
UR  - https://dais.sanu.ac.rs/123456789/11912
AB  - The Nonlinear Laser Scanning Microscopy (NLSM) contributes to the cell labeling through addressing two main issues: photobleaching and phototoxicity. Moreover, an increase of the penetration depth and a reduction of background autofluorescence are achieved.We have used a multidisciplinary approach combining expertise in material science, nanoparticles synthesis and characterization, cancer cell and tissue labeling, and high resolution imaging, in order to accomplish in vitro imaging of the cancer cells. We have imaged the oral squamous carcinoma cells and human gingival cells. We have demonstrated that we are able to take high contrast images. We have shown position of the nanoparticles in cells, through colocalization of the cell auto-fluorescence and the nanoparticles up-conversion.We plan to improve our abilities through further optimization of the up-converting nanoparticles (smaller and brighter particles) and microscopy technique.
PB  - Belgrade : Serbian Ceramic Society
C3  - Program and the Book of abstracts / Serbian Ceramic Society Conference Advanced Ceramics and Application IX : New Frontiers in Multifunctional Material Science and Processing, Serbia, Belgrade, 20-21. September 2021, 2021, 36-36
T1  - Nonlinear laser scanning microscopy for imaging of the cells labeled by upconverting NaYF4:Yb,Er nanoparticles
SP  - 35
EP  - 35
UR  - https://hdl.handle.net/21.15107/rcub_dais_11912
ER  - 
@conference{
author = "Rabasović, Mihailo D. and Dinić, Ivana and Đukić Vuković, Aleksandra and Lazarević, Miloš and Nikolić, Marko G. and Krmpot, Aleksandar and Mančić, Lidija",
year = "2021",
abstract = "The Nonlinear Laser Scanning Microscopy (NLSM) contributes to the cell labeling through addressing two main issues: photobleaching and phototoxicity. Moreover, an increase of the penetration depth and a reduction of background autofluorescence are achieved.We have used a multidisciplinary approach combining expertise in material science, nanoparticles synthesis and characterization, cancer cell and tissue labeling, and high resolution imaging, in order to accomplish in vitro imaging of the cancer cells. We have imaged the oral squamous carcinoma cells and human gingival cells. We have demonstrated that we are able to take high contrast images. We have shown position of the nanoparticles in cells, through colocalization of the cell auto-fluorescence and the nanoparticles up-conversion.We plan to improve our abilities through further optimization of the up-converting nanoparticles (smaller and brighter particles) and microscopy technique.",
publisher = "Belgrade : Serbian Ceramic Society",
journal = "Program and the Book of abstracts / Serbian Ceramic Society Conference Advanced Ceramics and Application IX : New Frontiers in Multifunctional Material Science and Processing, Serbia, Belgrade, 20-21. September 2021, 2021, 36-36",
title = "Nonlinear laser scanning microscopy for imaging of the cells labeled by upconverting NaYF4:Yb,Er nanoparticles",
pages = "35-35",
url = "https://hdl.handle.net/21.15107/rcub_dais_11912"
}
Rabasović, M. D., Dinić, I., Đukić Vuković, A., Lazarević, M., Nikolić, M. G., Krmpot, A.,& Mančić, L.. (2021). Nonlinear laser scanning microscopy for imaging of the cells labeled by upconverting NaYF4:Yb,Er nanoparticles. in Program and the Book of abstracts / Serbian Ceramic Society Conference Advanced Ceramics and Application IX : New Frontiers in Multifunctional Material Science and Processing, Serbia, Belgrade, 20-21. September 2021, 2021, 36-36
Belgrade : Serbian Ceramic Society., 35-35.
https://hdl.handle.net/21.15107/rcub_dais_11912
Rabasović MD, Dinić I, Đukić Vuković A, Lazarević M, Nikolić MG, Krmpot A, Mančić L. Nonlinear laser scanning microscopy for imaging of the cells labeled by upconverting NaYF4:Yb,Er nanoparticles. in Program and the Book of abstracts / Serbian Ceramic Society Conference Advanced Ceramics and Application IX : New Frontiers in Multifunctional Material Science and Processing, Serbia, Belgrade, 20-21. September 2021, 2021, 36-36. 2021;:35-35.
https://hdl.handle.net/21.15107/rcub_dais_11912 .
Rabasović, Mihailo D., Dinić, Ivana, Đukić Vuković, Aleksandra, Lazarević, Miloš, Nikolić, Marko G., Krmpot, Aleksandar, Mančić, Lidija, "Nonlinear laser scanning microscopy for imaging of the cells labeled by upconverting NaYF4:Yb,Er nanoparticles" in Program and the Book of abstracts / Serbian Ceramic Society Conference Advanced Ceramics and Application IX : New Frontiers in Multifunctional Material Science and Processing, Serbia, Belgrade, 20-21. September 2021, 2021, 36-36 (2021):35-35,
https://hdl.handle.net/21.15107/rcub_dais_11912 .

Freeze versus Spray Drying for Dry Wild Thyme (Thymus serpyllum L.) Extract Formulations: The Impact of Gelatin as a Coating Material

Jovanović, Aleksandra A.; Lević, Steva; Pavlović, Vladimir B.; Marković, Smilja; Pjanović, Rada; Đorđević, Verica B.; Nedović, Viktor; Bugarski, Branko

(2021)

TY  - GEN
AU  - Jovanović, Aleksandra A.
AU  - Lević, Steva
AU  - Pavlović, Vladimir B.
AU  - Marković, Smilja
AU  - Pjanović, Rada
AU  - Đorđević, Verica B.
AU  - Nedović, Viktor
AU  - Bugarski, Branko
PY  - 2021
UR  - https://dais.sanu.ac.rs/123456789/11637
AB  - Freeze drying was compared with spray drying regarding feasibility to process wild thyme drug in order to obtain dry formulations at laboratory scale starting from liquid extracts produced by different extraction methods: maceration, heat-, ultrasound-, and microwave-assisted extractions. Higher powder yield (based on the dry weight prior to extraction) was achieved by freeze than spray drying and lower loss of total polyphenol content (TPC) and total flavonoid content (TFC) due to the drying process. Gelatin as a coating agent (5% w/w) provided better TPC recovery by 70% in case of lyophilization and higher powder yield in case of spray drying by diminishing material deposition on the wall of the drying chamber. The resulting gelatin-free and gelatin-containing powders carried polyphenols in amount ~190 and 53-75 mg gallic acid equivalents GAE/g of powder, respectively. Microwave-assisted extract formulation distinguished from others by higher content of polyphenols, proteins and sugars, higher bulk density and lower solubility. The type of the drying process affected mainly position of the gelatin-derived -OH and amide bands in FTIR spectra. Spray dried formulations compared to freeze dried expressed higher thermal stability as confirmed by differential scanning calorimetry analysis and higher diffusion coefficient; the last feature can be associated with the lower specific surface area of irregularly shaped freeze-dried particles (151-223 µm) compared to small microspheres (~8 µm) in spray-dried powder.
T2  - Preprints
T1  - Freeze versus Spray Drying for Dry Wild Thyme (Thymus serpyllum L.) Extract Formulations: The Impact of Gelatin as a Coating Material
DO  - 10.20944/preprints202105.0358.v1
UR  - https://hdl.handle.net/21.15107/rcub_dais_11637
ER  - 
@misc{
author = "Jovanović, Aleksandra A. and Lević, Steva and Pavlović, Vladimir B. and Marković, Smilja and Pjanović, Rada and Đorđević, Verica B. and Nedović, Viktor and Bugarski, Branko",
year = "2021",
abstract = "Freeze drying was compared with spray drying regarding feasibility to process wild thyme drug in order to obtain dry formulations at laboratory scale starting from liquid extracts produced by different extraction methods: maceration, heat-, ultrasound-, and microwave-assisted extractions. Higher powder yield (based on the dry weight prior to extraction) was achieved by freeze than spray drying and lower loss of total polyphenol content (TPC) and total flavonoid content (TFC) due to the drying process. Gelatin as a coating agent (5% w/w) provided better TPC recovery by 70% in case of lyophilization and higher powder yield in case of spray drying by diminishing material deposition on the wall of the drying chamber. The resulting gelatin-free and gelatin-containing powders carried polyphenols in amount ~190 and 53-75 mg gallic acid equivalents GAE/g of powder, respectively. Microwave-assisted extract formulation distinguished from others by higher content of polyphenols, proteins and sugars, higher bulk density and lower solubility. The type of the drying process affected mainly position of the gelatin-derived -OH and amide bands in FTIR spectra. Spray dried formulations compared to freeze dried expressed higher thermal stability as confirmed by differential scanning calorimetry analysis and higher diffusion coefficient; the last feature can be associated with the lower specific surface area of irregularly shaped freeze-dried particles (151-223 µm) compared to small microspheres (~8 µm) in spray-dried powder.",
journal = "Preprints",
title = "Freeze versus Spray Drying for Dry Wild Thyme (Thymus serpyllum L.) Extract Formulations: The Impact of Gelatin as a Coating Material",
doi = "10.20944/preprints202105.0358.v1",
url = "https://hdl.handle.net/21.15107/rcub_dais_11637"
}
Jovanović, A. A., Lević, S., Pavlović, V. B., Marković, S., Pjanović, R., Đorđević, V. B., Nedović, V.,& Bugarski, B.. (2021). Freeze versus Spray Drying for Dry Wild Thyme (Thymus serpyllum L.) Extract Formulations: The Impact of Gelatin as a Coating Material. in Preprints.
https://doi.org/10.20944/preprints202105.0358.v1
https://hdl.handle.net/21.15107/rcub_dais_11637
Jovanović AA, Lević S, Pavlović VB, Marković S, Pjanović R, Đorđević VB, Nedović V, Bugarski B. Freeze versus Spray Drying for Dry Wild Thyme (Thymus serpyllum L.) Extract Formulations: The Impact of Gelatin as a Coating Material. in Preprints. 2021;.
doi:10.20944/preprints202105.0358.v1
https://hdl.handle.net/21.15107/rcub_dais_11637 .
Jovanović, Aleksandra A., Lević, Steva, Pavlović, Vladimir B., Marković, Smilja, Pjanović, Rada, Đorđević, Verica B., Nedović, Viktor, Bugarski, Branko, "Freeze versus Spray Drying for Dry Wild Thyme (Thymus serpyllum L.) Extract Formulations: The Impact of Gelatin as a Coating Material" in Preprints (2021),
https://doi.org/10.20944/preprints202105.0358.v1 .,
https://hdl.handle.net/21.15107/rcub_dais_11637 .
1
2

