TY  - JOUR
AU  - Luković Golić, Danijela
AU  - Radojković, Aleksandar
AU  - Ćirković, Jovana
AU  - Dapčević, Aleksandra
AU  - Pajić, Damir
AU  - Tasić, Nikola B.
AU  - Savić, Slavica M.
AU  - Počuča Nešić, Milica
AU  - Marković, Smilja
AU  - Branković, Goran
AU  - Marinković Stanojević, Zorica
AU  - Branković, Zorica
PY  - 2016
UR  - https://dais.sanu.ac.rs/123456789/2320
AB  - BiFeO3 powders were synthesized by sonochemically assisted hydrothermal and hydro-evaporation methods. The X-ray diffraction confirmed the presence of secondary phases, Bi25FeO39 and Bi2Fe4O9, in as prepared BiFeO3 powders. Optimization of sintering conditions indicated that temperature of 800 °C and time of 2 h after pressing at 9 t/cm2 provided ceramics samples with the highest density (up to 96% of theoretical density) and the lowest content of secondary phases. Ferroelectric and magnetic characterization was performed on two selected ceramics samples with the highest densities. Ceramics obtained from the powder synthesized by the hydrothermal method showed greater lattice distortion along [1 1 1] axis and smaller grains, which resulted in larger values of electric polarization at room temperature. It also exhibited less Fe(3d)–O(2p) orbital overlapping due to a larger FeOFe bond angle, causing lower antiferromagnetic ordering and weak ferromagnetic behavior at low temperatures.
PB  - Elsevier
T2  - Journal of the European Ceramic Society
T1  - Structural, ferroelectric and magnetic properties of BiFeO3 synthesized by sonochemically assisted hydrothermal and hydro-evaporation chemical methods
SP  - 1623
EP  - 1631
VL  - 36
IS  - 7
DO  - 10.1016/j.jeurceramsoc.2016.01.031
UR  - https://hdl.handle.net/21.15107/rcub_dais_2320
ER  - 

@article{
author = "Luković Golić, Danijela and Radojković, Aleksandar and Ćirković, Jovana and Dapčević, Aleksandra and Pajić, Damir and Tasić, Nikola B. and Savić, Slavica M. and Počuča Nešić, Milica and Marković, Smilja and Branković, Goran and Marinković Stanojević, Zorica and Branković, Zorica",
year = "2016",
abstract = "BiFeO3 powders were synthesized by sonochemically assisted hydrothermal and hydro-evaporation methods. The X-ray diffraction confirmed the presence of secondary phases, Bi25FeO39 and Bi2Fe4O9, in as prepared BiFeO3 powders. Optimization of sintering conditions indicated that temperature of 800 °C and time of 2 h after pressing at 9 t/cm2 provided ceramics samples with the highest density (up to 96% of theoretical density) and the lowest content of secondary phases. Ferroelectric and magnetic characterization was performed on two selected ceramics samples with the highest densities. Ceramics obtained from the powder synthesized by the hydrothermal method showed greater lattice distortion along [1 1 1] axis and smaller grains, which resulted in larger values of electric polarization at room temperature. It also exhibited less Fe(3d)–O(2p) orbital overlapping due to a larger FeOFe bond angle, causing lower antiferromagnetic ordering and weak ferromagnetic behavior at low temperatures.",
publisher = "Elsevier",
journal = "Journal of the European Ceramic Society",
title = "Structural, ferroelectric and magnetic properties of BiFeO3 synthesized by sonochemically assisted hydrothermal and hydro-evaporation chemical methods",
pages = "1623-1631",
volume = "36",
number = "7",
doi = "10.1016/j.jeurceramsoc.2016.01.031",
url = "https://hdl.handle.net/21.15107/rcub_dais_2320"
}

Luković Golić, D., Radojković, A., Ćirković, J., Dapčević, A., Pajić, D., Tasić, N. B., Savić, S. M., Počuča Nešić, M., Marković, S., Branković, G., Marinković Stanojević, Z.,& Branković, Z.. (2016). Structural, ferroelectric and magnetic properties of BiFeO3 synthesized by sonochemically assisted hydrothermal and hydro-evaporation chemical methods. in Journal of the European Ceramic Society
Elsevier., 36(7), 1623-1631.
https://doi.org/10.1016/j.jeurceramsoc.2016.01.031
https://hdl.handle.net/21.15107/rcub_dais_2320

Luković Golić D, Radojković A, Ćirković J, Dapčević A, Pajić D, Tasić NB, Savić SM, Počuča Nešić M, Marković S, Branković G, Marinković Stanojević Z, Branković Z. Structural, ferroelectric and magnetic properties of BiFeO3 synthesized by sonochemically assisted hydrothermal and hydro-evaporation chemical methods. in Journal of the European Ceramic Society. 2016;36(7):1623-1631.
doi:10.1016/j.jeurceramsoc.2016.01.031
https://hdl.handle.net/21.15107/rcub_dais_2320 .

Luković Golić, Danijela, Radojković, Aleksandar, Ćirković, Jovana, Dapčević, Aleksandra, Pajić, Damir, Tasić, Nikola B., Savić, Slavica M., Počuča Nešić, Milica, Marković, Smilja, Branković, Goran, Marinković Stanojević, Zorica, Branković, Zorica, "Structural, ferroelectric and magnetic properties of BiFeO3 synthesized by sonochemically assisted hydrothermal and hydro-evaporation chemical methods" in Journal of the European Ceramic Society, 36, no. 7 (2016):1623-1631,
https://doi.org/10.1016/j.jeurceramsoc.2016.01.031 .,
https://hdl.handle.net/21.15107/rcub_dais_2320 .

TY  - CONF
AU  - Savić, Slavica M.
AU  - Tadić, Marin
AU  - Jagličić, Zvonko
AU  - Mančić, Lidija
AU  - Vojisavljević, Katarina
AU  - Branković, Goran
PY  - 2015
UR  - https://dais.sanu.ac.rs/123456789/742
AB  - Spinel materials based on Mn and Ni has been intensively studied over the past years due to their excellent semiconductor properties. Nickel manganite as NTC thermistor is widely used today in different industrial sectors. Here we report the complex polymerization method (CPM) for producing nickel manganite fine particles with a homogeneous distribution of constituent cations in the crystal lattice that ensures formation of dense monophased ceramic with the novel magnetic properties after been sintered in oxygen and air atmosphere. Phase composition of the synthesized materials was examined by XRPD, while the morphology of the powder and microstructure of ceramic were investigated using FESEM and SEM analyses, respectively. The magnetic properties of the samples have been studied by measuring the temperature and field dependence of magnetization. Magnetic measurements of M(T) reveal rather complex magnetic properties and multiple magnetic phase transitions. In the case of air atmosphere we found three magnetic phase transitions with transition temperatures at TM1=35 K, TM2=101 K and TM3=120 K. TM1 maximum is strongly dependent on the strength of the applied magnetic field (TM1 decreases with increasing applied field) whereas the TM3 is field independent The values of the coercivity, remanent magnetization and saturation magnetization at 100 K are: HC = 184 Oe, Mr = 1.92 emu/g and MS = 7.88 emu/g, respectively. The measured values at 5 K are HC = 1035 Oe, Mr = 7.70 emu/g and MS = 14.47 emu/g. Moreover, hysteresis properties measured after cooling of the sample in magnetic field show exchange bias effect with an exchange bias field |HEB=196 Oe. For the sample synthetized in oxygen atmosphere, the magnetization dependence of temperature M(T) and AC susceptibility data obtained from SQUID measurements clearly demonstrates that quadruple magnetic phase transitions can be readily detected at TM1~115 K, TM2~105 K, TM3~38 K and TM4~7 K. These findings suggest the novel magnetic transition for nickel manganite at low temperature TM4. The temperatures of observed maximums in χ’(T) and χ’’(T) parts of susceptibility are frequency independent, whereas the height of the peaks decreases with increasing frequency. The fact that TM4 does not shift with the increase of the frequency led us to the conclusion that there are no spin-glass/surface effect and/or blocking temperature/finite size effect connected to the NiMn2O4 ceramic. Therefore, the low-temperature peak TM4 in AC susceptibility is associated with ferromagnetic-like and antiferromagnetic-like magnetic transition in the interfacial FM/AFM internal structure. The exchange bias effect was found in a field cooled hysteresis loops at 5 K. The field cooling of the sample was under a magnetic field of 100 Oe and 10 kOe whereas the determined exchange bias fields were |HEB|=129 Oe and 182 Oe, respectively. The analysis of the results and comparison with literature data allowed us to conjecture that the mixed oxidation states of Mn ions and ferromagnetic and antiferromagnetic sublattice orders tailor these interesting magnetic properties.
PB  - Belgrade : Institute for Multidisciplinary Research
C3  - Programme and the Book of Abstracts / 3rd Conference of the Serbian Society for Ceramic Materials, 3CSCS-2015, June 15-17, 2015, Belgrade, Serbia
T1  - Magnetic properties of nickel manganite obtained by a complex polymerization method
SP  - 111
EP  - 112
UR  - https://hdl.handle.net/21.15107/rcub_dais_742
ER  - 

