TY  - JOUR
AU  - Obradović, Nina
AU  - Pavlović, Vera P.
AU  - Kachlik, Martin
AU  - Maca, Karel
AU  - Olćan, Dragan
AU  - Đorđević, Antonije
AU  - Tshantshapanyan, Ani
AU  - Vlahović, Branislav
AU  - Pavlović, Vladimir B.
PY  - 2019
UR  - https://dais.sanu.ac.rs/123456789/4557
AB  - Sintering of pure cordierite 2MgO:2Al2O3:5SiO2, and cordierite with the addition of 5 mass % TeO2 was studied. Green bodies were prepared from powder mixtures mechanically activated in a high-energy planetary mill, shaped by uniaxial (20 MPa) and cold isostatic pressing (1000 MPa). The pressure-less sintering of these specimens was performed at 1350°C for 1 h. High relative density over 95% of the theoretical value was obtained through solid-state reaction and pressure-less sintering of powder activated for 40 min, and for the first time reported in the literature. Phase composition and microstructures of sintered samples were determined by XRD and SEM, coupled with EDS mapping. The real part of the complex relative permittivity of the samples was measured at 200 MHz. The loss tangent of all samples was below the resolution of the measurement setup. A strong correlation between the relative permittivity and the density agrees with previously published data.
PB  - Taylor and Francis
T2  - Advances in Applied Ceramics
T1  - Processing and properties of dense cordierite ceramics obtained through solid-state reaction and pressure-less sintering
SP  - 241
EP  - 248
VL  - 118
IS  - 5
DO  - 10.1080/17436753.2018.1548150
UR  - https://hdl.handle.net/21.15107/rcub_dais_4557
ER  - 

@article{
author = "Obradović, Nina and Pavlović, Vera P. and Kachlik, Martin and Maca, Karel and Olćan, Dragan and Đorđević, Antonije and Tshantshapanyan, Ani and Vlahović, Branislav and Pavlović, Vladimir B.",
year = "2019",
abstract = "Sintering of pure cordierite 2MgO:2Al2O3:5SiO2, and cordierite with the addition of 5 mass % TeO2 was studied. Green bodies were prepared from powder mixtures mechanically activated in a high-energy planetary mill, shaped by uniaxial (20 MPa) and cold isostatic pressing (1000 MPa). The pressure-less sintering of these specimens was performed at 1350°C for 1 h. High relative density over 95% of the theoretical value was obtained through solid-state reaction and pressure-less sintering of powder activated for 40 min, and for the first time reported in the literature. Phase composition and microstructures of sintered samples were determined by XRD and SEM, coupled with EDS mapping. The real part of the complex relative permittivity of the samples was measured at 200 MHz. The loss tangent of all samples was below the resolution of the measurement setup. A strong correlation between the relative permittivity and the density agrees with previously published data.",
publisher = "Taylor and Francis",
journal = "Advances in Applied Ceramics",
title = "Processing and properties of dense cordierite ceramics obtained through solid-state reaction and pressure-less sintering",
pages = "241-248",
volume = "118",
number = "5",
doi = "10.1080/17436753.2018.1548150",
url = "https://hdl.handle.net/21.15107/rcub_dais_4557"
}

Obradović, N., Pavlović, V. P., Kachlik, M., Maca, K., Olćan, D., Đorđević, A., Tshantshapanyan, A., Vlahović, B.,& Pavlović, V. B.. (2019). Processing and properties of dense cordierite ceramics obtained through solid-state reaction and pressure-less sintering. in Advances in Applied Ceramics
Taylor and Francis., 118(5), 241-248.
https://doi.org/10.1080/17436753.2018.1548150
https://hdl.handle.net/21.15107/rcub_dais_4557

Obradović N, Pavlović VP, Kachlik M, Maca K, Olćan D, Đorđević A, Tshantshapanyan A, Vlahović B, Pavlović VB. Processing and properties of dense cordierite ceramics obtained through solid-state reaction and pressure-less sintering. in Advances in Applied Ceramics. 2019;118(5):241-248.
doi:10.1080/17436753.2018.1548150
https://hdl.handle.net/21.15107/rcub_dais_4557 .

