TY  - CONF
AU  - Đorđević, Miloš
AU  - Paunović, Vesna
AU  - Mitić, Vojislav V.
PY  - 2019
UR  - https://dais.sanu.ac.rs/123456789/6682
AB  - In this paper, electrical characteristics of Ho2O3 doped BaTiO3 ceramics were shown, using new method for measuring samples. The BaTiO3 doped samples were sintered at 1320°C for 4 hours. The concentration of the additives were from 0.05 to 1.0 at% Ho. The density was ranged from 83% to 91% of theoretical density (TD). The samples of BaTiO3 ceramics doped with Ho2O3 are characterized by spherical and irregular polygonal grains. The average grain size for samples doped with low content of Ho2O3 (0.05 at% Ho) ranged from 10 μm to 30 μm. An increase in dopant concentration causes a decrease in the average grain size in the investigated samples. So it is for samples doped with 1.0 at% Ho, grain size range between less than 1 mm – 2 mm. The variation of dielectric permittivity with temperature were measured in the temperature range from 30°C to 180°C and the frequency range from 100 Hz to 1 MHz. For measurement electrical characteristic a new method was used, which implemented to automate the sampling and to enable measurement without a human factor. The software application is connected via USB communication to a microcontroller, which measures the temperature in the furnace. When the temperature reaches the defined value, the microcontroller sends information to the software application. Then the application through GPIB communication activates the LCR meter, which measures the defined parameters of the tested samples. Based on parameters such as dielectric constant (εr), tangent losses (tan δ) and impedance, the characteristics of the tested samples were determined. Using the Curie-Weiss law and modified Curie-Weiss law, based on the measured values of the parameters, the Curie constant and the exponent of nonlinearity were determined.
PB  - Belgrade : Serbian Ceramic Society
C3  - Program and the Book of abstracts / Serbian Ceramic Society Conference Advanced Ceramics and Application VIII : New Frontiers in Multifunctional Material Science and Processing, Serbia, Belgrade, 23-25. September 2019
T1  - Electrical Characteristics of Ho doped BaTiO3 Ceramics
SP  - 55
EP  - 55
UR  - https://hdl.handle.net/21.15107/rcub_dais_6682
ER  - 

@conference{
author = "Đorđević, Miloš and Paunović, Vesna and Mitić, Vojislav V.",
year = "2019",
abstract = "In this paper, electrical characteristics of Ho2O3 doped BaTiO3 ceramics were shown, using new method for measuring samples. The BaTiO3 doped samples were sintered at 1320°C for 4 hours. The concentration of the additives were from 0.05 to 1.0 at% Ho. The density was ranged from 83% to 91% of theoretical density (TD). The samples of BaTiO3 ceramics doped with Ho2O3 are characterized by spherical and irregular polygonal grains. The average grain size for samples doped with low content of Ho2O3 (0.05 at% Ho) ranged from 10 μm to 30 μm. An increase in dopant concentration causes a decrease in the average grain size in the investigated samples. So it is for samples doped with 1.0 at% Ho, grain size range between less than 1 mm – 2 mm. The variation of dielectric permittivity with temperature were measured in the temperature range from 30°C to 180°C and the frequency range from 100 Hz to 1 MHz. For measurement electrical characteristic a new method was used, which implemented to automate the sampling and to enable measurement without a human factor. The software application is connected via USB communication to a microcontroller, which measures the temperature in the furnace. When the temperature reaches the defined value, the microcontroller sends information to the software application. Then the application through GPIB communication activates the LCR meter, which measures the defined parameters of the tested samples. Based on parameters such as dielectric constant (εr), tangent losses (tan δ) and impedance, the characteristics of the tested samples were determined. Using the Curie-Weiss law and modified Curie-Weiss law, based on the measured values of the parameters, the Curie constant and the exponent of nonlinearity were determined.",
publisher = "Belgrade : Serbian Ceramic Society",
journal = "Program and the Book of abstracts / Serbian Ceramic Society Conference Advanced Ceramics and Application VIII : New Frontiers in Multifunctional Material Science and Processing, Serbia, Belgrade, 23-25. September 2019",
title = "Electrical Characteristics of Ho doped BaTiO3 Ceramics",
pages = "55-55",
url = "https://hdl.handle.net/21.15107/rcub_dais_6682"
}