@conference{
author = "Savić, Slavica M. and Tadić, Marin and Jagličić, Zvonko and Mančić, Lidija and Vojisavljević, Katarina and Branković, Goran",
year = "2015",
abstract = "Spinel materials based on Mn and Ni has been intensively studied over the past years due to their excellent semiconductor properties. Nickel manganite as NTC thermistor is widely used today in different industrial sectors. Here we report the complex polymerization method (CPM) for producing nickel manganite fine particles with a homogeneous distribution of constituent cations in the crystal lattice that ensures formation of dense monophased ceramic with the novel magnetic properties after been sintered in oxygen and air atmosphere. Phase composition of the synthesized materials was examined by XRPD, while the morphology of the powder and microstructure of ceramic were investigated using FESEM and SEM analyses, respectively. The magnetic properties of the samples have been studied by measuring the temperature and field dependence of magnetization. Magnetic measurements of M(T) reveal rather complex magnetic properties and multiple magnetic phase transitions. In the case of air atmosphere we found three magnetic phase transitions with transition temperatures at TM1=35 K, TM2=101 K and TM3=120 K. TM1 maximum is strongly dependent on the strength of the applied magnetic field (TM1 decreases with increasing applied field) whereas the TM3 is field independent The values of the coercivity, remanent magnetization and saturation magnetization at 100 K are: HC = 184 Oe, Mr = 1.92 emu/g and MS = 7.88 emu/g, respectively. The measured values at 5 K are HC = 1035 Oe, Mr = 7.70 emu/g and MS = 14.47 emu/g. Moreover, hysteresis properties measured after cooling of the sample in magnetic field show exchange bias effect with an exchange bias field |HEB=196 Oe. For the sample synthetized in oxygen atmosphere, the magnetization dependence of temperature M(T) and AC susceptibility data obtained from SQUID measurements clearly demonstrates that quadruple magnetic phase transitions can be readily detected at TM1~115 K, TM2~105 K, TM3~38 K and TM4~7 K. These findings suggest the novel magnetic transition for nickel manganite at low temperature TM4. The temperatures of observed maximums in χ’(T) and χ’’(T) parts of susceptibility are frequency independent, whereas the height of the peaks decreases with increasing frequency. The fact that TM4 does not shift with the increase of the frequency led us to the conclusion that there are no spin-glass/surface effect and/or blocking temperature/finite size effect connected to the NiMn2O4 ceramic. Therefore, the low-temperature peak TM4 in AC susceptibility is associated with ferromagnetic-like and antiferromagnetic-like magnetic transition in the interfacial FM/AFM internal structure. The exchange bias effect was found in a field cooled hysteresis loops at 5 K. The field cooling of the sample was under a magnetic field of 100 Oe and 10 kOe whereas the determined exchange bias fields were |HEB|=129 Oe and 182 Oe, respectively. The analysis of the results and comparison with literature data allowed us to conjecture that the mixed oxidation states of Mn ions and ferromagnetic and antiferromagnetic sublattice orders tailor these interesting magnetic properties.",
publisher = "Belgrade : Institute for Multidisciplinary Research",
journal = "Programme and the Book of Abstracts / 3rd Conference of the Serbian Society for Ceramic Materials, 3CSCS-2015, June 15-17, 2015, Belgrade, Serbia",
title = "Magnetic properties of nickel manganite obtained by a complex polymerization method",
pages = "111-112",
url = "https://hdl.handle.net/21.15107/rcub_dais_742"
}

Savić, S. M., Tadić, M., Jagličić, Z., Mančić, L., Vojisavljević, K.,& Branković, G.. (2015). Magnetic properties of nickel manganite obtained by a complex polymerization method. in Programme and the Book of Abstracts / 3rd Conference of the Serbian Society for Ceramic Materials, 3CSCS-2015, June 15-17, 2015, Belgrade, Serbia
Belgrade : Institute for Multidisciplinary Research., 111-112.
https://hdl.handle.net/21.15107/rcub_dais_742

Savić SM, Tadić M, Jagličić Z, Mančić L, Vojisavljević K, Branković G. Magnetic properties of nickel manganite obtained by a complex polymerization method. in Programme and the Book of Abstracts / 3rd Conference of the Serbian Society for Ceramic Materials, 3CSCS-2015, June 15-17, 2015, Belgrade, Serbia. 2015;:111-112.
https://hdl.handle.net/21.15107/rcub_dais_742 .

Savić, Slavica M., Tadić, Marin, Jagličić, Zvonko, Mančić, Lidija, Vojisavljević, Katarina, Branković, Goran, "Magnetic properties of nickel manganite obtained by a complex polymerization method" in Programme and the Book of Abstracts / 3rd Conference of the Serbian Society for Ceramic Materials, 3CSCS-2015, June 15-17, 2015, Belgrade, Serbia (2015):111-112,
https://hdl.handle.net/21.15107/rcub_dais_742 .

TY  - JOUR
AU  - Pontón, Patricia I.
AU  - D'Almeida, Jose Roberto
AU  - Marinković, Bojan
AU  - Savić, Slavica M.
AU  - Mančić, Lidija
AU  - Rey, Nicolás
AU  - Morgado, Edisson Jr.
AU  - Rizzo, Fernando C.
PY  - 2014
UR  - https://dais.sanu.ac.rs/123456789/565
AB  - One of the major challenges in the development of nanocomposites based on a polymer matrix and highly polar ceramic nanofillers is the lack of the compatibility between these two components. In order to improve the chemical interaction between titanate nanotubes (TTNT) and polymer matrix, such as nylon 11,3-aminopropyltriethoxysilane (APTES) was grafted onto TTNT. The effects of the TTNT chemical composition i.e. sodium content and solvent type on the grafting silane efficiency were thoroughly studied through CHN elemental analysis, Fourier transform infrared spectroscopy (FTIR), thermogravimetric analysis (TGA), transmission electron microscopy (TEM), surface area and zeta potential measurements. The present study brings evidences supporting aqueous ethanol as more efficient reaction medium for TTNT functionalization with APTES, independent of the sodium content of nanotubes, when compared with pure water. It is also worth noting that within aqueous ethanol medium, TTNT with low sodium content are more efficiently grafted than TTNT with high sodium content. Successful APTES grafting decreases concentration of the hydroxyl groups on TTNT surfaces and enables its future application for the fabrication of nylon 11 nanocomposites.
PB  - Elsevier
T2  - Applied Surface Science
T1  - The effects of the chemical composition of titanate nanotubes and solvent type on 3-aminopropyltriethoxysilane grafting efficiency
SP  - 315
EP  - 322
VL  - 301
DO  - 10.1016/j.apsusc.2014.02.071
UR  - https://hdl.handle.net/21.15107/rcub_dais_565
ER  - 