Obradović, Nina, Pavlović, Vera P., Kachlik, Martin, Maca, Karel, Olćan, Dragan, Đorđević, Antonije, Tshantshapanyan, Ani, Vlahović, Branislav, Pavlović, Vladimir B., "Processing and properties of dense cordierite ceramics obtained through solid-state reaction and pressure-less sintering" in Advances in Applied Ceramics, 118, no. 5 (2019):241-248,
https://doi.org/10.1080/17436753.2018.1548150 .,
https://hdl.handle.net/21.15107/rcub_dais_4557 .

TY  - JOUR
AU  - Obradović, Nina
AU  - Blagojević, Vladimir A.
AU  - Filipović, Suzana
AU  - Đorđević, Nataša
AU  - Kosanović, Darko
AU  - Marković, Smilja
AU  - Kachlik, Martin
AU  - Maca, Karel
AU  - Pavlović, Vladimir B.
PY  - 2019
UR  - https://dais.sanu.ac.rs/123456789/4558
AB  - Thermally activated processes in cordierite-based ceramics were investigated to determine the effect of the mechanical activation and the addition of TeO2 on kinetic and thermodynamic parameters of these processes. Using a combination of dilatometry and DTA measurements in the 100–1400 °C temperature range, it was established that both the mechanical activation and the addition of TeO2 have a significant effect on processes in cordierite-based ceramics. A combination of 5 mass% addition of TeO2 and mechanical activation for 40 min reduced the sintering temperature of cordierite ceramics to around 1100 °C. In addition, the analysis of DTA measurements of mechanically activated samples indicates that the mechanical activation leads to intensification of the cordierite formation through an increase in concentration of surface defects and an increase in grain contact surface in the initial powder.
PB  - Springer
T2  - Journal of Thermal Analysis and Calorimetry
T1  - Kinetics of thermally activated processes in cordierite-based ceramics
SP  - 2989
EP  - 2998
VL  - 138
DO  - 10.1007/s10973-018-7924-1
UR  - https://hdl.handle.net/21.15107/rcub_dais_4558
ER  - 

@article{
author = "Obradović, Nina and Blagojević, Vladimir A. and Filipović, Suzana and Đorđević, Nataša and Kosanović, Darko and Marković, Smilja and Kachlik, Martin and Maca, Karel and Pavlović, Vladimir B.",
year = "2019",
abstract = "Thermally activated processes in cordierite-based ceramics were investigated to determine the effect of the mechanical activation and the addition of TeO2 on kinetic and thermodynamic parameters of these processes. Using a combination of dilatometry and DTA measurements in the 100–1400 °C temperature range, it was established that both the mechanical activation and the addition of TeO2 have a significant effect on processes in cordierite-based ceramics. A combination of 5 mass% addition of TeO2 and mechanical activation for 40 min reduced the sintering temperature of cordierite ceramics to around 1100 °C. In addition, the analysis of DTA measurements of mechanically activated samples indicates that the mechanical activation leads to intensification of the cordierite formation through an increase in concentration of surface defects and an increase in grain contact surface in the initial powder.",
publisher = "Springer",
journal = "Journal of Thermal Analysis and Calorimetry",
title = "Kinetics of thermally activated processes in cordierite-based ceramics",
pages = "2989-2998",
volume = "138",
doi = "10.1007/s10973-018-7924-1",
url = "https://hdl.handle.net/21.15107/rcub_dais_4558"
}

Obradović, N., Blagojević, V. A., Filipović, S., Đorđević, N., Kosanović, D., Marković, S., Kachlik, M., Maca, K.,& Pavlović, V. B.. (2019). Kinetics of thermally activated processes in cordierite-based ceramics. in Journal of Thermal Analysis and Calorimetry
Springer., 138, 2989-2998.
https://doi.org/10.1007/s10973-018-7924-1
https://hdl.handle.net/21.15107/rcub_dais_4558

Obradović N, Blagojević VA, Filipović S, Đorđević N, Kosanović D, Marković S, Kachlik M, Maca K, Pavlović VB. Kinetics of thermally activated processes in cordierite-based ceramics. in Journal of Thermal Analysis and Calorimetry. 2019;138:2989-2998.
doi:10.1007/s10973-018-7924-1
https://hdl.handle.net/21.15107/rcub_dais_4558 .

Obradović, Nina, Blagojević, Vladimir A., Filipović, Suzana, Đorđević, Nataša, Kosanović, Darko, Marković, Smilja, Kachlik, Martin, Maca, Karel, Pavlović, Vladimir B., "Kinetics of thermally activated processes in cordierite-based ceramics" in Journal of Thermal Analysis and Calorimetry, 138 (2019):2989-2998,
https://doi.org/10.1007/s10973-018-7924-1 .,
https://hdl.handle.net/21.15107/rcub_dais_4558 .