Đorđević, M., Paunović, V.,& Mitić, V. V.. (2019). Electrical Characteristics of Ho doped BaTiO3 Ceramics. in Program and the Book of abstracts / Serbian Ceramic Society Conference Advanced Ceramics and Application VIII : New Frontiers in Multifunctional Material Science and Processing, Serbia, Belgrade, 23-25. September 2019
Belgrade : Serbian Ceramic Society., 55-55.
https://hdl.handle.net/21.15107/rcub_dais_6682

Đorđević M, Paunović V, Mitić VV. Electrical Characteristics of Ho doped BaTiO3 Ceramics. in Program and the Book of abstracts / Serbian Ceramic Society Conference Advanced Ceramics and Application VIII : New Frontiers in Multifunctional Material Science and Processing, Serbia, Belgrade, 23-25. September 2019. 2019;:55-55.
https://hdl.handle.net/21.15107/rcub_dais_6682 .

Đorđević, Miloš, Paunović, Vesna, Mitić, Vojislav V., "Electrical Characteristics of Ho doped BaTiO3 Ceramics" in Program and the Book of abstracts / Serbian Ceramic Society Conference Advanced Ceramics and Application VIII : New Frontiers in Multifunctional Material Science and Processing, Serbia, Belgrade, 23-25. September 2019 (2019):55-55,
https://hdl.handle.net/21.15107/rcub_dais_6682 .

TY  - CONF
AU  - Đorđević, Miloš
AU  - Paunović, Vesna
AU  - Mitić, Vojislav V.
AU  - Prijić, Zoran
AU  - Marjanović, Miloš
PY  - 2017
UR  - https://dais.sanu.ac.rs/123456789/2391
AB  - The electrical resistivity and PTCR (Positive Temperature Coefficient of Resistivity) effect doped BaTiO3 ceramics with different dopant were investigated in this paper, The content of additive in doped samples were ranged from 0.01 to 1.0 at% Er/Yb. The samples were prepared by a conventional solid state sintering procedure and sintered at 1320 °C for 4 hours. For samples doped with Er2O3 (0.01 at% Er/Yb), SEM analysis shows abnormal grain growth with the average size range between 20 μm - 40 μm. For samples doped with Yb2O3 the average size was from 30 μm - 50 μm. With increase of dopants concentration the average grain size decreases, and for samples doped with 1.0 at% Er/Yb, grain size range between 3 μm - 20 μm for samples doped with Er and between 1 μm - 10 μm for samples doped with Yb2O3. The specific electrical resistance were measured in temperature range from 25 °C to 170°C at different frequencies, ranged from 100Hz to 1MHz. To a temperature of 120 °C, resistance has a slight increase with increasing of temperature, but above this temperature the resistance rapidly increasing. The value of the specific electrical resistance decreases with increasing concentration of Er/Yb, reached the minimum at certain dopant content (0.5 at% Er/Yb), then increased rapidly with dopant content in high doping level.
PB  - Belgrade : Serbian Ceramic Society
C3  - Program and the Book of Abstracts / Serbian Ceramic Society Conference Advanced Ceramics and Application VI: New Frontiers in Multifunctional Material Science and Processing, Serbia, Belgrade, September 18-20, 2017
T1  - Electrical properties of doped BaTiO3 Ceramics
SP  - 66
EP  - 66
UR  - https://hdl.handle.net/21.15107/rcub_dais_2391
ER  - 

@conference{
author = "Đorđević, Miloš and Paunović, Vesna and Mitić, Vojislav V. and Prijić, Zoran and Marjanović, Miloš",
year = "2017",
abstract = "The electrical resistivity and PTCR (Positive Temperature Coefficient of Resistivity) effect doped BaTiO3 ceramics with different dopant were investigated in this paper, The content of additive in doped samples were ranged from 0.01 to 1.0 at% Er/Yb. The samples were prepared by a conventional solid state sintering procedure and sintered at 1320 °C for 4 hours. For samples doped with Er2O3 (0.01 at% Er/Yb), SEM analysis shows abnormal grain growth with the average size range between 20 μm - 40 μm. For samples doped with Yb2O3 the average size was from 30 μm - 50 μm. With increase of dopants concentration the average grain size decreases, and for samples doped with 1.0 at% Er/Yb, grain size range between 3 μm - 20 μm for samples doped with Er and between 1 μm - 10 μm for samples doped with Yb2O3. The specific electrical resistance were measured in temperature range from 25 °C to 170°C at different frequencies, ranged from 100Hz to 1MHz. To a temperature of 120 °C, resistance has a slight increase with increasing of temperature, but above this temperature the resistance rapidly increasing. The value of the specific electrical resistance decreases with increasing concentration of Er/Yb, reached the minimum at certain dopant content (0.5 at% Er/Yb), then increased rapidly with dopant content in high doping level.",
publisher = "Belgrade : Serbian Ceramic Society",
journal = "Program and the Book of Abstracts / Serbian Ceramic Society Conference Advanced Ceramics and Application VI: New Frontiers in Multifunctional Material Science and Processing, Serbia, Belgrade, September 18-20, 2017",
title = "Electrical properties of doped BaTiO3 Ceramics",
pages = "66-66",
url = "https://hdl.handle.net/21.15107/rcub_dais_2391"
}