2D and 3D silver-based coordination polymers with thiomorpholine-4-carbonitrile and piperazine-1,4-dicarbonitrile: structure, intermolecular interactions, photocatalysis, and thermal behavior

Ristić, Predrag; Filipović, Nenad; Blagojević, Vladimir A.; Ćirković, Jovana; Holló, Berta Barta; Đokić, Veljko R.; Donnard, Morgan; Gulea, Mihaela; Marjanović, Ivana; Klisurić, Olivera R.; Todorović, Tamara R.

(Royal Society of Chemistry (RSC), 2021)

TY  - JOUR
AU  - Ristić, Predrag
AU  - Filipović, Nenad
AU  - Blagojević, Vladimir A.
AU  - Ćirković, Jovana
AU  - Holló, Berta Barta
AU  - Đokić, Veljko R.
AU  - Donnard, Morgan
AU  - Gulea, Mihaela
AU  - Marjanović, Ivana
AU  - Klisurić, Olivera R.
AU  - Todorović, Tamara R.
PY  - 2021
UR  - https://dais.sanu.ac.rs/123456789/11753
AB  - Four silver-based coordination polymers, {[Ag(L1)2]NO3}∞ (1), {[Ag(L1)2]ClO4}∞ (2), {[Ag(L2)2]NO3·H2O}∞ (3) and {[Ag(L2)2]ClO4}∞ (4), were synthesized using the thiomorpholine-4-carbonitrile (L1) and piperazine-1,4-dicarbonitrile (L2) ligands. Compounds 1 and 2 are two-dimensional, while 3 and 4 are three-dimensional. L1 and L2 are 1,4-bis-monodentate ligands in all compounds, while Ag(I) ions are four-coordinated in a slightly distorted tetrahedral geometry. Topological analysis in standard representations suggests that underlying nets in 1 and 2 have an sql topology, while 3 and 4 exhibit a dia topology. Thermal analysis shows that 3 loses crystalline water at room temperature, while other compounds show good thermal stability. All compounds show good photocatalytic activity for photocatalytic degradation of the mordant blue 9 dye, with reaction rates in the range 0.029 to 0.061 min−1. The best result was obtained for compound 4, which can be correlated to its largest lattice volume.
PB  - Royal Society of Chemistry (RSC)
T2  - CrystEngComm
T1  - 2D and 3D silver-based coordination polymers with thiomorpholine-4-carbonitrile and piperazine-1,4-dicarbonitrile: structure, intermolecular interactions, photocatalysis, and thermal behavior
SP  - 4799
EP  - 4815
VL  - 23
IS  - 27
DO  - 10.1039/D1CE00394A
UR  - https://hdl.handle.net/21.15107/rcub_dais_11753
ER  - 
@article{
author = "Ristić, Predrag and Filipović, Nenad and Blagojević, Vladimir A. and Ćirković, Jovana and Holló, Berta Barta and Đokić, Veljko R. and Donnard, Morgan and Gulea, Mihaela and Marjanović, Ivana and Klisurić, Olivera R. and Todorović, Tamara R.",
year = "2021",
abstract = "Four silver-based coordination polymers, {[Ag(L1)2]NO3}∞ (1), {[Ag(L1)2]ClO4}∞ (2), {[Ag(L2)2]NO3·H2O}∞ (3) and {[Ag(L2)2]ClO4}∞ (4), were synthesized using the thiomorpholine-4-carbonitrile (L1) and piperazine-1,4-dicarbonitrile (L2) ligands. Compounds 1 and 2 are two-dimensional, while 3 and 4 are three-dimensional. L1 and L2 are 1,4-bis-monodentate ligands in all compounds, while Ag(I) ions are four-coordinated in a slightly distorted tetrahedral geometry. Topological analysis in standard representations suggests that underlying nets in 1 and 2 have an sql topology, while 3 and 4 exhibit a dia topology. Thermal analysis shows that 3 loses crystalline water at room temperature, while other compounds show good thermal stability. All compounds show good photocatalytic activity for photocatalytic degradation of the mordant blue 9 dye, with reaction rates in the range 0.029 to 0.061 min−1. The best result was obtained for compound 4, which can be correlated to its largest lattice volume.",
publisher = "Royal Society of Chemistry (RSC)",
journal = "CrystEngComm",
title = "2D and 3D silver-based coordination polymers with thiomorpholine-4-carbonitrile and piperazine-1,4-dicarbonitrile: structure, intermolecular interactions, photocatalysis, and thermal behavior",
pages = "4799-4815",
volume = "23",
number = "27",
doi = "10.1039/D1CE00394A",
url = "https://hdl.handle.net/21.15107/rcub_dais_11753"
}
Ristić, P., Filipović, N., Blagojević, V. A., Ćirković, J., Holló, B. B., Đokić, V. R., Donnard, M., Gulea, M., Marjanović, I., Klisurić, O. R.,& Todorović, T. R.. (2021). 2D and 3D silver-based coordination polymers with thiomorpholine-4-carbonitrile and piperazine-1,4-dicarbonitrile: structure, intermolecular interactions, photocatalysis, and thermal behavior. in CrystEngComm
Royal Society of Chemistry (RSC)., 23(27), 4799-4815.
https://doi.org/10.1039/D1CE00394A
https://hdl.handle.net/21.15107/rcub_dais_11753
Ristić P, Filipović N, Blagojević VA, Ćirković J, Holló BB, Đokić VR, Donnard M, Gulea M, Marjanović I, Klisurić OR, Todorović TR. 2D and 3D silver-based coordination polymers with thiomorpholine-4-carbonitrile and piperazine-1,4-dicarbonitrile: structure, intermolecular interactions, photocatalysis, and thermal behavior. in CrystEngComm. 2021;23(27):4799-4815.
doi:10.1039/D1CE00394A
https://hdl.handle.net/21.15107/rcub_dais_11753 .
Ristić, Predrag, Filipović, Nenad, Blagojević, Vladimir A., Ćirković, Jovana, Holló, Berta Barta, Đokić, Veljko R., Donnard, Morgan, Gulea, Mihaela, Marjanović, Ivana, Klisurić, Olivera R., Todorović, Tamara R., "2D and 3D silver-based coordination polymers with thiomorpholine-4-carbonitrile and piperazine-1,4-dicarbonitrile: structure, intermolecular interactions, photocatalysis, and thermal behavior" in CrystEngComm, 23, no. 27 (2021):4799-4815,
https://doi.org/10.1039/D1CE00394A .,
https://hdl.handle.net/21.15107/rcub_dais_11753 .
3
4
3