@article{
author = "Pontón, Patricia I. and D'Almeida, Jose Roberto and Marinković, Bojan and Savić, Slavica M. and Mančić, Lidija and Rey, Nicolás and Morgado, Edisson Jr. and Rizzo, Fernando C.",
year = "2014",
abstract = "One of the major challenges in the development of nanocomposites based on a polymer matrix and highly polar ceramic nanofillers is the lack of the compatibility between these two components. In order to improve the chemical interaction between titanate nanotubes (TTNT) and polymer matrix, such as nylon 11,3-aminopropyltriethoxysilane (APTES) was grafted onto TTNT. The effects of the TTNT chemical composition i.e. sodium content and solvent type on the grafting silane efficiency were thoroughly studied through CHN elemental analysis, Fourier transform infrared spectroscopy (FTIR), thermogravimetric analysis (TGA), transmission electron microscopy (TEM), surface area and zeta potential measurements. The present study brings evidences supporting aqueous ethanol as more efficient reaction medium for TTNT functionalization with APTES, independent of the sodium content of nanotubes, when compared with pure water. It is also worth noting that within aqueous ethanol medium, TTNT with low sodium content are more efficiently grafted than TTNT with high sodium content. Successful APTES grafting decreases concentration of the hydroxyl groups on TTNT surfaces and enables its future application for the fabrication of nylon 11 nanocomposites.",
publisher = "Elsevier",
journal = "Applied Surface Science",
title = "The effects of the chemical composition of titanate nanotubes and solvent type on 3-aminopropyltriethoxysilane grafting efficiency",
pages = "315-322",
volume = "301",
doi = "10.1016/j.apsusc.2014.02.071",
url = "https://hdl.handle.net/21.15107/rcub_dais_565"
}

Pontón, P. I., D'Almeida, J. R., Marinković, B., Savić, S. M., Mančić, L., Rey, N., Morgado, E. Jr.,& Rizzo, F. C.. (2014). The effects of the chemical composition of titanate nanotubes and solvent type on 3-aminopropyltriethoxysilane grafting efficiency. in Applied Surface Science
Elsevier., 301, 315-322.
https://doi.org/10.1016/j.apsusc.2014.02.071
https://hdl.handle.net/21.15107/rcub_dais_565

Pontón PI, D'Almeida JR, Marinković B, Savić SM, Mančić L, Rey N, Morgado EJ, Rizzo FC. The effects of the chemical composition of titanate nanotubes and solvent type on 3-aminopropyltriethoxysilane grafting efficiency. in Applied Surface Science. 2014;301:315-322.
doi:10.1016/j.apsusc.2014.02.071
https://hdl.handle.net/21.15107/rcub_dais_565 .

Pontón, Patricia I., D'Almeida, Jose Roberto, Marinković, Bojan, Savić, Slavica M., Mančić, Lidija, Rey, Nicolás, Morgado, Edisson Jr., Rizzo, Fernando C., "The effects of the chemical composition of titanate nanotubes and solvent type on 3-aminopropyltriethoxysilane grafting efficiency" in Applied Surface Science, 301 (2014):315-322,
https://doi.org/10.1016/j.apsusc.2014.02.071 .,
https://hdl.handle.net/21.15107/rcub_dais_565 .

TY  - JOUR
AU  - Savić, Slavica M.
AU  - Tadić, Marin
AU  - Jagličić, Zvonko
AU  - Vojisavljević, Katarina
AU  - Mančić, Lidija
AU  - Branković, Goran
PY  - 2014
UR  - https://dais.sanu.ac.rs/123456789/662
AB  - Structural, electrical and magnetic properties of nickel manganite ceramics obtained by sintering fine powders prepared by a complex polymerization method are given in this work. The phase composition of the synthesized material was examined by x-ray powder diffraction (XRPD). Field-emission scanning electron microscopy (FE-SEM) was used to analyze the obtained powder morphology. Scanning electron microscopy (SEM) was used to analyze the microstructure of sintered ceramics. The activation energy of conduction Ea and the coefficient of temperature sensitivity B25/100 were calculated from direct current (DC) resistivity measurements. The magnetization dependence of temperature M(T) and alternating current (AC) susceptibility data obtained from SQUID measurements clearly demonstrate that quadruple magnetic phase transitions can be readily detected at TM1~115 K, TM2~105 K, TM3~38 K and TM4~7 K. These findings suggest a novel magnetic transition for nickel manganite at low temperature TM4.
PB  - Elsevier
T2  - Ceramics International
T1  - Structural, electrical and magnetic properties of nickel manganite obtained by a complex polymerization method
SP  - 15515
EP  - 15521
VL  - 40
IS  - 10, Part A
DO  - 10.1016/j.ceramint.2014.07.024
UR  - https://hdl.handle.net/21.15107/rcub_dais_662
ER  - 

@article{
author = "Savić, Slavica M. and Tadić, Marin and Jagličić, Zvonko and Vojisavljević, Katarina and Mančić, Lidija and Branković, Goran",
year = "2014",
abstract = "Structural, electrical and magnetic properties of nickel manganite ceramics obtained by sintering fine powders prepared by a complex polymerization method are given in this work. The phase composition of the synthesized material was examined by x-ray powder diffraction (XRPD). Field-emission scanning electron microscopy (FE-SEM) was used to analyze the obtained powder morphology. Scanning electron microscopy (SEM) was used to analyze the microstructure of sintered ceramics. The activation energy of conduction Ea and the coefficient of temperature sensitivity B25/100 were calculated from direct current (DC) resistivity measurements. The magnetization dependence of temperature M(T) and alternating current (AC) susceptibility data obtained from SQUID measurements clearly demonstrate that quadruple magnetic phase transitions can be readily detected at TM1~115 K, TM2~105 K, TM3~38 K and TM4~7 K. These findings suggest a novel magnetic transition for nickel manganite at low temperature TM4.",
publisher = "Elsevier",
journal = "Ceramics International",
title = "Structural, electrical and magnetic properties of nickel manganite obtained by a complex polymerization method",
pages = "15515-15521",
volume = "40",
number = "10, Part A",
doi = "10.1016/j.ceramint.2014.07.024",
url = "https://hdl.handle.net/21.15107/rcub_dais_662"
}

Savić, S. M., Tadić, M., Jagličić, Z., Vojisavljević, K., Mančić, L.,& Branković, G.. (2014). Structural, electrical and magnetic properties of nickel manganite obtained by a complex polymerization method. in Ceramics International
Elsevier., 40(10, Part A), 15515-15521.
https://doi.org/10.1016/j.ceramint.2014.07.024
https://hdl.handle.net/21.15107/rcub_dais_662

Savić SM, Tadić M, Jagličić Z, Vojisavljević K, Mančić L, Branković G. Structural, electrical and magnetic properties of nickel manganite obtained by a complex polymerization method. in Ceramics International. 2014;40(10, Part A):15515-15521.
doi:10.1016/j.ceramint.2014.07.024
https://hdl.handle.net/21.15107/rcub_dais_662 .

Savić, Slavica M., Tadić, Marin, Jagličić, Zvonko, Vojisavljević, Katarina, Mančić, Lidija, Branković, Goran, "Structural, electrical and magnetic properties of nickel manganite obtained by a complex polymerization method" in Ceramics International, 40, no. 10, Part A (2014):15515-15521,
https://doi.org/10.1016/j.ceramint.2014.07.024 .,
https://hdl.handle.net/21.15107/rcub_dais_662 .

TY  - CONF
AU  - Rizzo, Fernando C.
AU  - Patton, Patricia
AU  - Fortini, Renata
AU  - Marinković, Bojan
AU  - D'Almeida, Jose Roberto
AU  - Mančić, Lidija
AU  - Savić, Slavica M.
PY  - 2013
UR  - https://dais.sanu.ac.rs/123456789/818
AB  - The purpose of the present study was to investigate the effect of titanate nanotubes (TINTs) dispersion in the mechanical properties of Nylon 11 (polyamide 11) polymer. According ,to the existing literature small amounts of TTNTs used as reinforcement in polymer matrix improve properties such as tensile strength and stiffness. However, the addition of these nanoparticles may also lead to a decrease of strength of the composite if the nanotubes are not well dispersed in the polymer matrix. In this work two different routes were investigated to enhance the disl?ersion of TTNTs used as a reinforcement of nylon matrix nanocomposites: (1) chemical functionalization with 3-arninopropyltriethoxysilane; and (2) treatment with 2 kinds of surfactant - a cationic (CTAB) and an anionic (SDS). Characterization of the nanotubes was done by infrared spectroscopy, CHN elemental analysis, measurement of the specific surface area, thermogravimetric analysis, scanning electron microscopy and transmission electron microscopy. Nylon-II matrix nanocomposites were manufactured by microextrusion-microinjection and reinforced with 0.5 to 2.0 wt.-% of functionalized and surfactant treated nanotubes. Finally, mechanical and thermal properties as well as the microstructure of the nanocomposites were evaluated. The presentation will discuss the results and potential applications of these materials.
PB  - Las Vegas
C3  - THERMEC'2013: International Conference on Processing & Manufacturing of Advanced Materials (Processing, Fabrication, Properties, Application), Rio Hotel, Las Vegas, USA, December 2-6, 2013: Book of Abstracts
T1  - Enhancement of titanate nanotubes dispersion for reinforcement of nylon-II nanocomposites
SP  - 67
EP  - 67
UR  - https://hdl.handle.net/21.15107/rcub_dais_818
ER  - 