Đorđević, M., Paunović, V., Mitić, V. V., Prijić, Z.,& Marjanović, M.. (2017). Electrical properties of doped BaTiO3 Ceramics. in Program and the Book of Abstracts / Serbian Ceramic Society Conference Advanced Ceramics and Application VI: New Frontiers in Multifunctional Material Science and Processing, Serbia, Belgrade, September 18-20, 2017
Belgrade : Serbian Ceramic Society., 66-66.
https://hdl.handle.net/21.15107/rcub_dais_2391

Đorđević M, Paunović V, Mitić VV, Prijić Z, Marjanović M. Electrical properties of doped BaTiO3 Ceramics. in Program and the Book of Abstracts / Serbian Ceramic Society Conference Advanced Ceramics and Application VI: New Frontiers in Multifunctional Material Science and Processing, Serbia, Belgrade, September 18-20, 2017. 2017;:66-66.
https://hdl.handle.net/21.15107/rcub_dais_2391 .

Đorđević, Miloš, Paunović, Vesna, Mitić, Vojislav V., Prijić, Zoran, Marjanović, Miloš, "Electrical properties of doped BaTiO3 Ceramics" in Program and the Book of Abstracts / Serbian Ceramic Society Conference Advanced Ceramics and Application VI: New Frontiers in Multifunctional Material Science and Processing, Serbia, Belgrade, September 18-20, 2017 (2017):66-66,
https://hdl.handle.net/21.15107/rcub_dais_2391 .

TY  - CONF
AU  - Paunović, Vesna
AU  - Mitić, Vojislav V.
AU  - Kocić, Ljubiša
AU  - Marjanović, Miloš
AU  - Đorđević, Miloš
PY  - 2016
UR  - https://dais.sanu.ac.rs/123456789/875
AB  - The influence of rare-earth additive content on microstructure and electric properties of doped BaTiO3 ceramics is investigated. The concentration of Er2O3 and Yb2O3 in the doped samples range from 0.01 to 1.0at % . The samples are prepared by the conventional solid state reaction, and sintered at 1320° and 1350°C in air atmosphere for 4 hours. SEM analysis shows that all samples are characterized by polygonal grains. The uniform and homogeneous microstructure with grain size ranged from 20 to 45μm is the main low doped samples characteristics. For the samples doped with the higher dopant concentration (0.5 and 1.0 at%) the average grains size is ranged from 5 to 10μm. Dielectric measurements are carried out as a function of temperature up to 180°C at different frequencies. The low doped samples display the high value of dielectric permittivity at room temperature. A nearly flat permittivity-temperature response is obtained in specimens with higher additive content. The Curie temperature of doped samples were ranged from 126 to 130°C. The Curie constant for all series of samples decrease with increment of dopant concentration and the lowest values is mesured from samples doped with 0.01 wt% of aditive. The obtained value of γ pointed out that the specimens have almost sharp phase transition. Also, the specific electrical resistance is measured in function of temperature at the different frequencies from 100Hz to 1MHz. With increasing additives concentration, the electrical resistance decreases to the concentration of 0.5 at% and then increases.
PB  - Belgrade : Serbian Ceramic Society
C3  - Advanced Ceramics and Application : new frontiers in multifunctional material science and processing : program and the book of abstracts : V Serbian Ceramic Society Conference, Sep 21-23 September 2016, Belgrade
T1  - The Rare-Earths influences on doped BaTiO3-Ceramics Microstructure and Electric Characteristics
SP  - 44
EP  - 44
UR  - https://hdl.handle.net/21.15107/rcub_dais_875
ER  - 