2D and 3D silver-based coordination polymers with thiomorpholine-4-carbonitrile and piperazine-1,4-dicarbonitrile: structure, intermolecular interactions, photocatalysis, and thermal behavior

Ristić, Predrag; Filipović, Nenad; Blagojević, Vladimir A.; Ćirković, Jovana; Holló, Berta Barta; Đokić, Veljko R.; Donnard, Morgan; Gulea, Mihaela; Marjanović, Ivana; Klisurić, Olivera R.; Todorović, Tamara R.

(Royal Society of Chemistry (RSC), 2021)

TY  - JOUR
AU  - Ristić, Predrag
AU  - Filipović, Nenad
AU  - Blagojević, Vladimir A.
AU  - Ćirković, Jovana
AU  - Holló, Berta Barta
AU  - Đokić, Veljko R.
AU  - Donnard, Morgan
AU  - Gulea, Mihaela
AU  - Marjanović, Ivana
AU  - Klisurić, Olivera R.
AU  - Todorović, Tamara R.
PY  - 2021
UR  - https://dais.sanu.ac.rs/123456789/11757
AB  - Four silver-based coordination polymers, {[Ag(L1)2]NO3}∞ (1), {[Ag(L1)2]ClO4}∞ (2), {[Ag(L2)2]NO3·H2O}∞ (3) and {[Ag(L2)2]ClO4}∞ (4), were synthesized using the thiomorpholine-4-carbonitrile (L1) and piperazine-1,4-dicarbonitrile (L2) ligands. Compounds 1 and 2 are two-dimensional, while 3 and 4 are three-dimensional. L1 and L2 are 1,4-bis-monodentate ligands in all compounds, while Ag(I) ions are four-coordinated in a slightly distorted tetrahedral geometry. Topological analysis in standard representations suggests that underlying nets in 1 and 2 have an sql topology, while 3 and 4 exhibit a dia topology. Thermal analysis shows that 3 loses crystalline water at room temperature, while other compounds show good thermal stability. All compounds show good photocatalytic activity for photocatalytic degradation of the mordant blue 9 dye, with reaction rates in the range 0.029 to 0.061 min−1. The best result was obtained for compound 4, which can be correlated to its largest lattice volume.
PB  - Royal Society of Chemistry (RSC)
T2  - CrystEngComm
T1  - 2D and 3D silver-based coordination polymers with thiomorpholine-4-carbonitrile and piperazine-1,4-dicarbonitrile: structure, intermolecular interactions, photocatalysis, and thermal behavior
SP  - 4799
EP  - 4815
VL  - 23
IS  - 27
DO  - 10.1039/D1CE00394A
UR  - https://hdl.handle.net/21.15107/rcub_dais_11757
ER  - 
@article{
author = "Ristić, Predrag and Filipović, Nenad and Blagojević, Vladimir A. and Ćirković, Jovana and Holló, Berta Barta and Đokić, Veljko R. and Donnard, Morgan and Gulea, Mihaela and Marjanović, Ivana and Klisurić, Olivera R. and Todorović, Tamara R.",
year = "2021",
abstract = "Four silver-based coordination polymers, {[Ag(L1)2]NO3}∞ (1), {[Ag(L1)2]ClO4}∞ (2), {[Ag(L2)2]NO3·H2O}∞ (3) and {[Ag(L2)2]ClO4}∞ (4), were synthesized using the thiomorpholine-4-carbonitrile (L1) and piperazine-1,4-dicarbonitrile (L2) ligands. Compounds 1 and 2 are two-dimensional, while 3 and 4 are three-dimensional. L1 and L2 are 1,4-bis-monodentate ligands in all compounds, while Ag(I) ions are four-coordinated in a slightly distorted tetrahedral geometry. Topological analysis in standard representations suggests that underlying nets in 1 and 2 have an sql topology, while 3 and 4 exhibit a dia topology. Thermal analysis shows that 3 loses crystalline water at room temperature, while other compounds show good thermal stability. All compounds show good photocatalytic activity for photocatalytic degradation of the mordant blue 9 dye, with reaction rates in the range 0.029 to 0.061 min−1. The best result was obtained for compound 4, which can be correlated to its largest lattice volume.",
publisher = "Royal Society of Chemistry (RSC)",
journal = "CrystEngComm",
title = "2D and 3D silver-based coordination polymers with thiomorpholine-4-carbonitrile and piperazine-1,4-dicarbonitrile: structure, intermolecular interactions, photocatalysis, and thermal behavior",
pages = "4799-4815",
volume = "23",
number = "27",
doi = "10.1039/D1CE00394A",
url = "https://hdl.handle.net/21.15107/rcub_dais_11757"
}
Ristić, P., Filipović, N., Blagojević, V. A., Ćirković, J., Holló, B. B., Đokić, V. R., Donnard, M., Gulea, M., Marjanović, I., Klisurić, O. R.,& Todorović, T. R.. (2021). 2D and 3D silver-based coordination polymers with thiomorpholine-4-carbonitrile and piperazine-1,4-dicarbonitrile: structure, intermolecular interactions, photocatalysis, and thermal behavior. in CrystEngComm
Royal Society of Chemistry (RSC)., 23(27), 4799-4815.
https://doi.org/10.1039/D1CE00394A
https://hdl.handle.net/21.15107/rcub_dais_11757
Ristić P, Filipović N, Blagojević VA, Ćirković J, Holló BB, Đokić VR, Donnard M, Gulea M, Marjanović I, Klisurić OR, Todorović TR. 2D and 3D silver-based coordination polymers with thiomorpholine-4-carbonitrile and piperazine-1,4-dicarbonitrile: structure, intermolecular interactions, photocatalysis, and thermal behavior. in CrystEngComm. 2021;23(27):4799-4815.
doi:10.1039/D1CE00394A
https://hdl.handle.net/21.15107/rcub_dais_11757 .
Ristić, Predrag, Filipović, Nenad, Blagojević, Vladimir A., Ćirković, Jovana, Holló, Berta Barta, Đokić, Veljko R., Donnard, Morgan, Gulea, Mihaela, Marjanović, Ivana, Klisurić, Olivera R., Todorović, Tamara R., "2D and 3D silver-based coordination polymers with thiomorpholine-4-carbonitrile and piperazine-1,4-dicarbonitrile: structure, intermolecular interactions, photocatalysis, and thermal behavior" in CrystEngComm, 23, no. 27 (2021):4799-4815,
https://doi.org/10.1039/D1CE00394A .,
https://hdl.handle.net/21.15107/rcub_dais_11757 .
3
4
3

Freeze vs. Spray Drying for Dry Wild Thyme (Thymus serpyllum L.) Extract Formulations: The Impact of Gelatin as a Coating Material

Jovanović, Aleksandra A.; Lević, Steva M.; Pavlović, Vladimir B.; Marković, Smilja B.; Pjanović, Rada V.; Đorđević, Verica B.; Nedović, Viktor; Bugarski, Branko M.