@conference{
author = "Rizzo, Fernando C. and Patton, Patricia and Fortini, Renata and Marinković, Bojan and D'Almeida, Jose Roberto and Mančić, Lidija and Savić, Slavica M.",
year = "2013",
abstract = "The purpose of the present study was to investigate the effect of titanate nanotubes (TINTs) dispersion in the mechanical properties of Nylon 11 (polyamide 11) polymer. According ,to the existing literature small amounts of TTNTs used as reinforcement in polymer matrix improve properties such as tensile strength and stiffness. However, the addition of these nanoparticles may also lead to a decrease of strength of the composite if the nanotubes are not well dispersed in the polymer matrix. In this work two different routes were investigated to enhance the disl?ersion of TTNTs used as a reinforcement of nylon matrix nanocomposites: (1) chemical functionalization with 3-arninopropyltriethoxysilane; and (2) treatment with 2 kinds of surfactant - a cationic (CTAB) and an anionic (SDS). Characterization of the nanotubes was done by infrared spectroscopy, CHN elemental analysis, measurement of the specific surface area, thermogravimetric analysis, scanning electron microscopy and transmission electron microscopy. Nylon-II matrix nanocomposites were manufactured by microextrusion-microinjection and reinforced with 0.5 to 2.0 wt.-% of functionalized and surfactant treated nanotubes. Finally, mechanical and thermal properties as well as the microstructure of the nanocomposites were evaluated. The presentation will discuss the results and potential applications of these materials.",
publisher = "Las Vegas",
journal = "THERMEC'2013: International Conference on Processing & Manufacturing of Advanced Materials (Processing, Fabrication, Properties, Application), Rio Hotel, Las Vegas, USA, December 2-6, 2013: Book of Abstracts",
title = "Enhancement of titanate nanotubes dispersion for reinforcement of nylon-II nanocomposites",
pages = "67-67",
url = "https://hdl.handle.net/21.15107/rcub_dais_818"
}

Rizzo, F. C., Patton, P., Fortini, R., Marinković, B., D'Almeida, J. R., Mančić, L.,& Savić, S. M.. (2013). Enhancement of titanate nanotubes dispersion for reinforcement of nylon-II nanocomposites. in THERMEC'2013: International Conference on Processing & Manufacturing of Advanced Materials (Processing, Fabrication, Properties, Application), Rio Hotel, Las Vegas, USA, December 2-6, 2013: Book of Abstracts
Las Vegas., 67-67.
https://hdl.handle.net/21.15107/rcub_dais_818

Rizzo FC, Patton P, Fortini R, Marinković B, D'Almeida JR, Mančić L, Savić SM. Enhancement of titanate nanotubes dispersion for reinforcement of nylon-II nanocomposites. in THERMEC'2013: International Conference on Processing & Manufacturing of Advanced Materials (Processing, Fabrication, Properties, Application), Rio Hotel, Las Vegas, USA, December 2-6, 2013: Book of Abstracts. 2013;:67-67.
https://hdl.handle.net/21.15107/rcub_dais_818 .

Rizzo, Fernando C., Patton, Patricia, Fortini, Renata, Marinković, Bojan, D'Almeida, Jose Roberto, Mančić, Lidija, Savić, Slavica M., "Enhancement of titanate nanotubes dispersion for reinforcement of nylon-II nanocomposites" in THERMEC'2013: International Conference on Processing & Manufacturing of Advanced Materials (Processing, Fabrication, Properties, Application), Rio Hotel, Las Vegas, USA, December 2-6, 2013: Book of Abstracts (2013):67-67,
https://hdl.handle.net/21.15107/rcub_dais_818 .

TY  - CONF
AU  - Pontón, Patricia I.
AU  - Mančić, Lidija
AU  - Savić, Slavica M.
AU  - Marinković, Bojan
PY  - 2013
UR  - https://dais.sanu.ac.rs/123456789/408
AB  - In order to develop new nanosized filler compatible with the thermoplastic polymer Nyion-11, trititanate nanotubes (TTNTs) were synthesized by standard alkaline hydrothermal treatment of a TiO2 anatase powder in 10 M NaOH at 120 DC for 24 h. After the synthesis, the as-obtained nanopowder was washed differently (either with water or HC1), in order to prepare TTNTs with high and low sodium contents. Chemical functionalization of TTNTs was performed with 3-minopropyltriethoxisilane (APTES) coupling agent using two different reaction media (water and an ethanol/water mixture) with the aim to improve the bonding between inorganic hydrophilic fillers and hydrophobic polymer matrix. Fourier transform infrared spectroscopy (FTIR), thermogravimetry analysis (TGA), transmission electron microscopy (TEM), zeta potential and CHN elemental analyses were used to elucidate the grafting mechanism of APTES at TTNTs surface. The obtained results shown that: APTES coupling agent is bounded covalently to the TTNTs surface (Ti-O-Si bond was identified after deconvolution of the IR bands at 800-1000 cm-1); grafted amount of APTES is almost independent of the reaction media; protonation of-NH2 groups shift the isoelectric point from pH 2.4 to pH 6.6; TTNTs kept their original size and shape after silanization.
PB  - Belgrade : Institute for Multidisciplinary Research
C3  - 2nd Conference of the Serbian Ceramic Society, 2CSCS-2013, June 5-7, 2013, Belgrade, Serbia :  Programme and th e book of abstracts
T1  - Functionalization of the titanate nanotubes with a silane coupling agent
SP  - 65
EP  - 66
UR  - https://hdl.handle.net/21.15107/rcub_dais_408
ER  - 

@conference{
author = "Pontón, Patricia I. and Mančić, Lidija and Savić, Slavica M. and Marinković, Bojan",
year = "2013",
abstract = "In order to develop new nanosized filler compatible with the thermoplastic polymer Nyion-11, trititanate nanotubes (TTNTs) were synthesized by standard alkaline hydrothermal treatment of a TiO2 anatase powder in 10 M NaOH at 120 DC for 24 h. After the synthesis, the as-obtained nanopowder was washed differently (either with water or HC1), in order to prepare TTNTs with high and low sodium contents. Chemical functionalization of TTNTs was performed with 3-minopropyltriethoxisilane (APTES) coupling agent using two different reaction media (water and an ethanol/water mixture) with the aim to improve the bonding between inorganic hydrophilic fillers and hydrophobic polymer matrix. Fourier transform infrared spectroscopy (FTIR), thermogravimetry analysis (TGA), transmission electron microscopy (TEM), zeta potential and CHN elemental analyses were used to elucidate the grafting mechanism of APTES at TTNTs surface. The obtained results shown that: APTES coupling agent is bounded covalently to the TTNTs surface (Ti-O-Si bond was identified after deconvolution of the IR bands at 800-1000 cm-1); grafted amount of APTES is almost independent of the reaction media; protonation of-NH2 groups shift the isoelectric point from pH 2.4 to pH 6.6; TTNTs kept their original size and shape after silanization.",
publisher = "Belgrade : Institute for Multidisciplinary Research",
journal = "2nd Conference of the Serbian Ceramic Society, 2CSCS-2013, June 5-7, 2013, Belgrade, Serbia :  Programme and th e book of abstracts",
title = "Functionalization of the titanate nanotubes with a silane coupling agent",
pages = "65-66",
url = "https://hdl.handle.net/21.15107/rcub_dais_408"
}

Pontón, P. I., Mančić, L., Savić, S. M.,& Marinković, B.. (2013). Functionalization of the titanate nanotubes with a silane coupling agent. in 2nd Conference of the Serbian Ceramic Society, 2CSCS-2013, June 5-7, 2013, Belgrade, Serbia :  Programme and th e book of abstracts
Belgrade : Institute for Multidisciplinary Research., 65-66.
https://hdl.handle.net/21.15107/rcub_dais_408

Pontón PI, Mančić L, Savić SM, Marinković B. Functionalization of the titanate nanotubes with a silane coupling agent. in 2nd Conference of the Serbian Ceramic Society, 2CSCS-2013, June 5-7, 2013, Belgrade, Serbia :  Programme and th e book of abstracts. 2013;:65-66.
https://hdl.handle.net/21.15107/rcub_dais_408 .