@conference{
author = "Paunović, Vesna and Mitić, Vojislav V. and Kocić, Ljubiša and Marjanović, Miloš and Đorđević, Miloš",
year = "2016",
abstract = "The influence of rare-earth additive content on microstructure and electric properties of doped BaTiO3 ceramics is investigated. The concentration of Er2O3 and Yb2O3 in the doped samples range from 0.01 to 1.0at % . The samples are prepared by the conventional solid state reaction, and sintered at 1320° and 1350°C in air atmosphere for 4 hours. SEM analysis shows that all samples are characterized by polygonal grains. The uniform and homogeneous microstructure with grain size ranged from 20 to 45μm is the main low doped samples characteristics. For the samples doped with the higher dopant concentration (0.5 and 1.0 at%) the average grains size is ranged from 5 to 10μm. Dielectric measurements are carried out as a function of temperature up to 180°C at different frequencies. The low doped samples display the high value of dielectric permittivity at room temperature. A nearly flat permittivity-temperature response is obtained in specimens with higher additive content. The Curie temperature of doped samples were ranged from 126 to 130°C. The Curie constant for all series of samples decrease with increment of dopant concentration and the lowest values is mesured from samples doped with 0.01 wt% of aditive. The obtained value of γ pointed out that the specimens have almost sharp phase transition. Also, the specific electrical resistance is measured in function of temperature at the different frequencies from 100Hz to 1MHz. With increasing additives concentration, the electrical resistance decreases to the concentration of 0.5 at% and then increases.",
publisher = "Belgrade : Serbian Ceramic Society",
journal = "Advanced Ceramics and Application : new frontiers in multifunctional material science and processing : program and the book of abstracts : V Serbian Ceramic Society Conference, Sep 21-23 September 2016, Belgrade",
title = "The Rare-Earths influences on doped BaTiO3-Ceramics Microstructure and Electric Characteristics",
pages = "44-44",
url = "https://hdl.handle.net/21.15107/rcub_dais_875"
}

Paunović, V., Mitić, V. V., Kocić, L., Marjanović, M.,& Đorđević, M.. (2016). The Rare-Earths influences on doped BaTiO3-Ceramics Microstructure and Electric Characteristics. in Advanced Ceramics and Application : new frontiers in multifunctional material science and processing : program and the book of abstracts : V Serbian Ceramic Society Conference, Sep 21-23 September 2016, Belgrade
Belgrade : Serbian Ceramic Society., 44-44.
https://hdl.handle.net/21.15107/rcub_dais_875

Paunović V, Mitić VV, Kocić L, Marjanović M, Đorđević M. The Rare-Earths influences on doped BaTiO3-Ceramics Microstructure and Electric Characteristics. in Advanced Ceramics and Application : new frontiers in multifunctional material science and processing : program and the book of abstracts : V Serbian Ceramic Society Conference, Sep 21-23 September 2016, Belgrade. 2016;:44-44.
https://hdl.handle.net/21.15107/rcub_dais_875 .

Paunović, Vesna, Mitić, Vojislav V., Kocić, Ljubiša, Marjanović, Miloš, Đorđević, Miloš, "The Rare-Earths influences on doped BaTiO3-Ceramics Microstructure and Electric Characteristics" in Advanced Ceramics and Application : new frontiers in multifunctional material science and processing : program and the book of abstracts : V Serbian Ceramic Society Conference, Sep 21-23 September 2016, Belgrade (2016):44-44,
https://hdl.handle.net/21.15107/rcub_dais_875 .

TY  - CONF
AU  - Stanković, Maja
AU  - Krstić, Nenad
AU  - Đorđević, Dragan
AU  - Đorđević, Miloš
AU  - Topličić Ćurčić, Gordana
AU  - Mitić, Vojislav V.
PY  - 2016
UR  - https://dais.sanu.ac.rs/123456789/878
AB  - The aim of this study was mineralogical and chemical analysis of mortar from the floor, ceiling and wall of Stibadium B, from the archaeological site of Mediana. ICP-OES and FTIR-spectroscopy were used to determine chemical composition and some major mineralogical species. The obtained results show that lime mortar is probably used. Large contribution of silicon- and aluminum-oxides, indicate the presence of quartz and clay minerals derived from the aggregate, river sand and crushed bricks. The obtained results also show large amount of iron, manganese and copper. The determinated metals in samples from floor and wall of Stibadium B, are mostly present in oxide fraction, while in sample from ceiling, they are mostly found in silicate fraction.
PB  - Belgrade : Serbian Ceramic Society
C3  - Advanced Ceramics and Application : new frontiers in multifunctional material science and processing : program and the book of abstracts : V Serbian Ceramic Society Conference, Sep 21-23 September 2016, Belgrade
T1  - Chemical Analysis of Mortars of Archeological Samples form Mediana
SP  - 80
EP  - 80
UR  - https://hdl.handle.net/21.15107/rcub_dais_878
ER  - 

