Tshantshapanyan, Ani

Link to this page

Authority KeyName Variants
8ef1ae46-232d-445b-a4f1-b72d4e056449
  • Tshantshapanyan, Ani (2)
Projects

Author's Bibliography

Processing and properties of dense cordierite ceramics obtained through solid-state reaction and pressure-less sintering

Obradović, Nina; Pavlović, Vera P.; Kachlik, Martin; Maca, Karel; Olćan, Dragan; Đorđević, Antonije; Tshantshapanyan, Ani; Vlahović, Branislav; Pavlović, Vladimir B.

(Taylor and Francis, 2019)

TY  - JOUR
AU  - Obradović, Nina
AU  - Pavlović, Vera P.
AU  - Kachlik, Martin
AU  - Maca, Karel
AU  - Olćan, Dragan
AU  - Đorđević, Antonije
AU  - Tshantshapanyan, Ani
AU  - Vlahović, Branislav
AU  - Pavlović, Vladimir B.
PY  - 2019
UR  - https://dais.sanu.ac.rs/123456789/4557
AB  - Sintering of pure cordierite 2MgO:2Al2O3:5SiO2, and cordierite with the addition of 5 mass % TeO2 was studied. Green bodies were prepared from powder mixtures mechanically activated in a high-energy planetary mill, shaped by uniaxial (20 MPa) and cold isostatic pressing (1000 MPa). The pressure-less sintering of these specimens was performed at 1350°C for 1 h. High relative density over 95% of the theoretical value was obtained through solid-state reaction and pressure-less sintering of powder activated for 40 min, and for the first time reported in the literature. Phase composition and microstructures of sintered samples were determined by XRD and SEM, coupled with EDS mapping. The real part of the complex relative permittivity of the samples was measured at 200 MHz. The loss tangent of all samples was below the resolution of the measurement setup. A strong correlation between the relative permittivity and the density agrees with previously published data.
PB  - Taylor and Francis
T2  - Advances in Applied Ceramics
T1  - Processing and properties of dense cordierite ceramics obtained through solid-state reaction and pressure-less sintering
SP  - 241
EP  - 248
VL  - 118
IS  - 5
DO  - 10.1080/17436753.2018.1548150
UR  - https://hdl.handle.net/21.15107/rcub_dais_4557
ER  - 
@article{
author = "Obradović, Nina and Pavlović, Vera P. and Kachlik, Martin and Maca, Karel and Olćan, Dragan and Đorđević, Antonije and Tshantshapanyan, Ani and Vlahović, Branislav and Pavlović, Vladimir B.",
year = "2019",
abstract = "Sintering of pure cordierite 2MgO:2Al2O3:5SiO2, and cordierite with the addition of 5 mass % TeO2 was studied. Green bodies were prepared from powder mixtures mechanically activated in a high-energy planetary mill, shaped by uniaxial (20 MPa) and cold isostatic pressing (1000 MPa). The pressure-less sintering of these specimens was performed at 1350°C for 1 h. High relative density over 95% of the theoretical value was obtained through solid-state reaction and pressure-less sintering of powder activated for 40 min, and for the first time reported in the literature. Phase composition and microstructures of sintered samples were determined by XRD and SEM, coupled with EDS mapping. The real part of the complex relative permittivity of the samples was measured at 200 MHz. The loss tangent of all samples was below the resolution of the measurement setup. A strong correlation between the relative permittivity and the density agrees with previously published data.",
publisher = "Taylor and Francis",
journal = "Advances in Applied Ceramics",
title = "Processing and properties of dense cordierite ceramics obtained through solid-state reaction and pressure-less sintering",
pages = "241-248",
volume = "118",
number = "5",
doi = "10.1080/17436753.2018.1548150",
url = "https://hdl.handle.net/21.15107/rcub_dais_4557"
}
Obradović, N., Pavlović, V. P., Kachlik, M., Maca, K., Olćan, D., Đorđević, A., Tshantshapanyan, A., Vlahović, B.,& Pavlović, V. B.. (2019). Processing and properties of dense cordierite ceramics obtained through solid-state reaction and pressure-less sintering. in Advances in Applied Ceramics
Taylor and Francis., 118(5), 241-248.
https://doi.org/10.1080/17436753.2018.1548150
https://hdl.handle.net/21.15107/rcub_dais_4557
Obradović N, Pavlović VP, Kachlik M, Maca K, Olćan D, Đorđević A, Tshantshapanyan A, Vlahović B, Pavlović VB. Processing and properties of dense cordierite ceramics obtained through solid-state reaction and pressure-less sintering. in Advances in Applied Ceramics. 2019;118(5):241-248.
doi:10.1080/17436753.2018.1548150
https://hdl.handle.net/21.15107/rcub_dais_4557 .
Obradović, Nina, Pavlović, Vera P., Kachlik, Martin, Maca, Karel, Olćan, Dragan, Đorđević, Antonije, Tshantshapanyan, Ani, Vlahović, Branislav, Pavlović, Vladimir B., "Processing and properties of dense cordierite ceramics obtained through solid-state reaction and pressure-less sintering" in Advances in Applied Ceramics, 118, no. 5 (2019):241-248,
https://doi.org/10.1080/17436753.2018.1548150 .,
https://hdl.handle.net/21.15107/rcub_dais_4557 .
3
4
5

Shungite – a carbon-mineral rock material: Its sinterability and possible applications

Obradović, Nina; Gigov, Mihajlo; Đorđević, Aleksandar; Kern, Frank; Dmitrović, S.; Matović, Branko; Ðorđević, Antonije; Tshantshapanyan, Ani; Vlahović, Branislav; Petrović, Predrag; Pavlović, Vladimir B.