Pontón, Patricia I., Mančić, Lidija, Savić, Slavica M., Marinković, Bojan, "Functionalization of the titanate nanotubes with a silane coupling agent" in 2nd Conference of the Serbian Ceramic Society, 2CSCS-2013, June 5-7, 2013, Belgrade, Serbia :  Programme and th e book of abstracts (2013):65-66,
https://hdl.handle.net/21.15107/rcub_dais_408 .

TY  - JOUR
AU  - Savić, Slavica M.
AU  - Stojanović, G. M.
AU  - Nikolić, Maria Vesna
AU  - Aleksić, Obrad S.
AU  - Luković Golić, Danijela
AU  - Nikolić, Pantelija M.
PY  - 2009
UR  - https://dais.sanu.ac.rs/123456789/3467
AB  - Intrinsic resistivity and carrier transport parameters of sintered nickel manganite samples (NTC thermistor grade) were determined using a Hall effect measurement system based on the van der Pauw method. Powder mixtures composed of MnO, NiO and with small amounts of CoO and Fe 2O 3 were free surface energy activated by milling in an ultra fast planetary mill for 5, 15, 30, 45 and 60 min. The powders were uniaxially pressed with 196 MPa into discs and sintered at 1200 °C for 60 min. Full characterization of nickel manganite samples was done using SEM, EDS and XRD analysis. The Hall effect was measured at different temperatures (room temperature, 50, 80, 100 and 120 °C) with an applied field of 0.37 T and also 0.57 T at room temperature. The activation energy E a (energy of conduction) and the coefficient of temperature sensitivity B 25/80, were calculated from measured resistivity values. The measured mobility, resistivity/conductivity, U-I plots, and Hall coefficients were mutually compared and correlated versus microstructure development and macroscopic parameters such as the powder activation time and ambient temperature. © Springer Science+Business Media, LLC 2008.
PB  - Springer
T2  - Journal of Materials Science: Materials in Electronics
T1  - Electrical and transport properties of nickel manganite obtained by Hall effect measurements
SP  - 242
EP  - 247
VL  - 20
IS  - 3
DO  - 10.1007/s10854-008-9710-5
UR  - https://hdl.handle.net/21.15107/rcub_dais_3467
ER  - 

@article{
author = "Savić, Slavica M. and Stojanović, G. M. and Nikolić, Maria Vesna and Aleksić, Obrad S. and Luković Golić, Danijela and Nikolić, Pantelija M.",
year = "2009",
abstract = "Intrinsic resistivity and carrier transport parameters of sintered nickel manganite samples (NTC thermistor grade) were determined using a Hall effect measurement system based on the van der Pauw method. Powder mixtures composed of MnO, NiO and with small amounts of CoO and Fe 2O 3 were free surface energy activated by milling in an ultra fast planetary mill for 5, 15, 30, 45 and 60 min. The powders were uniaxially pressed with 196 MPa into discs and sintered at 1200 °C for 60 min. Full characterization of nickel manganite samples was done using SEM, EDS and XRD analysis. The Hall effect was measured at different temperatures (room temperature, 50, 80, 100 and 120 °C) with an applied field of 0.37 T and also 0.57 T at room temperature. The activation energy E a (energy of conduction) and the coefficient of temperature sensitivity B 25/80, were calculated from measured resistivity values. The measured mobility, resistivity/conductivity, U-I plots, and Hall coefficients were mutually compared and correlated versus microstructure development and macroscopic parameters such as the powder activation time and ambient temperature. © Springer Science+Business Media, LLC 2008.",
publisher = "Springer",
journal = "Journal of Materials Science: Materials in Electronics",
title = "Electrical and transport properties of nickel manganite obtained by Hall effect measurements",
pages = "242-247",
volume = "20",
number = "3",
doi = "10.1007/s10854-008-9710-5",
url = "https://hdl.handle.net/21.15107/rcub_dais_3467"
}

Savić, S. M., Stojanović, G. M., Nikolić, M. V., Aleksić, O. S., Luković Golić, D.,& Nikolić, P. M.. (2009). Electrical and transport properties of nickel manganite obtained by Hall effect measurements. in Journal of Materials Science: Materials in Electronics
Springer., 20(3), 242-247.
https://doi.org/10.1007/s10854-008-9710-5
https://hdl.handle.net/21.15107/rcub_dais_3467

Savić SM, Stojanović GM, Nikolić MV, Aleksić OS, Luković Golić D, Nikolić PM. Electrical and transport properties of nickel manganite obtained by Hall effect measurements. in Journal of Materials Science: Materials in Electronics. 2009;20(3):242-247.
doi:10.1007/s10854-008-9710-5
https://hdl.handle.net/21.15107/rcub_dais_3467 .

Savić, Slavica M., Stojanović, G. M., Nikolić, Maria Vesna, Aleksić, Obrad S., Luković Golić, Danijela, Nikolić, Pantelija M., "Electrical and transport properties of nickel manganite obtained by Hall effect measurements" in Journal of Materials Science: Materials in Electronics, 20, no. 3 (2009):242-247,
https://doi.org/10.1007/s10854-008-9710-5 .,
https://hdl.handle.net/21.15107/rcub_dais_3467 .

TY  - JOUR
AU  - Nikolić, Maria Vesna
AU  - Obradović, Nina
AU  - Paraskevopoulos, Konstantinos M.
AU  - Zorba, Triantafyllia T.
AU  - Savić, Slavica M.
AU  - Ristić, Momčilo M.
PY  - 2009
UR  - https://dais.sanu.ac.rs/123456789/3460
AB  - The starting mixtures of ZnO, TiO2, and MgO (0, 1.25, and 2.5 wt.%) powders are mechanically activated in a high-energy planetary mill for 15 min and then sintered between 800 and 1100°C for 2 h. The influence of MgO addition on the structure of the samples obtained is analyzed with X-ray diffraction and infrared reflection spectroscopy. Room-temperature far-infrared reflectivity spectra of the samples doped with MgO (0, 1.25, and 2.5 wt.%) and sintered at 1100 °C in the frequency range between 100 and 1200 cm- 1 are measured and analyzed. Optical parameters are determined for seven oscillators belonging to the spinel structure using the four-parameter model of coupled oscillators. Born effective charges are calculated from the transversal/longitudinal splitting. © 2009 Springer Science+Business Media, Inc.
PB  - Springer
T2  - Powder Metallurgy and Metal Ceramics
T1  - Structural analysis of Zn2TiO4 doped with MgO
SP  - 712
EP  - 717
VL  - 48
IS  - 11-12
DO  - 10.1007/s11106-010-9190-z
UR  - https://hdl.handle.net/21.15107/rcub_dais_3460
ER  - 

@article{
author = "Nikolić, Maria Vesna and Obradović, Nina and Paraskevopoulos, Konstantinos M. and Zorba, Triantafyllia T. and Savić, Slavica M. and Ristić, Momčilo M.",
year = "2009",
abstract = "The starting mixtures of ZnO, TiO2, and MgO (0, 1.25, and 2.5 wt.%) powders are mechanically activated in a high-energy planetary mill for 15 min and then sintered between 800 and 1100°C for 2 h. The influence of MgO addition on the structure of the samples obtained is analyzed with X-ray diffraction and infrared reflection spectroscopy. Room-temperature far-infrared reflectivity spectra of the samples doped with MgO (0, 1.25, and 2.5 wt.%) and sintered at 1100 °C in the frequency range between 100 and 1200 cm- 1 are measured and analyzed. Optical parameters are determined for seven oscillators belonging to the spinel structure using the four-parameter model of coupled oscillators. Born effective charges are calculated from the transversal/longitudinal splitting. © 2009 Springer Science+Business Media, Inc.",
publisher = "Springer",
journal = "Powder Metallurgy and Metal Ceramics",
title = "Structural analysis of Zn2TiO4 doped with MgO",
pages = "712-717",
volume = "48",
number = "11-12",
doi = "10.1007/s11106-010-9190-z",
url = "https://hdl.handle.net/21.15107/rcub_dais_3460"
}