@conference{
author = "Stanković, Maja and Krstić, Nenad and Đorđević, Dragan and Đorđević, Miloš and Topličić Ćurčić, Gordana and Mitić, Vojislav V.",
year = "2016",
abstract = "The aim of this study was mineralogical and chemical analysis of mortar from the floor, ceiling and wall of Stibadium B, from the archaeological site of Mediana. ICP-OES and FTIR-spectroscopy were used to determine chemical composition and some major mineralogical species. The obtained results show that lime mortar is probably used. Large contribution of silicon- and aluminum-oxides, indicate the presence of quartz and clay minerals derived from the aggregate, river sand and crushed bricks. The obtained results also show large amount of iron, manganese and copper. The determinated metals in samples from floor and wall of Stibadium B, are mostly present in oxide fraction, while in sample from ceiling, they are mostly found in silicate fraction.",
publisher = "Belgrade : Serbian Ceramic Society",
journal = "Advanced Ceramics and Application : new frontiers in multifunctional material science and processing : program and the book of abstracts : V Serbian Ceramic Society Conference, Sep 21-23 September 2016, Belgrade",
title = "Chemical Analysis of Mortars of Archeological Samples form Mediana",
pages = "80-80",
url = "https://hdl.handle.net/21.15107/rcub_dais_878"
}

Stanković, M., Krstić, N., Đorđević, D., Đorđević, M., Topličić Ćurčić, G.,& Mitić, V. V.. (2016). Chemical Analysis of Mortars of Archeological Samples form Mediana. in Advanced Ceramics and Application : new frontiers in multifunctional material science and processing : program and the book of abstracts : V Serbian Ceramic Society Conference, Sep 21-23 September 2016, Belgrade
Belgrade : Serbian Ceramic Society., 80-80.
https://hdl.handle.net/21.15107/rcub_dais_878

Stanković M, Krstić N, Đorđević D, Đorđević M, Topličić Ćurčić G, Mitić VV. Chemical Analysis of Mortars of Archeological Samples form Mediana. in Advanced Ceramics and Application : new frontiers in multifunctional material science and processing : program and the book of abstracts : V Serbian Ceramic Society Conference, Sep 21-23 September 2016, Belgrade. 2016;:80-80.
https://hdl.handle.net/21.15107/rcub_dais_878 .

Stanković, Maja, Krstić, Nenad, Đorđević, Dragan, Đorđević, Miloš, Topličić Ćurčić, Gordana, Mitić, Vojislav V., "Chemical Analysis of Mortars of Archeological Samples form Mediana" in Advanced Ceramics and Application : new frontiers in multifunctional material science and processing : program and the book of abstracts : V Serbian Ceramic Society Conference, Sep 21-23 September 2016, Belgrade (2016):80-80,
https://hdl.handle.net/21.15107/rcub_dais_878 .