(Basel : MDPI AG, 2021)

TY  - JOUR
AU  - Jovanović, Aleksandra A.
AU  - Lević, Steva M.
AU  - Pavlović, Vladimir B.
AU  - Marković, Smilja B.
AU  - Pjanović, Rada V.
AU  - Đorđević, Verica B.
AU  - Nedović, Viktor
AU  - Bugarski, Branko M.
PY  - 2021
UR  - https://dais.sanu.ac.rs/123456789/11798
AB  - Freeze drying was compared with spray drying regarding feasibility to process wild thyme drugs in order to obtain dry formulations at laboratory scale starting from liquid extracts produced by different extraction methods: maceration and heat-, ultrasound-, and microwave-assisted extractions. Higher total powder yield (based on the dry weight prior to extraction) was achieved by freeze than spray drying and lower loss of total polyphenol content (TPC) and total flavonoid content (TFC) due to the drying process. Gelatin as a coating agent (5% w/w) provided better TPC recovery by 70% in case of lyophilization and higher total powder yield in case of spray drying by diminishing material deposition on the wall of the drying chamber. The resulting gelatin-free and gelatin-containing powders carried polyphenols in amount ~190 and 53–75 mg gallic acid equivalents GAE/g of powder, respectively. Microwave-assisted extract formulation was distinguished from the others by a higher content of polyphenols, proteins and sugars, higher bulk density and lower solubility. The type of the drying process mainly affected the position of the gelatin-derived -OH and amide bands in FTIR spectra. Spray-dried formulations compared to freeze-dried expressed higher thermal stability as confirmed by differential scanning calorimetry analysis and a higher diffusion coefficient; the last feature can be associated with the lower specific surface area of irregularly shaped freeze-dried particles (151–223 µm) compared to small microspheres (~8 µm) in spray-dried powder.
PB  - Basel : MDPI AG
T2  - Molecules
T1  - Freeze vs. Spray Drying for Dry Wild Thyme (Thymus serpyllum L.) Extract Formulations: The Impact of Gelatin as a Coating Material
SP  - 3933
VL  - 26
IS  - 13
DO  - 10.3390/molecules26133933
UR  - https://hdl.handle.net/21.15107/rcub_dais_11798
ER  - 
@article{
author = "Jovanović, Aleksandra A. and Lević, Steva M. and Pavlović, Vladimir B. and Marković, Smilja B. and Pjanović, Rada V. and Đorđević, Verica B. and Nedović, Viktor and Bugarski, Branko M.",
year = "2021",
abstract = "Freeze drying was compared with spray drying regarding feasibility to process wild thyme drugs in order to obtain dry formulations at laboratory scale starting from liquid extracts produced by different extraction methods: maceration and heat-, ultrasound-, and microwave-assisted extractions. Higher total powder yield (based on the dry weight prior to extraction) was achieved by freeze than spray drying and lower loss of total polyphenol content (TPC) and total flavonoid content (TFC) due to the drying process. Gelatin as a coating agent (5% w/w) provided better TPC recovery by 70% in case of lyophilization and higher total powder yield in case of spray drying by diminishing material deposition on the wall of the drying chamber. The resulting gelatin-free and gelatin-containing powders carried polyphenols in amount ~190 and 53–75 mg gallic acid equivalents GAE/g of powder, respectively. Microwave-assisted extract formulation was distinguished from the others by a higher content of polyphenols, proteins and sugars, higher bulk density and lower solubility. The type of the drying process mainly affected the position of the gelatin-derived -OH and amide bands in FTIR spectra. Spray-dried formulations compared to freeze-dried expressed higher thermal stability as confirmed by differential scanning calorimetry analysis and a higher diffusion coefficient; the last feature can be associated with the lower specific surface area of irregularly shaped freeze-dried particles (151–223 µm) compared to small microspheres (~8 µm) in spray-dried powder.",
publisher = "Basel : MDPI AG",
journal = "Molecules",
title = "Freeze vs. Spray Drying for Dry Wild Thyme (Thymus serpyllum L.) Extract Formulations: The Impact of Gelatin as a Coating Material",
pages = "3933",
volume = "26",
number = "13",
doi = "10.3390/molecules26133933",
url = "https://hdl.handle.net/21.15107/rcub_dais_11798"
}
Jovanović, A. A., Lević, S. M., Pavlović, V. B., Marković, S. B., Pjanović, R. V., Đorđević, V. B., Nedović, V.,& Bugarski, B. M.. (2021). Freeze vs. Spray Drying for Dry Wild Thyme (Thymus serpyllum L.) Extract Formulations: The Impact of Gelatin as a Coating Material. in Molecules
Basel : MDPI AG., 26(13), 3933.
https://doi.org/10.3390/molecules26133933
https://hdl.handle.net/21.15107/rcub_dais_11798
Jovanović AA, Lević SM, Pavlović VB, Marković SB, Pjanović RV, Đorđević VB, Nedović V, Bugarski BM. Freeze vs. Spray Drying for Dry Wild Thyme (Thymus serpyllum L.) Extract Formulations: The Impact of Gelatin as a Coating Material. in Molecules. 2021;26(13):3933.
doi:10.3390/molecules26133933
https://hdl.handle.net/21.15107/rcub_dais_11798 .
Jovanović, Aleksandra A., Lević, Steva M., Pavlović, Vladimir B., Marković, Smilja B., Pjanović, Rada V., Đorđević, Verica B., Nedović, Viktor, Bugarski, Branko M., "Freeze vs. Spray Drying for Dry Wild Thyme (Thymus serpyllum L.) Extract Formulations: The Impact of Gelatin as a Coating Material" in Molecules, 26, no. 13 (2021):3933,
https://doi.org/10.3390/molecules26133933 .,
https://hdl.handle.net/21.15107/rcub_dais_11798 .
14
4
10

Evaluation of adsorption performance and quantum chemical modeling of pesticides removal using Cell-MG hybrid adsorbent

Perendija, Jovana; Veličković, Zlate; Dražević, Ljubinka; Stojiljković, Ivana N.; Milčić, Miloš K.; Milosavljević, Milutin M.; Marinković, Aleksandar; Pavlović, Vladimir B.

(Association for ETRAN Society, 2021)