Nikolić, M. V., Obradović, N., Paraskevopoulos, K. M., Zorba, T. T., Savić, S. M.,& Ristić, M. M.. (2009). Structural analysis of Zn2TiO4 doped with MgO. in Powder Metallurgy and Metal Ceramics
Springer., 48(11-12), 712-717.
https://doi.org/10.1007/s11106-010-9190-z
https://hdl.handle.net/21.15107/rcub_dais_3460

Nikolić MV, Obradović N, Paraskevopoulos KM, Zorba TT, Savić SM, Ristić MM. Structural analysis of Zn2TiO4 doped with MgO. in Powder Metallurgy and Metal Ceramics. 2009;48(11-12):712-717.
doi:10.1007/s11106-010-9190-z
https://hdl.handle.net/21.15107/rcub_dais_3460 .

Nikolić, Maria Vesna, Obradović, Nina, Paraskevopoulos, Konstantinos M., Zorba, Triantafyllia T., Savić, Slavica M., Ristić, Momčilo M., "Structural analysis of Zn2TiO4 doped with MgO" in Powder Metallurgy and Metal Ceramics, 48, no. 11-12 (2009):712-717,
https://doi.org/10.1007/s11106-010-9190-z .,
https://hdl.handle.net/21.15107/rcub_dais_3460 .

TY  - JOUR
AU  - Nikolić, Pantelija M.
AU  - Luković, Danijela
AU  - Savić, Slavica M.
AU  - Milovanović, A. M.
AU  - Dukić, S. R.
AU  - Nikolić, Maria Vesna
AU  - Stamenović, Bojana
PY  - 2008
UR  - https://dais.sanu.ac.rs/123456789/3592
AB  - The thermal diffusivity and free carrier diffusion coefficient of 12CaO×7 Al2O3 (C12A7) sintered for different times in air or hydrogen followed by treatment with UV light were determined from photoacoustic phase and amplitude spectra obtained using the photoacoustic method with a transmission detection configuration. The influence of the sintering time on the values of the obtained parameters was analyzed and also the different sintering procedures. © EDP Sciences/Societé Italiana di Fisica/Springer-Verlag 2008.
PB  - Springer
T2  - European Physical Journal: Special Topics
T1  - Thermal diffusivity of sintered 12CaO×7AI2O3
SP  - 183
EP  - 186
VL  - 153
IS  - 1
DO  - 10.1140/epjst/e2008-00423-7
UR  - https://hdl.handle.net/21.15107/rcub_dais_3592
ER  - 

@article{
author = "Nikolić, Pantelija M. and Luković, Danijela and Savić, Slavica M. and Milovanović, A. M. and Dukić, S. R. and Nikolić, Maria Vesna and Stamenović, Bojana",
year = "2008",
abstract = "The thermal diffusivity and free carrier diffusion coefficient of 12CaO×7 Al2O3 (C12A7) sintered for different times in air or hydrogen followed by treatment with UV light were determined from photoacoustic phase and amplitude spectra obtained using the photoacoustic method with a transmission detection configuration. The influence of the sintering time on the values of the obtained parameters was analyzed and also the different sintering procedures. © EDP Sciences/Societé Italiana di Fisica/Springer-Verlag 2008.",
publisher = "Springer",
journal = "European Physical Journal: Special Topics",
title = "Thermal diffusivity of sintered 12CaO×7AI2O3",
pages = "183-186",
volume = "153",
number = "1",
doi = "10.1140/epjst/e2008-00423-7",
url = "https://hdl.handle.net/21.15107/rcub_dais_3592"
}

Nikolić, P. M., Luković, D., Savić, S. M., Milovanović, A. M., Dukić, S. R., Nikolić, M. V.,& Stamenović, B.. (2008). Thermal diffusivity of sintered 12CaO×7AI2O3. in European Physical Journal: Special Topics
Springer., 153(1), 183-186.
https://doi.org/10.1140/epjst/e2008-00423-7
https://hdl.handle.net/21.15107/rcub_dais_3592

Nikolić PM, Luković D, Savić SM, Milovanović AM, Dukić SR, Nikolić MV, Stamenović B. Thermal diffusivity of sintered 12CaO×7AI2O3. in European Physical Journal: Special Topics. 2008;153(1):183-186.
doi:10.1140/epjst/e2008-00423-7
https://hdl.handle.net/21.15107/rcub_dais_3592 .

Nikolić, Pantelija M., Luković, Danijela, Savić, Slavica M., Milovanović, A. M., Dukić, S. R., Nikolić, Maria Vesna, Stamenović, Bojana, "Thermal diffusivity of sintered 12CaO×7AI2O3" in European Physical Journal: Special Topics, 153, no. 1 (2008):183-186,
https://doi.org/10.1140/epjst/e2008-00423-7 .,
https://hdl.handle.net/21.15107/rcub_dais_3592 .

TY  - JOUR
AU  - Nikolić, Pantelija M.
AU  - Luković, Danijela
AU  - Nikolić, Maria Vesna
AU  - Đurić, S.
AU  - Savić, Slavica M.
AU  - Milovanović, A. M.
AU  - Dukić, S. R.
AU  - Stamenović, Bojana
PY  - 2008
UR  - https://dais.sanu.ac.rs/123456789/3589
AB  - A single p-type crystal of the mineral, pyrite (FeS2) was characterized photoacoustically using the transmission detection configuration. Photoacoustic (PA) amplitude and phase spectra were measured using a specially constructed PA cell. The PA signals of different sample thicknesses were measured using an experimental setup with a semiconductor red laser (80 mW) as the optical source. The obtained amplitude and phase spectra for different thicknesses were numerically analyzed enabling determination of thermal diffusivity, mobility of minority free carriers and other parameters characteristic for this material. © EDP Sciences/Societé Italiana di Fisica/Springer-Verlag 2008.
PB  - Springer
T2  - European Physical Journal: Special Topics
T1  - Photoacoustic characterization of natural mineral pyrite (FeS2)
SP  - 187
EP  - 189
VL  - 153
IS  - 1
DO  - 10.1140/epjst/e2008-00424-6
UR  - https://hdl.handle.net/21.15107/rcub_dais_3589
ER  - 

@article{
author = "Nikolić, Pantelija M. and Luković, Danijela and Nikolić, Maria Vesna and Đurić, S. and Savić, Slavica M. and Milovanović, A. M. and Dukić, S. R. and Stamenović, Bojana",
year = "2008",
abstract = "A single p-type crystal of the mineral, pyrite (FeS2) was characterized photoacoustically using the transmission detection configuration. Photoacoustic (PA) amplitude and phase spectra were measured using a specially constructed PA cell. The PA signals of different sample thicknesses were measured using an experimental setup with a semiconductor red laser (80 mW) as the optical source. The obtained amplitude and phase spectra for different thicknesses were numerically analyzed enabling determination of thermal diffusivity, mobility of minority free carriers and other parameters characteristic for this material. © EDP Sciences/Societé Italiana di Fisica/Springer-Verlag 2008.",
publisher = "Springer",
journal = "European Physical Journal: Special Topics",
title = "Photoacoustic characterization of natural mineral pyrite (FeS2)",
pages = "187-189",
volume = "153",
number = "1",
doi = "10.1140/epjst/e2008-00424-6",
url = "https://hdl.handle.net/21.15107/rcub_dais_3589"
}

Nikolić, P. M., Luković, D., Nikolić, M. V., Đurić, S., Savić, S. M., Milovanović, A. M., Dukić, S. R.,& Stamenović, B.. (2008). Photoacoustic characterization of natural mineral pyrite (FeS2). in European Physical Journal: Special Topics
Springer., 153(1), 187-189.
https://doi.org/10.1140/epjst/e2008-00424-6
https://hdl.handle.net/21.15107/rcub_dais_3589

Nikolić PM, Luković D, Nikolić MV, Đurić S, Savić SM, Milovanović AM, Dukić SR, Stamenović B. Photoacoustic characterization of natural mineral pyrite (FeS2). in European Physical Journal: Special Topics. 2008;153(1):187-189.
doi:10.1140/epjst/e2008-00424-6
https://hdl.handle.net/21.15107/rcub_dais_3589 .