TY  - JOUR
AU  - Obradović, Nina
AU  - Blagojević, Vladimir A.
AU  - Filipović, Suzana
AU  - Đorđević, Nataša
AU  - Kosanović, Darko
AU  - Marković, Smilja
AU  - Kachlik, Martin
AU  - Maca, Karel
AU  - Pavlović, Vladimir B.
PY  - 2019
UR  - https://dais.sanu.ac.rs/123456789/7048
AB  - Thermally activated processes in cordierite-based ceramics were investigated to determine the effect of the mechanical activation and the addition of TeO2 on kinetic and thermodynamic parameters of these processes. Using a combination of dilatometry and DTA measurements in the 100–1400 °C temperature range, it was established that both the mechanical activation and the addition of TeO2 have a significant effect on processes in cordierite-based ceramics. A combination of 5 mass% addition of TeO2 and mechanical activation for 40 min reduced the sintering temperature of cordierite ceramics to around 1100 °C. In addition, the analysis of DTA measurements of mechanically activated samples indicates that the mechanical activation leads to intensification of the cordierite formation through an increase in concentration of surface defects and an increase in grain contact surface in the initial powder.
PB  - Springer
T2  - Journal of Thermal Analysis and Calorimetry
T1  - Kinetics of thermally activated processes in cordierite-based ceramics
SP  - 2989
EP  - 2998
VL  - 138
DO  - 10.1007/s10973-018-7924-1
UR  - https://hdl.handle.net/21.15107/rcub_dais_7048
ER  - 

@article{
author = "Obradović, Nina and Blagojević, Vladimir A. and Filipović, Suzana and Đorđević, Nataša and Kosanović, Darko and Marković, Smilja and Kachlik, Martin and Maca, Karel and Pavlović, Vladimir B.",
year = "2019",
abstract = "Thermally activated processes in cordierite-based ceramics were investigated to determine the effect of the mechanical activation and the addition of TeO2 on kinetic and thermodynamic parameters of these processes. Using a combination of dilatometry and DTA measurements in the 100–1400 °C temperature range, it was established that both the mechanical activation and the addition of TeO2 have a significant effect on processes in cordierite-based ceramics. A combination of 5 mass% addition of TeO2 and mechanical activation for 40 min reduced the sintering temperature of cordierite ceramics to around 1100 °C. In addition, the analysis of DTA measurements of mechanically activated samples indicates that the mechanical activation leads to intensification of the cordierite formation through an increase in concentration of surface defects and an increase in grain contact surface in the initial powder.",
publisher = "Springer",
journal = "Journal of Thermal Analysis and Calorimetry",
title = "Kinetics of thermally activated processes in cordierite-based ceramics",
pages = "2989-2998",
volume = "138",
doi = "10.1007/s10973-018-7924-1",
url = "https://hdl.handle.net/21.15107/rcub_dais_7048"
}

Obradović, N., Blagojević, V. A., Filipović, S., Đorđević, N., Kosanović, D., Marković, S., Kachlik, M., Maca, K.,& Pavlović, V. B.. (2019). Kinetics of thermally activated processes in cordierite-based ceramics. in Journal of Thermal Analysis and Calorimetry
Springer., 138, 2989-2998.
https://doi.org/10.1007/s10973-018-7924-1
https://hdl.handle.net/21.15107/rcub_dais_7048

Obradović N, Blagojević VA, Filipović S, Đorđević N, Kosanović D, Marković S, Kachlik M, Maca K, Pavlović VB. Kinetics of thermally activated processes in cordierite-based ceramics. in Journal of Thermal Analysis and Calorimetry. 2019;138:2989-2998.
doi:10.1007/s10973-018-7924-1
https://hdl.handle.net/21.15107/rcub_dais_7048 .

Obradović, Nina, Blagojević, Vladimir A., Filipović, Suzana, Đorđević, Nataša, Kosanović, Darko, Marković, Smilja, Kachlik, Martin, Maca, Karel, Pavlović, Vladimir B., "Kinetics of thermally activated processes in cordierite-based ceramics" in Journal of Thermal Analysis and Calorimetry, 138 (2019):2989-2998,
https://doi.org/10.1007/s10973-018-7924-1 .,
https://hdl.handle.net/21.15107/rcub_dais_7048 .