TY  - JOUR
AU  - Perendija, Jovana
AU  - Veličković, Zlate
AU  - Dražević, Ljubinka
AU  - Stojiljković, Ivana N.
AU  - Milčić, Miloš K.
AU  - Milosavljević, Milutin M.
AU  - Marinković, Aleksandar
AU  - Pavlović, Vladimir B.
PY  - 2021
UR  - https://dais.sanu.ac.rs/123456789/11948
AB  - Magnetite (MG) modified cellulose membrane (Cell-MG), obtained by reaction of 3-aminosilane and subsequently with diethylenetriaminepentaacetic acid dianhydride functionalized waste Cell fibers (Cell-NH2 and Cell-DTPA, respectively), and amino-modified diatomite was used for Azoxystrobin and Iprodione removal from water. Cell-MG membrane was structurally and morphologically characterized using FT-IR and FE-SEM techniques. The influences of operational parameters, i.e. pH, contact time, temperature, and the mass of adsorbent on adsorption and kinetics were studied in a batch system. The calculated capacities of 35.32 and 30.16 mg g-1 for Azoxystrobin and Iprodione, respectively, were obtained from non-linear Langmuir model fitting. Weber-Morris model fitting indicates the main contribution of intra-particle diffusion to overall mass transport resistance. Thermodynamic data indicate spontaneous and endothermic adsorption. The reusability of adsorbent and results from wastewater purification showed that Cell-MG could be used as general-purpose adsorbent. The adsorbent/adsorbate surface interaction was considered from the results obtained using density functional theory (DFT) and calculation of molecular electrostatic potential (MEP). Thus, a better understanding of the relation between the adsorption performances and contribution of non-specific and specific interactions to adsorption performances and design of novel adsorbent with improved properties was deduced
PB  - Association for ETRAN Society
T2  - Science of Sintering
T1  - Evaluation of adsorption performance and quantum chemical modeling of pesticides removal using Cell-MG hybrid adsorbent
SP  - 355
EP  - 378
VL  - 53
IS  - 3
DO  - 10.2298/SOS2103355P
UR  - https://hdl.handle.net/21.15107/rcub_dais_11948
ER  - 
@article{
author = "Perendija, Jovana and Veličković, Zlate and Dražević, Ljubinka and Stojiljković, Ivana N. and Milčić, Miloš K. and Milosavljević, Milutin M. and Marinković, Aleksandar and Pavlović, Vladimir B.",
year = "2021",
abstract = "Magnetite (MG) modified cellulose membrane (Cell-MG), obtained by reaction of 3-aminosilane and subsequently with diethylenetriaminepentaacetic acid dianhydride functionalized waste Cell fibers (Cell-NH2 and Cell-DTPA, respectively), and amino-modified diatomite was used for Azoxystrobin and Iprodione removal from water. Cell-MG membrane was structurally and morphologically characterized using FT-IR and FE-SEM techniques. The influences of operational parameters, i.e. pH, contact time, temperature, and the mass of adsorbent on adsorption and kinetics were studied in a batch system. The calculated capacities of 35.32 and 30.16 mg g-1 for Azoxystrobin and Iprodione, respectively, were obtained from non-linear Langmuir model fitting. Weber-Morris model fitting indicates the main contribution of intra-particle diffusion to overall mass transport resistance. Thermodynamic data indicate spontaneous and endothermic adsorption. The reusability of adsorbent and results from wastewater purification showed that Cell-MG could be used as general-purpose adsorbent. The adsorbent/adsorbate surface interaction was considered from the results obtained using density functional theory (DFT) and calculation of molecular electrostatic potential (MEP). Thus, a better understanding of the relation between the adsorption performances and contribution of non-specific and specific interactions to adsorption performances and design of novel adsorbent with improved properties was deduced",
publisher = "Association for ETRAN Society",
journal = "Science of Sintering",
title = "Evaluation of adsorption performance and quantum chemical modeling of pesticides removal using Cell-MG hybrid adsorbent",
pages = "355-378",
volume = "53",
number = "3",
doi = "10.2298/SOS2103355P",
url = "https://hdl.handle.net/21.15107/rcub_dais_11948"
}
Perendija, J., Veličković, Z., Dražević, L., Stojiljković, I. N., Milčić, M. K., Milosavljević, M. M., Marinković, A.,& Pavlović, V. B.. (2021). Evaluation of adsorption performance and quantum chemical modeling of pesticides removal using Cell-MG hybrid adsorbent. in Science of Sintering
Association for ETRAN Society., 53(3), 355-378.
https://doi.org/10.2298/SOS2103355P
https://hdl.handle.net/21.15107/rcub_dais_11948
Perendija J, Veličković Z, Dražević L, Stojiljković IN, Milčić MK, Milosavljević MM, Marinković A, Pavlović VB. Evaluation of adsorption performance and quantum chemical modeling of pesticides removal using Cell-MG hybrid adsorbent. in Science of Sintering. 2021;53(3):355-378.
doi:10.2298/SOS2103355P
https://hdl.handle.net/21.15107/rcub_dais_11948 .
Perendija, Jovana, Veličković, Zlate, Dražević, Ljubinka, Stojiljković, Ivana N., Milčić, Miloš K., Milosavljević, Milutin M., Marinković, Aleksandar, Pavlović, Vladimir B., "Evaluation of adsorption performance and quantum chemical modeling of pesticides removal using Cell-MG hybrid adsorbent" in Science of Sintering, 53, no. 3 (2021):355-378,
https://doi.org/10.2298/SOS2103355P .,
https://hdl.handle.net/21.15107/rcub_dais_11948 .
2
2

Immobilized Alcalase on Micron- and Submicron-Sized Alginate Beads as a Potential Biocatalyst for Hydrolysis of Food Proteins

Jonović, Marko; Žuža, Milena; Đorđević, Verica; Šekuljica, Nataša; Milivojević, Milan; Jugović, Branimir; Bugarski, Branko; Knežević Jugović, Zorica

(Basel : Multidisciplinary Digital Publishing Institute (MDPI), 2021)

TY  - JOUR
AU  - Jonović, Marko
AU  - Žuža, Milena
AU  - Đorđević, Verica
AU  - Šekuljica, Nataša
AU  - Milivojević, Milan
AU  - Jugović, Branimir
AU  - Bugarski, Branko
AU  - Knežević Jugović, Zorica
PY  - 2021
UR  - https://dais.sanu.ac.rs/123456789/12087
AB  - Enzymatic hydrolysis of food proteins is convenient method to improve their functional properties and physiological activity. Herein, the successful covalent attachment of alcalase on alginate micron and submicron beads using the carbodiimide based chemistry reaction and the subsequent application of the beads for egg white and soy proteins hydrolysis were studied. In addition to the electrostatic extrusion technique (EE) previously used by others, the potential utilization of a novel ultrasonic spray atomization technique without drying (UA) and with drying (UAD) for alginate submicron beads production has been attempted. The immobilization parameters were optimized on microbeads obtained by EE technique (803 +/- 23 mu m) with respect to enzyme loading and alcalase activity. UA and UAD techniques resulted in much smaller particles (607 +/- 103 nm and 394 +/- 51 nm in diameter, respectively), enabling even higher enzyme loading of 671.6 +/- 4 mg g(-1) on the carrier and the highest immobilized alcalase activity of 2716.1 IU g(-1) in the standard reaction. The UAD biocatalyst exhibited also better performances in the real food system based on egg white or soy proteins. It has been shown that the immobilized alcalase can be reused in seven successive soy protein hydrolysis cycles with a little decrease in the activity.
PB  - Basel : Multidisciplinary Digital Publishing Institute (MDPI)
T2  - catalysts
T1  - Immobilized Alcalase on Micron- and Submicron-Sized Alginate Beads as a Potential Biocatalyst for Hydrolysis of Food Proteins
SP  - 305
VL  - 11
IS  - 3
DO  - 10.3390/catal11030305
UR  - https://hdl.handle.net/21.15107/rcub_dais_12087
ER  - 
@article{
author = "Jonović, Marko and Žuža, Milena and Đorđević, Verica and Šekuljica, Nataša and Milivojević, Milan and Jugović, Branimir and Bugarski, Branko and Knežević Jugović, Zorica",
year = "2021",
abstract = "Enzymatic hydrolysis of food proteins is convenient method to improve their functional properties and physiological activity. Herein, the successful covalent attachment of alcalase on alginate micron and submicron beads using the carbodiimide based chemistry reaction and the subsequent application of the beads for egg white and soy proteins hydrolysis were studied. In addition to the electrostatic extrusion technique (EE) previously used by others, the potential utilization of a novel ultrasonic spray atomization technique without drying (UA) and with drying (UAD) for alginate submicron beads production has been attempted. The immobilization parameters were optimized on microbeads obtained by EE technique (803 +/- 23 mu m) with respect to enzyme loading and alcalase activity. UA and UAD techniques resulted in much smaller particles (607 +/- 103 nm and 394 +/- 51 nm in diameter, respectively), enabling even higher enzyme loading of 671.6 +/- 4 mg g(-1) on the carrier and the highest immobilized alcalase activity of 2716.1 IU g(-1) in the standard reaction. The UAD biocatalyst exhibited also better performances in the real food system based on egg white or soy proteins. It has been shown that the immobilized alcalase can be reused in seven successive soy protein hydrolysis cycles with a little decrease in the activity.",
publisher = "Basel : Multidisciplinary Digital Publishing Institute (MDPI)",
journal = "catalysts",
title = "Immobilized Alcalase on Micron- and Submicron-Sized Alginate Beads as a Potential Biocatalyst for Hydrolysis of Food Proteins",
pages = "305",
volume = "11",
number = "3",
doi = "10.3390/catal11030305",
url = "https://hdl.handle.net/21.15107/rcub_dais_12087"
}
Jonović, M., Žuža, M., Đorđević, V., Šekuljica, N., Milivojević, M., Jugović, B., Bugarski, B.,& Knežević Jugović, Z.. (2021). Immobilized Alcalase on Micron- and Submicron-Sized Alginate Beads as a Potential Biocatalyst for Hydrolysis of Food Proteins. in catalysts
Basel : Multidisciplinary Digital Publishing Institute (MDPI)., 11(3), 305.
https://doi.org/10.3390/catal11030305
https://hdl.handle.net/21.15107/rcub_dais_12087
Jonović M, Žuža M, Đorđević V, Šekuljica N, Milivojević M, Jugović B, Bugarski B, Knežević Jugović Z. Immobilized Alcalase on Micron- and Submicron-Sized Alginate Beads as a Potential Biocatalyst for Hydrolysis of Food Proteins. in catalysts. 2021;11(3):305.
doi:10.3390/catal11030305
https://hdl.handle.net/21.15107/rcub_dais_12087 .
Jonović, Marko, Žuža, Milena, Đorđević, Verica, Šekuljica, Nataša, Milivojević, Milan, Jugović, Branimir, Bugarski, Branko, Knežević Jugović, Zorica, "Immobilized Alcalase on Micron- and Submicron-Sized Alginate Beads as a Potential Biocatalyst for Hydrolysis of Food Proteins" in catalysts, 11, no. 3 (2021):305,
https://doi.org/10.3390/catal11030305 .,
https://hdl.handle.net/21.15107/rcub_dais_12087 .
3
4