TY  - CONF
AU  - Marjanović, Miloš
AU  - Đorđević, Miloš
AU  - Paunović, Vesna
AU  - Mitić, Vojislav V.
PY  - 2014
UR  - https://dais.sanu.ac.rs/123456789/609
AB  - The Nb doped BaTiO3 ceramics, with different Nb2O5 content, ranging from 0.5 to 2.0 at% Nb, were investigated regarding their electrical characteristics in this paper. Nb/BaTiO3 ceramics using in this investigation were prepared by the conventional solid state reaction and sintered at 1320°C in an air atmosphere for 2 hours. The dielectric characteristic of doped BaTiO3 ceramics like as dielectric constant, dissipation factor, impedance (resistance, reactance) have been done by using LCR-Meter Agilent 4284A in the frequency range 20 Hz-1 MHz and Agilent E4991A RF Impedance/Material Analyzer for high frequency measurements (1 MHz – 3 GHz). Dielectric constant and tangent losses after initial large values remains nearly independent of frequency greater than 3 kHz. Dielectric measurements were carried out as a function of temperature up to 180°C. The low doped samples sintered at 1320°C, display the high value of dielectric permittivity at room temperature, 2600 for 0.5Nb/BaTiO3. A nearly flat permittivity-temperature response was obtained in specimens with 2.0 at% additive content. The Curie-Weiss and modified Curie-Weiss law is used to clarify the influence of dopant on the dielectric properties and BaTiO3 phase transformation. All investigated samples have an electrical resistivity ρ >105 Ωcm at room temperature.
PB  - Belgrade : Serbian Ceramic Society
C3  - Advanced Ceramics and Application : new frontiers in multifunctional material science and processing : program and the book of abstracts / III Serbian Ceramic Society Conference, 29th September - 1st October, Belgrade, 2014
T1  - The Electrical Characteristics of Nb doped BaTiO3 Ceramics
SP  - 105
EP  - 105
UR  - https://hdl.handle.net/21.15107/rcub_dais_609
ER  - 

@conference{
author = "Marjanović, Miloš and Đorđević, Miloš and Paunović, Vesna and Mitić, Vojislav V.",
year = "2014",
abstract = "The Nb doped BaTiO3 ceramics, with different Nb2O5 content, ranging from 0.5 to 2.0 at% Nb, were investigated regarding their electrical characteristics in this paper. Nb/BaTiO3 ceramics using in this investigation were prepared by the conventional solid state reaction and sintered at 1320°C in an air atmosphere for 2 hours. The dielectric characteristic of doped BaTiO3 ceramics like as dielectric constant, dissipation factor, impedance (resistance, reactance) have been done by using LCR-Meter Agilent 4284A in the frequency range 20 Hz-1 MHz and Agilent E4991A RF Impedance/Material Analyzer for high frequency measurements (1 MHz – 3 GHz). Dielectric constant and tangent losses after initial large values remains nearly independent of frequency greater than 3 kHz. Dielectric measurements were carried out as a function of temperature up to 180°C. The low doped samples sintered at 1320°C, display the high value of dielectric permittivity at room temperature, 2600 for 0.5Nb/BaTiO3. A nearly flat permittivity-temperature response was obtained in specimens with 2.0 at% additive content. The Curie-Weiss and modified Curie-Weiss law is used to clarify the influence of dopant on the dielectric properties and BaTiO3 phase transformation. All investigated samples have an electrical resistivity ρ >105 Ωcm at room temperature.",
publisher = "Belgrade : Serbian Ceramic Society",
journal = "Advanced Ceramics and Application : new frontiers in multifunctional material science and processing : program and the book of abstracts / III Serbian Ceramic Society Conference, 29th September - 1st October, Belgrade, 2014",
title = "The Electrical Characteristics of Nb doped BaTiO3 Ceramics",
pages = "105-105",
url = "https://hdl.handle.net/21.15107/rcub_dais_609"
}

Marjanović, M., Đorđević, M., Paunović, V.,& Mitić, V. V.. (2014). The Electrical Characteristics of Nb doped BaTiO3 Ceramics. in Advanced Ceramics and Application : new frontiers in multifunctional material science and processing : program and the book of abstracts / III Serbian Ceramic Society Conference, 29th September - 1st October, Belgrade, 2014
Belgrade : Serbian Ceramic Society., 105-105.
https://hdl.handle.net/21.15107/rcub_dais_609

Marjanović M, Đorđević M, Paunović V, Mitić VV. The Electrical Characteristics of Nb doped BaTiO3 Ceramics. in Advanced Ceramics and Application : new frontiers in multifunctional material science and processing : program and the book of abstracts / III Serbian Ceramic Society Conference, 29th September - 1st October, Belgrade, 2014. 2014;:105-105.
https://hdl.handle.net/21.15107/rcub_dais_609 .

Marjanović, Miloš, Đorđević, Miloš, Paunović, Vesna, Mitić, Vojislav V., "The Electrical Characteristics of Nb doped BaTiO3 Ceramics" in Advanced Ceramics and Application : new frontiers in multifunctional material science and processing : program and the book of abstracts / III Serbian Ceramic Society Conference, 29th September - 1st October, Belgrade, 2014 (2014):105-105,
https://hdl.handle.net/21.15107/rcub_dais_609 .