(Novi Sad : Faculty of Technology, University of Novi Sad, 2019)

TY  - JOUR
AU  - Obradović, Nina
AU  - Gigov, Mihajlo
AU  - Đorđević, Aleksandar
AU  - Kern, Frank
AU  - Dmitrović, S.
AU  - Matović, Branko
AU  - Ðorđević, Antonije
AU  - Tshantshapanyan, Ani
AU  - Vlahović, Branislav
AU  - Petrović, Predrag
AU  - Pavlović, Vladimir B.
PY  - 2019
UR  - https://dais.sanu.ac.rs/123456789/6372
AB  - The paper presents results of the influence of mechanical activation of shungite, a carbon-mineral rock material rich in silica and carbon, on its sintering behaviour, and obtaining of pure SiC ceramics. The mechanical activation of the starting powder was performed in a high-energy ball mill in time intervals from 30 to 480 min. The phase composition of the starting powders and sintered samples was analysed by the X-ray diffraction method. The first traces of SiC were detected after sintering at 1350 °C for 2 h in an Ar atmosphere, along with traces of unreacted SiO2. The scanning electron microscopy was performed in order to determine changes in the microstructure. Sintering was performed at various temperatures for 2 h, in an Ar atmosphere and a vacuum. Dielectric properties of the sintered samples were measured in the frequency range from 1 to 500 MHz. The obtained results indicate that the sintered powder is a good candidate for applications as an absorber of electromagnetic waves in microwave engineering. © 2019 University of Novi Sad, Faculty of Technology. All rights reserved.
PB  - Novi Sad : Faculty of Technology, University of Novi Sad
T2  - Processing and Application of Ceramics
T1  - Shungite – a carbon-mineral rock material: Its sinterability and possible applications
SP  - 89
EP  - 97
VL  - 13
IS  - 1
DO  - 10.2298/PAC1901089O
UR  - https://hdl.handle.net/21.15107/rcub_dais_6372
ER  - 
@article{
author = "Obradović, Nina and Gigov, Mihajlo and Đorđević, Aleksandar and Kern, Frank and Dmitrović, S. and Matović, Branko and Ðorđević, Antonije and Tshantshapanyan, Ani and Vlahović, Branislav and Petrović, Predrag and Pavlović, Vladimir B.",
year = "2019",
abstract = "The paper presents results of the influence of mechanical activation of shungite, a carbon-mineral rock material rich in silica and carbon, on its sintering behaviour, and obtaining of pure SiC ceramics. The mechanical activation of the starting powder was performed in a high-energy ball mill in time intervals from 30 to 480 min. The phase composition of the starting powders and sintered samples was analysed by the X-ray diffraction method. The first traces of SiC were detected after sintering at 1350 °C for 2 h in an Ar atmosphere, along with traces of unreacted SiO2. The scanning electron microscopy was performed in order to determine changes in the microstructure. Sintering was performed at various temperatures for 2 h, in an Ar atmosphere and a vacuum. Dielectric properties of the sintered samples were measured in the frequency range from 1 to 500 MHz. The obtained results indicate that the sintered powder is a good candidate for applications as an absorber of electromagnetic waves in microwave engineering. © 2019 University of Novi Sad, Faculty of Technology. All rights reserved.",
publisher = "Novi Sad : Faculty of Technology, University of Novi Sad",
journal = "Processing and Application of Ceramics",
title = "Shungite – a carbon-mineral rock material: Its sinterability and possible applications",
pages = "89-97",
volume = "13",
number = "1",
doi = "10.2298/PAC1901089O",
url = "https://hdl.handle.net/21.15107/rcub_dais_6372"
}
Obradović, N., Gigov, M., Đorđević, A., Kern, F., Dmitrović, S., Matović, B., Ðorđević, A., Tshantshapanyan, A., Vlahović, B., Petrović, P.,& Pavlović, V. B.. (2019). Shungite – a carbon-mineral rock material: Its sinterability and possible applications. in Processing and Application of Ceramics
Novi Sad : Faculty of Technology, University of Novi Sad., 13(1), 89-97.
https://doi.org/10.2298/PAC1901089O
https://hdl.handle.net/21.15107/rcub_dais_6372
Obradović N, Gigov M, Đorđević A, Kern F, Dmitrović S, Matović B, Ðorđević A, Tshantshapanyan A, Vlahović B, Petrović P, Pavlović VB. Shungite – a carbon-mineral rock material: Its sinterability and possible applications. in Processing and Application of Ceramics. 2019;13(1):89-97.
doi:10.2298/PAC1901089O
https://hdl.handle.net/21.15107/rcub_dais_6372 .
Obradović, Nina, Gigov, Mihajlo, Đorđević, Aleksandar, Kern, Frank, Dmitrović, S., Matović, Branko, Ðorđević, Antonije, Tshantshapanyan, Ani, Vlahović, Branislav, Petrović, Predrag, Pavlović, Vladimir B., "Shungite – a carbon-mineral rock material: Its sinterability and possible applications" in Processing and Application of Ceramics, 13, no. 1 (2019):89-97,
https://doi.org/10.2298/PAC1901089O .,
https://hdl.handle.net/21.15107/rcub_dais_6372 .
5
5
5