The influence of self-doping on electrochemical synthesis and behaviour of polyaniline

Gvozdenović, Milica M.; Jugović, Branimir; Jokić, Bojan; Džunuzović, Enis S.; Grgur, Branimir

(Beograd : Udruženje inženjera Srbije za koroziju i zaštitu materijala UISKOZAM, 2021)

TY  - CONF
AU  - Gvozdenović, Milica M.
AU  - Jugović, Branimir
AU  - Jokić, Bojan
AU  - Džunuzović, Enis S.
AU  - Grgur, Branimir
PY  - 2021
UR  - https://dais.sanu.ac.rs/123456789/12383
AB  - Electrochemical synthesis was used to polymerize aniline and copolymerize aniline and m-aminobenzoic from aqueous acidic electrolyte containing aniline and aniline with different amount of m-aminobenzoic acid. These materials were obtained galvanostatically at graphite electrode at current density of 1.0 mA cm-2 from aqueous electrolyte containing 1.0 mol dm-3 HCl and different amount of monomers. The effect of self-doping due to meta positioned carboxylic group was observed in both synthesis parameters, morphology, degree of oxidation and electrochemical behaviour. The presence of m-aminobenzoic acid led higher copolymerization increasing with the increase of amount of m-aminobenzoic acid if comparing to polymerization potential of aniline. Moreover, the copolymer with equal amount of aniline/m-aminobenzoic acid showed electrochemical activity in neutral electrolyte which might be due to possibility of proton exchange process which can be expelled from the copolymer during oxidation process together by insertion of anions, making this material promising for use in electrochemical biosensors.
AB  - Elektrohemijski postupak korišćen je za polimerizaciju anilina i kopolimerizaciju anilina i m-aminobenzoeve kiseline iz kiselog vodenog rastvora elektrolita sa različitim molskim odnosima anilina i m-aminobezoeve kiseline. Ovi materijali dobijeni su uslovima konstantne gustine struje od 1,0 mA cm-2 iz kiselog vodenog elektrolita koji je sadržavao 1,0 mol dm-3 HCl, anilin i m-aminobenzoevu kiselinu. Uticaj samo-dopovanja koji je posledica prisustva karboskilne grupe u meta položaju ispoljavao se u različitim parametrima sinteze, morfologiji dobijenih materijala, stepenu oksidacije i elektrohemijskom ponašanju. Prisustvo m-aminobenzoeve kiseline uslovilo je veći potencijal sinteze kopolimera u odnosu na polianilin koji je rastao sa porastom udela m-aminobezoeve kiseline. Kopolimer koji je dobijen iz elektrolita sa jednakim molskim odnosom anilina i m-aminobenzoeve kiseline pokazao je elektrohemijsku aktivnost u neutralnom elektrolitu koja može biti posledica razmene protona što ovaj materijal čini perspektivnim za praktičnu primenu u elektrohemijskim biosenzorima.
PB  - Beograd : Udruženje inženjera Srbije za koroziju i zaštitu materijala UISKOZAM
C3  - Meeting point of the science and practice in the fields of corrosion, materials and environmental protection : proceedings = Stecište nauke i prakse u oblastima korozije, zaštite materijala i životne sredine : knjiga radova / XXII YuCorr International Conference = XXI YuCorr [Jugoslovenska korozija] Međunarodna konferencija, September 13-16, 2021, Tara Mountain, Serbia, 2021
T1  - The influence of self-doping on electrochemical synthesis and behaviour of polyaniline
T1  - Uticaj samodopovanja na elektrohemijsku sintezu i svojstva polianilina
SP  - POSTER-139
UR  - https://hdl.handle.net/21.15107/rcub_dais_12383
ER  - 
@conference{
author = "Gvozdenović, Milica M. and Jugović, Branimir and Jokić, Bojan and Džunuzović, Enis S. and Grgur, Branimir",
year = "2021",
abstract = "Electrochemical synthesis was used to polymerize aniline and copolymerize aniline and m-aminobenzoic from aqueous acidic electrolyte containing aniline and aniline with different amount of m-aminobenzoic acid. These materials were obtained galvanostatically at graphite electrode at current density of 1.0 mA cm-2 from aqueous electrolyte containing 1.0 mol dm-3 HCl and different amount of monomers. The effect of self-doping due to meta positioned carboxylic group was observed in both synthesis parameters, morphology, degree of oxidation and electrochemical behaviour. The presence of m-aminobenzoic acid led higher copolymerization increasing with the increase of amount of m-aminobenzoic acid if comparing to polymerization potential of aniline. Moreover, the copolymer with equal amount of aniline/m-aminobenzoic acid showed electrochemical activity in neutral electrolyte which might be due to possibility of proton exchange process which can be expelled from the copolymer during oxidation process together by insertion of anions, making this material promising for use in electrochemical biosensors., Elektrohemijski postupak korišćen je za polimerizaciju anilina i kopolimerizaciju anilina i m-aminobenzoeve kiseline iz kiselog vodenog rastvora elektrolita sa različitim molskim odnosima anilina i m-aminobezoeve kiseline. Ovi materijali dobijeni su uslovima konstantne gustine struje od 1,0 mA cm-2 iz kiselog vodenog elektrolita koji je sadržavao 1,0 mol dm-3 HCl, anilin i m-aminobenzoevu kiselinu. Uticaj samo-dopovanja koji je posledica prisustva karboskilne grupe u meta položaju ispoljavao se u različitim parametrima sinteze, morfologiji dobijenih materijala, stepenu oksidacije i elektrohemijskom ponašanju. Prisustvo m-aminobenzoeve kiseline uslovilo je veći potencijal sinteze kopolimera u odnosu na polianilin koji je rastao sa porastom udela m-aminobezoeve kiseline. Kopolimer koji je dobijen iz elektrolita sa jednakim molskim odnosom anilina i m-aminobenzoeve kiseline pokazao je elektrohemijsku aktivnost u neutralnom elektrolitu koja može biti posledica razmene protona što ovaj materijal čini perspektivnim za praktičnu primenu u elektrohemijskim biosenzorima.",
publisher = "Beograd : Udruženje inženjera Srbije za koroziju i zaštitu materijala UISKOZAM",
journal = "Meeting point of the science and practice in the fields of corrosion, materials and environmental protection : proceedings = Stecište nauke i prakse u oblastima korozije, zaštite materijala i životne sredine : knjiga radova / XXII YuCorr International Conference = XXI YuCorr [Jugoslovenska korozija] Međunarodna konferencija, September 13-16, 2021, Tara Mountain, Serbia, 2021",
title = "The influence of self-doping on electrochemical synthesis and behaviour of polyaniline, Uticaj samodopovanja na elektrohemijsku sintezu i svojstva polianilina",
pages = "POSTER-139",
url = "https://hdl.handle.net/21.15107/rcub_dais_12383"
}
Gvozdenović, M. M., Jugović, B., Jokić, B., Džunuzović, E. S.,& Grgur, B.. (2021). The influence of self-doping on electrochemical synthesis and behaviour of polyaniline. in Meeting point of the science and practice in the fields of corrosion, materials and environmental protection : proceedings = Stecište nauke i prakse u oblastima korozije, zaštite materijala i životne sredine : knjiga radova / XXII YuCorr International Conference = XXI YuCorr [Jugoslovenska korozija] Međunarodna konferencija, September 13-16, 2021, Tara Mountain, Serbia, 2021
Beograd : Udruženje inženjera Srbije za koroziju i zaštitu materijala UISKOZAM., POSTER-139.
https://hdl.handle.net/21.15107/rcub_dais_12383
Gvozdenović MM, Jugović B, Jokić B, Džunuzović ES, Grgur B. The influence of self-doping on electrochemical synthesis and behaviour of polyaniline. in Meeting point of the science and practice in the fields of corrosion, materials and environmental protection : proceedings = Stecište nauke i prakse u oblastima korozije, zaštite materijala i životne sredine : knjiga radova / XXII YuCorr International Conference = XXI YuCorr [Jugoslovenska korozija] Međunarodna konferencija, September 13-16, 2021, Tara Mountain, Serbia, 2021. 2021;:POSTER-139.
https://hdl.handle.net/21.15107/rcub_dais_12383 .
Gvozdenović, Milica M., Jugović, Branimir, Jokić, Bojan, Džunuzović, Enis S., Grgur, Branimir, "The influence of self-doping on electrochemical synthesis and behaviour of polyaniline" in Meeting point of the science and practice in the fields of corrosion, materials and environmental protection : proceedings = Stecište nauke i prakse u oblastima korozije, zaštite materijala i životne sredine : knjiga radova / XXII YuCorr International Conference = XXI YuCorr [Jugoslovenska korozija] Međunarodna konferencija, September 13-16, 2021, Tara Mountain, Serbia, 2021 (2021):POSTER-139,
https://hdl.handle.net/21.15107/rcub_dais_12383 .