Nikolić, Pantelija M., Luković, Danijela, Nikolić, Maria Vesna, Đurić, S., Savić, Slavica M., Milovanović, A. M., Dukić, S. R., Stamenović, Bojana, "Photoacoustic characterization of natural mineral pyrite (FeS2)" in European Physical Journal: Special Topics, 153, no. 1 (2008):187-189,
https://doi.org/10.1140/epjst/e2008-00424-6 .,
https://hdl.handle.net/21.15107/rcub_dais_3589 .

TY  - JOUR
AU  - Savić, Slavica M.
AU  - Nikolić, Maria Vesna
AU  - Aleksić, Obrad S.
AU  - Slankamenac, Miloš
AU  - Živanov, M.
AU  - Nikolić, Pantelija M.
PY  - 2008
UR  - https://dais.sanu.ac.rs/123456789/208
AB  - In this work the DC resistivity of sintered nickel manganite NiMn2O4 (NTC thermistor material) was studied as a function of additional powder activation time in a planetary ball mill (0, 5, 15, 30, 45 and 60 min). The activated powders and non-activated powder were sintered at different temperatures (900, 1050 and 12000C) for an hour. Structural changes were analyzed using XRD. Sample density, porosity and DC resistivity were measured on the same sintered samples. Correlations between sample density, porosity, and intrinsic DC resistivity vs. additional powder activation time and the sintering temperature were made. It was noticed that the resistivity falls with the increase of sample density (or increase of the sintering temperature).
PB  - Belgrade : International Institute for the Science of Sintering
T2  - Science of Sintering
T1  - Intrinsic resistivity of sintered Nickel Manganite vs. powder activation time and density
SP  - 27
EP  - 32
VL  - 40
IS  - 1
DO  - 10.2298/SOS0801027S
UR  - https://hdl.handle.net/21.15107/rcub_dais_208
ER  - 

@article{
author = "Savić, Slavica M. and Nikolić, Maria Vesna and Aleksić, Obrad S. and Slankamenac, Miloš and Živanov, M. and Nikolić, Pantelija M.",
year = "2008",
abstract = "In this work the DC resistivity of sintered nickel manganite NiMn2O4 (NTC thermistor material) was studied as a function of additional powder activation time in a planetary ball mill (0, 5, 15, 30, 45 and 60 min). The activated powders and non-activated powder were sintered at different temperatures (900, 1050 and 12000C) for an hour. Structural changes were analyzed using XRD. Sample density, porosity and DC resistivity were measured on the same sintered samples. Correlations between sample density, porosity, and intrinsic DC resistivity vs. additional powder activation time and the sintering temperature were made. It was noticed that the resistivity falls with the increase of sample density (or increase of the sintering temperature).",
publisher = "Belgrade : International Institute for the Science of Sintering",
journal = "Science of Sintering",
title = "Intrinsic resistivity of sintered Nickel Manganite vs. powder activation time and density",
pages = "27-32",
volume = "40",
number = "1",
doi = "10.2298/SOS0801027S",
url = "https://hdl.handle.net/21.15107/rcub_dais_208"
}

Savić, S. M., Nikolić, M. V., Aleksić, O. S., Slankamenac, M., Živanov, M.,& Nikolić, P. M.. (2008). Intrinsic resistivity of sintered Nickel Manganite vs. powder activation time and density. in Science of Sintering
Belgrade : International Institute for the Science of Sintering., 40(1), 27-32.
https://doi.org/10.2298/SOS0801027S
https://hdl.handle.net/21.15107/rcub_dais_208

Savić SM, Nikolić MV, Aleksić OS, Slankamenac M, Živanov M, Nikolić PM. Intrinsic resistivity of sintered Nickel Manganite vs. powder activation time and density. in Science of Sintering. 2008;40(1):27-32.
doi:10.2298/SOS0801027S
https://hdl.handle.net/21.15107/rcub_dais_208 .

Savić, Slavica M., Nikolić, Maria Vesna, Aleksić, Obrad S., Slankamenac, Miloš, Živanov, M., Nikolić, Pantelija M., "Intrinsic resistivity of sintered Nickel Manganite vs. powder activation time and density" in Science of Sintering, 40, no. 1 (2008):27-32,
https://doi.org/10.2298/SOS0801027S .,
https://hdl.handle.net/21.15107/rcub_dais_208 .

TY  - CONF
AU  - Menićanin, Aleksandar B.
AU  - Aleksić, Obrad S.
AU  - Nikolić, Maria Vesna
AU  - Savić, Slavica M.
AU  - Radojčić, B. M.
PY  - 2008
UR  - https://dais.sanu.ac.rs/123456789/3572
AB  - A novel uniaxial anemometer was created using a NTC thick film segmented thermistor to measure wind speed and direction. The anemometer operated on the principle of heat loss caused by the air volume flow and air speed. A NTC segmented thermistor served as a wind sensor in the anemometer. It was self-heated by a DC constant voltage. The self-heated DC current through the thermistor was changed by heat loss due to resistivity changes. The wind speed was varied from 1 to 15 m/s for different input air temperatures in the range of -20 to +40°C. The wind direction was determined by measuring voltage differences on the inner electrodes of the NTC segmented thermistor. The air temperature was measure by a cold NTC thick film segmented thermistor calibrated in the claim chamber. Anemometar inertia was measured at room temperature (at 25°C) and normal room humidity (at 50%). The results obtained enable fast optimization and implementation of a uniaxial anemometer in a 3D anemometer. © 2008 IEEE.
PB  - IEEE
C3  - 26th International Conference on Microelectronics, Proceedings, MIEL 2008
T1  - Novel uniaxial anemometer containing NTC thick film segmented thermistors
SP  - 349
EP  - 352
DO  - 10.1109/ICMEL.2008.4559293
UR  - https://hdl.handle.net/21.15107/rcub_dais_3572
ER  - 

@conference{
author = "Menićanin, Aleksandar B. and Aleksić, Obrad S. and Nikolić, Maria Vesna and Savić, Slavica M. and Radojčić, B. M.",
year = "2008",
abstract = "A novel uniaxial anemometer was created using a NTC thick film segmented thermistor to measure wind speed and direction. The anemometer operated on the principle of heat loss caused by the air volume flow and air speed. A NTC segmented thermistor served as a wind sensor in the anemometer. It was self-heated by a DC constant voltage. The self-heated DC current through the thermistor was changed by heat loss due to resistivity changes. The wind speed was varied from 1 to 15 m/s for different input air temperatures in the range of -20 to +40°C. The wind direction was determined by measuring voltage differences on the inner electrodes of the NTC segmented thermistor. The air temperature was measure by a cold NTC thick film segmented thermistor calibrated in the claim chamber. Anemometar inertia was measured at room temperature (at 25°C) and normal room humidity (at 50%). The results obtained enable fast optimization and implementation of a uniaxial anemometer in a 3D anemometer. © 2008 IEEE.",
publisher = "IEEE",
journal = "26th International Conference on Microelectronics, Proceedings, MIEL 2008",
title = "Novel uniaxial anemometer containing NTC thick film segmented thermistors",
pages = "349-352",
doi = "10.1109/ICMEL.2008.4559293",
url = "https://hdl.handle.net/21.15107/rcub_dais_3572"
}

Menićanin, A. B., Aleksić, O. S., Nikolić, M. V., Savić, S. M.,& Radojčić, B. M.. (2008). Novel uniaxial anemometer containing NTC thick film segmented thermistors. in 26th International Conference on Microelectronics, Proceedings, MIEL 2008
IEEE., 349-352.
https://doi.org/10.1109/ICMEL.2008.4559293
https://hdl.handle.net/21.15107/rcub_dais_3572

Menićanin AB, Aleksić OS, Nikolić MV, Savić SM, Radojčić BM. Novel uniaxial anemometer containing NTC thick film segmented thermistors. in 26th International Conference on Microelectronics, Proceedings, MIEL 2008. 2008;:349-352.
doi:10.1109/ICMEL.2008.4559293
https://hdl.handle.net/21.15107/rcub_dais_3572 .