Aqueous electrolyte polypyrrole | zinc cell with supercapattery performance

Janačković, Marija; Gvozdenović, Milica M.; Jugović, Branimir; Grgur, Branimir

(Beograd : Udruženje inženjera Srbije za koroziju i zaštitu materijala UISKOZAM, 2021)

TY  - CONF
AU  - Janačković, Marija
AU  - Gvozdenović, Milica M.
AU  - Jugović, Branimir
AU  - Grgur, Branimir
PY  - 2021
UR  - https://dais.sanu.ac.rs/123456789/12382
AB  - Electrochemical oxidative polymerization at constant current density was used to produce polypyrrole (PPY) at graphite electrode from aqueous acidic electrolyte containing 0,1 mol dm-3 pyrrole and 1,0 mol dm-3 HCl. PPY electrode was than used as cathode while zinc electrode served as anode in electrochemical cell with an aqueous electrolyte containing 2,0 mol dm-3 NH4Cl and 1,1 mol dm-3 ZnCl2. The relevant electrochemical parameters of this cell were evaluated from electrochemical experiments. It was observed that charge of Zn|PPY cell started at voltage between 0,5 and 0,7 V and proceeded up to 1,5 V. Charge/discharge of the cell was dependent on charge/discharge current density with open circuit voltage of the fully discharged cell around 1,3 V. The estimated values of specific energy were between 46 and 68 W h kg-1 while specific power values were between 125 and 380 W kg-1, which suggested that Zn|PPY cell had “supercapaterry” behavior.
AB  - Elektroda na bazi polipirola (PPY) dobijena je elektrohemijskom oksidativnom polimerizacijom na grafitnoj elektrodi u uslovima konstantne gustine struje. Kao elektrolit za sintezu, korišćen je vodeni rastvor 0,1 mol dm-3 pirola i 1,0 mol dm-3 HCl. Formirana je elektrohemijska ćelija u kojoj je elektroda na bazi PPY korišćena kao katoda dok je anoda bila elektroda od cinka, a elektrolit se sastojao od vodenog rastvora 2,0 mol dm-3 NH4Cl i 1,1 mol dm-3 ZnCl2. Procena relevantnih elektrohemijskih i električnih parametara ove ćelije bazirana je na elektrohemijskim eksperimentima. Utvrđeno je da je proces punjenja/pražnjenja zavisio od struje punjenja/pražnjenja, punejnje ćelije započinje na naponu između 0,5 i 0,7 V, a završava se na naponu od oko 1,3 V. Procenjene vrednosti energije bile su između 46 i 68 W h kg-1, dok se za specifičnu snagu dobijaju vrednosti između 125 i 380 W kg-1, što ukazuje na superkapabaterijska svojstva Zn|PPY ćelije.
PB  - Beograd : Udruženje inženjera Srbije za koroziju i zaštitu materijala UISKOZAM
C3  - Meeting point of the science and practice in the fields of corrosion, materials and environmental protection : proceedings = Stecište nauke i prakse u oblastima korozije, zaštite materijala i životne sredine : knjiga radova / XXII YuCorr International Conference = XXI YuCorr [Jugoslovenska korozija] Međunarodna konferencija, September 13-16, 2021, Tara Mountain, Serbia
T1  - Aqueous electrolyte polypyrrole | zinc cell with supercapattery performance
T1  - Polipirol | cink ćelija sa vodenim rastvorom elektrolita i svojstvima superkapabaterije
SP  - ORAL-75
UR  - https://hdl.handle.net/21.15107/rcub_dais_12382
ER  - 
@conference{
author = "Janačković, Marija and Gvozdenović, Milica M. and Jugović, Branimir and Grgur, Branimir",
year = "2021",
abstract = "Electrochemical oxidative polymerization at constant current density was used to produce polypyrrole (PPY) at graphite electrode from aqueous acidic electrolyte containing 0,1 mol dm-3 pyrrole and 1,0 mol dm-3 HCl. PPY electrode was than used as cathode while zinc electrode served as anode in electrochemical cell with an aqueous electrolyte containing 2,0 mol dm-3 NH4Cl and 1,1 mol dm-3 ZnCl2. The relevant electrochemical parameters of this cell were evaluated from electrochemical experiments. It was observed that charge of Zn|PPY cell started at voltage between 0,5 and 0,7 V and proceeded up to 1,5 V. Charge/discharge of the cell was dependent on charge/discharge current density with open circuit voltage of the fully discharged cell around 1,3 V. The estimated values of specific energy were between 46 and 68 W h kg-1 while specific power values were between 125 and 380 W kg-1, which suggested that Zn|PPY cell had “supercapaterry” behavior., Elektroda na bazi polipirola (PPY) dobijena je elektrohemijskom oksidativnom polimerizacijom na grafitnoj elektrodi u uslovima konstantne gustine struje. Kao elektrolit za sintezu, korišćen je vodeni rastvor 0,1 mol dm-3 pirola i 1,0 mol dm-3 HCl. Formirana je elektrohemijska ćelija u kojoj je elektroda na bazi PPY korišćena kao katoda dok je anoda bila elektroda od cinka, a elektrolit se sastojao od vodenog rastvora 2,0 mol dm-3 NH4Cl i 1,1 mol dm-3 ZnCl2. Procena relevantnih elektrohemijskih i električnih parametara ove ćelije bazirana je na elektrohemijskim eksperimentima. Utvrđeno je da je proces punjenja/pražnjenja zavisio od struje punjenja/pražnjenja, punejnje ćelije započinje na naponu između 0,5 i 0,7 V, a završava se na naponu od oko 1,3 V. Procenjene vrednosti energije bile su između 46 i 68 W h kg-1, dok se za specifičnu snagu dobijaju vrednosti između 125 i 380 W kg-1, što ukazuje na superkapabaterijska svojstva Zn|PPY ćelije.",
publisher = "Beograd : Udruženje inženjera Srbije za koroziju i zaštitu materijala UISKOZAM",
journal = "Meeting point of the science and practice in the fields of corrosion, materials and environmental protection : proceedings = Stecište nauke i prakse u oblastima korozije, zaštite materijala i životne sredine : knjiga radova / XXII YuCorr International Conference = XXI YuCorr [Jugoslovenska korozija] Međunarodna konferencija, September 13-16, 2021, Tara Mountain, Serbia",
title = "Aqueous electrolyte polypyrrole | zinc cell with supercapattery performance, Polipirol | cink ćelija sa vodenim rastvorom elektrolita i svojstvima superkapabaterije",
pages = "ORAL-75",
url = "https://hdl.handle.net/21.15107/rcub_dais_12382"
}
Janačković, M., Gvozdenović, M. M., Jugović, B.,& Grgur, B.. (2021). Aqueous electrolyte polypyrrole | zinc cell with supercapattery performance. in Meeting point of the science and practice in the fields of corrosion, materials and environmental protection : proceedings = Stecište nauke i prakse u oblastima korozije, zaštite materijala i životne sredine : knjiga radova / XXII YuCorr International Conference = XXI YuCorr [Jugoslovenska korozija] Međunarodna konferencija, September 13-16, 2021, Tara Mountain, Serbia
Beograd : Udruženje inženjera Srbije za koroziju i zaštitu materijala UISKOZAM., ORAL-75.
https://hdl.handle.net/21.15107/rcub_dais_12382
Janačković M, Gvozdenović MM, Jugović B, Grgur B. Aqueous electrolyte polypyrrole | zinc cell with supercapattery performance. in Meeting point of the science and practice in the fields of corrosion, materials and environmental protection : proceedings = Stecište nauke i prakse u oblastima korozije, zaštite materijala i životne sredine : knjiga radova / XXII YuCorr International Conference = XXI YuCorr [Jugoslovenska korozija] Međunarodna konferencija, September 13-16, 2021, Tara Mountain, Serbia. 2021;:ORAL-75.
https://hdl.handle.net/21.15107/rcub_dais_12382 .
Janačković, Marija, Gvozdenović, Milica M., Jugović, Branimir, Grgur, Branimir, "Aqueous electrolyte polypyrrole | zinc cell with supercapattery performance" in Meeting point of the science and practice in the fields of corrosion, materials and environmental protection : proceedings = Stecište nauke i prakse u oblastima korozije, zaštite materijala i životne sredine : knjiga radova / XXII YuCorr International Conference = XXI YuCorr [Jugoslovenska korozija] Međunarodna konferencija, September 13-16, 2021, Tara Mountain, Serbia (2021):ORAL-75,
https://hdl.handle.net/21.15107/rcub_dais_12382 .

Synthesis and deposition of MAPbBr3 perovskite on titania nanotube arrays

Stefanović, Milica; Vujančević, Jelena; Petrović, Rada; Janaćković, Đorđe

(Belgrade : Materials Research Society of Serbia, 2021)

TY  - CONF
AU  - Stefanović, Milica
AU  - Vujančević, Jelena
AU  - Petrović, Rada
AU  - Janaćković, Đorđe
PY  - 2021
UR  - https://dais.sanu.ac.rs/123456789/12075
AB  - The organo-inorganic perovskites are materials that have recently revolutionized the field of
photovoltaics due to their low-cost fabrication and high optical absorption. The hybrid organoinorganic perovskite absorbs the visible part of the spectrum resulting in the creation of electron-hole pair. To decrease the recombination of charge carriers, the construction of solar cells requires the existence of separate layers for holes and for electrons. TiO2 is usually used as an electron transport layer because its conduction band (CB) lies under the CB of perovskite. In that way, electrons diffuse from CB of perovskite to CB of TiO2. For these experiments, TiO2 nanotubular structure was used as an electron transport layer due to its advantages compared to nanoparticular TiO2. TiO2 nanotubes can provide a one-dimensional transmission channel for the charge carriers, so it will reduce the recombination rate of the carriers and provide a channel for fast carrier transport. However, there is a problem with the contact surface between perovskite and TiO2 nanotubes. The aim of this study is to increase the contact surface of perovskite and TiO2 nanotubes by filling the nanotubes with perovskite material in order to improve electron transport. Methylammonium lead bromide perovskite (MAPbBr3) was deposited on anodically synthesized TiO2 nanotubes which were annealed at 450 °C for 1 h. After degassation of the sample under high vacuum for 3 h at 200 °C, the cooled sample was put in a solution of MAPbBr3 in dimethylformamide (DMF) and it was treated with inert gas (N2), which enabled the filling of the nanotubes with perovskite material to some extent. FESEM and XRD analyses were used for morphological and chemical characterization of the sample. The diffuse reflectance spectroscopy measurement of the sample proved that deposition of MAPbBr3 improves the absorption properties of TiO2 nanotubes. By measuring the I-V characteristics of the sample in the dark and under visible light, a hysteresis curve was obtained.
PB  - Belgrade : Materials Research Society of Serbia
C3  - Programme and the Book of abstracts / Twenty-second Annual Conference YUCOMAT 2021 Herceg Novi, Montenegro, August 30 - September 3, 2021
T1  - Synthesis and deposition of MAPbBr3 perovskite on titania nanotube arrays
SP  - 111
EP  - 111
UR  - https://hdl.handle.net/21.15107/rcub_dais_12075
ER  - 
@conference{
author = "Stefanović, Milica and Vujančević, Jelena and Petrović, Rada and Janaćković, Đorđe",
year = "2021",
abstract = "The organo-inorganic perovskites are materials that have recently revolutionized the field of
photovoltaics due to their low-cost fabrication and high optical absorption. The hybrid organoinorganic perovskite absorbs the visible part of the spectrum resulting in the creation of electron-hole pair. To decrease the recombination of charge carriers, the construction of solar cells requires the existence of separate layers for holes and for electrons. TiO2 is usually used as an electron transport layer because its conduction band (CB) lies under the CB of perovskite. In that way, electrons diffuse from CB of perovskite to CB of TiO2. For these experiments, TiO2 nanotubular structure was used as an electron transport layer due to its advantages compared to nanoparticular TiO2. TiO2 nanotubes can provide a one-dimensional transmission channel for the charge carriers, so it will reduce the recombination rate of the carriers and provide a channel for fast carrier transport. However, there is a problem with the contact surface between perovskite and TiO2 nanotubes. The aim of this study is to increase the contact surface of perovskite and TiO2 nanotubes by filling the nanotubes with perovskite material in order to improve electron transport. Methylammonium lead bromide perovskite (MAPbBr3) was deposited on anodically synthesized TiO2 nanotubes which were annealed at 450 °C for 1 h. After degassation of the sample under high vacuum for 3 h at 200 °C, the cooled sample was put in a solution of MAPbBr3 in dimethylformamide (DMF) and it was treated with inert gas (N2), which enabled the filling of the nanotubes with perovskite material to some extent. FESEM and XRD analyses were used for morphological and chemical characterization of the sample. The diffuse reflectance spectroscopy measurement of the sample proved that deposition of MAPbBr3 improves the absorption properties of TiO2 nanotubes. By measuring the I-V characteristics of the sample in the dark and under visible light, a hysteresis curve was obtained.",
publisher = "Belgrade : Materials Research Society of Serbia",
journal = "Programme and the Book of abstracts / Twenty-second Annual Conference YUCOMAT 2021 Herceg Novi, Montenegro, August 30 - September 3, 2021",
title = "Synthesis and deposition of MAPbBr3 perovskite on titania nanotube arrays",
pages = "111-111",
url = "https://hdl.handle.net/21.15107/rcub_dais_12075"
}
Stefanović, M., Vujančević, J., Petrović, R.,& Janaćković, Đ.. (2021). Synthesis and deposition of MAPbBr3 perovskite on titania nanotube arrays. in Programme and the Book of abstracts / Twenty-second Annual Conference YUCOMAT 2021 Herceg Novi, Montenegro, August 30 - September 3, 2021
Belgrade : Materials Research Society of Serbia., 111-111.
https://hdl.handle.net/21.15107/rcub_dais_12075
Stefanović M, Vujančević J, Petrović R, Janaćković Đ. Synthesis and deposition of MAPbBr3 perovskite on titania nanotube arrays. in Programme and the Book of abstracts / Twenty-second Annual Conference YUCOMAT 2021 Herceg Novi, Montenegro, August 30 - September 3, 2021. 2021;:111-111.
https://hdl.handle.net/21.15107/rcub_dais_12075 .
Stefanović, Milica, Vujančević, Jelena, Petrović, Rada, Janaćković, Đorđe, "Synthesis and deposition of MAPbBr3 perovskite on titania nanotube arrays" in Programme and the Book of abstracts / Twenty-second Annual Conference YUCOMAT 2021 Herceg Novi, Montenegro, August 30 - September 3, 2021 (2021):111-111,
https://hdl.handle.net/21.15107/rcub_dais_12075 .