Menićanin, Aleksandar B., Aleksić, Obrad S., Nikolić, Maria Vesna, Savić, Slavica M., Radojčić, B. M., "Novel uniaxial anemometer containing NTC thick film segmented thermistors" in 26th International Conference on Microelectronics, Proceedings, MIEL 2008 (2008):349-352,
https://doi.org/10.1109/ICMEL.2008.4559293 .,
https://hdl.handle.net/21.15107/rcub_dais_3572 .

TY  - JOUR
AU  - Nikolić, Maria Vesna
AU  - Obradović, Nina
AU  - Paraskevopoulos, Konstantinos M.
AU  - Zorba, Triantafyllia T.
AU  - Savić, Slavica M.
AU  - Ristić, Momčilo M.
PY  - 2008
UR  - https://dais.sanu.ac.rs/123456789/3576
AB  - Zinc-titanate ceramics were obtained by initial mechanical activation in a high-energy planetary mill for 15 min followed by sintering at temperatures 900-1100°C for 2 h. Room temperature far infrared reflectivity spectra for all samples were measured in the range 100-1200 cm-1. The same ionic oscillators were present in the measured spectra, but their intensities increased with the sintering temperature in correlation with the increase in sample density and microstructure changes. Optical parameters were determined for seven oscillators belonging to the spinel structure using the four-parameter model of coupled oscillators. Born effective charges were calculated from the transversal/longitudinal splitting. © 2008 Springer Science+Business Media, LLC.
PB  - Springer Science+Business Media
T2  - Journal of Materials Science
T1  - Far infrared reflectance of sintered Zn2TiO4
SP  - 5564
EP  - 5568
VL  - 43
IS  - 16
DO  - 10.1007/s10853-008-2819-3
UR  - https://hdl.handle.net/21.15107/rcub_dais_3576
ER  - 

@article{
author = "Nikolić, Maria Vesna and Obradović, Nina and Paraskevopoulos, Konstantinos M. and Zorba, Triantafyllia T. and Savić, Slavica M. and Ristić, Momčilo M.",
year = "2008",
abstract = "Zinc-titanate ceramics were obtained by initial mechanical activation in a high-energy planetary mill for 15 min followed by sintering at temperatures 900-1100°C for 2 h. Room temperature far infrared reflectivity spectra for all samples were measured in the range 100-1200 cm-1. The same ionic oscillators were present in the measured spectra, but their intensities increased with the sintering temperature in correlation with the increase in sample density and microstructure changes. Optical parameters were determined for seven oscillators belonging to the spinel structure using the four-parameter model of coupled oscillators. Born effective charges were calculated from the transversal/longitudinal splitting. © 2008 Springer Science+Business Media, LLC.",
publisher = "Springer Science+Business Media",
journal = "Journal of Materials Science",
title = "Far infrared reflectance of sintered Zn2TiO4",
pages = "5564-5568",
volume = "43",
number = "16",
doi = "10.1007/s10853-008-2819-3",
url = "https://hdl.handle.net/21.15107/rcub_dais_3576"
}

Nikolić, M. V., Obradović, N., Paraskevopoulos, K. M., Zorba, T. T., Savić, S. M.,& Ristić, M. M.. (2008). Far infrared reflectance of sintered Zn2TiO4. in Journal of Materials Science
Springer Science+Business Media., 43(16), 5564-5568.
https://doi.org/10.1007/s10853-008-2819-3
https://hdl.handle.net/21.15107/rcub_dais_3576

Nikolić MV, Obradović N, Paraskevopoulos KM, Zorba TT, Savić SM, Ristić MM. Far infrared reflectance of sintered Zn2TiO4. in Journal of Materials Science. 2008;43(16):5564-5568.
doi:10.1007/s10853-008-2819-3
https://hdl.handle.net/21.15107/rcub_dais_3576 .

Nikolić, Maria Vesna, Obradović, Nina, Paraskevopoulos, Konstantinos M., Zorba, Triantafyllia T., Savić, Slavica M., Ristić, Momčilo M., "Far infrared reflectance of sintered Zn2TiO4" in Journal of Materials Science, 43, no. 16 (2008):5564-5568,
https://doi.org/10.1007/s10853-008-2819-3 .,
https://hdl.handle.net/21.15107/rcub_dais_3576 .

TY  - JOUR
AU  - Nikolić, Pantelija M.
AU  - Luković, Danijela
AU  - König, Wolfgang
AU  - Nikolić, Maria Vesna
AU  - Blagojević, Vladimir D.
AU  - Vujatović, Stevan S.
AU  - Savić, Slavica M.
AU  - Stamenović, Bojana
PY  - 2008
UR  - https://dais.sanu.ac.rs/123456789/3591
AB  - Far infrared reflectivity spectra of single crystal PbTe samples doped with 0.2 at% Fe were measured in the temperature range between 10 K and 300 K. These spectra show very sharp and narrow dips below 120 cm-1. The experimental data were numerically analyzed using a fitting procedure based on the plasmon-phonon interaction model. Two local modes were observed. The first one was noted between 130 cm-1 and 170 cm-1 depending on the temperature and the second more frequency stable one was noted at about 230 cm-1.
PB  - Măgurele : National Institute of Research and Development for Optoelectronics
T2  - Journal of Optoelectronics and Advanced Materials
T1  - Far infrared properties of iron doped single crystal PbTe
SP  - 145
EP  - 148
VL  - 10
IS  - 1
UR  - https://hdl.handle.net/21.15107/rcub_dais_3591
ER  - 

@article{
author = "Nikolić, Pantelija M. and Luković, Danijela and König, Wolfgang and Nikolić, Maria Vesna and Blagojević, Vladimir D. and Vujatović, Stevan S. and Savić, Slavica M. and Stamenović, Bojana",
year = "2008",
abstract = "Far infrared reflectivity spectra of single crystal PbTe samples doped with 0.2 at% Fe were measured in the temperature range between 10 K and 300 K. These spectra show very sharp and narrow dips below 120 cm-1. The experimental data were numerically analyzed using a fitting procedure based on the plasmon-phonon interaction model. Two local modes were observed. The first one was noted between 130 cm-1 and 170 cm-1 depending on the temperature and the second more frequency stable one was noted at about 230 cm-1.",
publisher = "Măgurele : National Institute of Research and Development for Optoelectronics",
journal = "Journal of Optoelectronics and Advanced Materials",
title = "Far infrared properties of iron doped single crystal PbTe",
pages = "145-148",
volume = "10",
number = "1",
url = "https://hdl.handle.net/21.15107/rcub_dais_3591"
}

Nikolić, P. M., Luković, D., König, W., Nikolić, M. V., Blagojević, V. D., Vujatović, S. S., Savić, S. M.,& Stamenović, B.. (2008). Far infrared properties of iron doped single crystal PbTe. in Journal of Optoelectronics and Advanced Materials
Măgurele : National Institute of Research and Development for Optoelectronics., 10(1), 145-148.
https://hdl.handle.net/21.15107/rcub_dais_3591

Nikolić PM, Luković D, König W, Nikolić MV, Blagojević VD, Vujatović SS, Savić SM, Stamenović B. Far infrared properties of iron doped single crystal PbTe. in Journal of Optoelectronics and Advanced Materials. 2008;10(1):145-148.
https://hdl.handle.net/21.15107/rcub_dais_3591 .

Nikolić, Pantelija M., Luković, Danijela, König, Wolfgang, Nikolić, Maria Vesna, Blagojević, Vladimir D., Vujatović, Stevan S., Savić, Slavica M., Stamenović, Bojana, "Far infrared properties of iron doped single crystal PbTe" in Journal of Optoelectronics and Advanced Materials, 10, no. 1 (2008):145-148,
https://hdl.handle.net/21.15107/rcub_dais_3591 .

TY  - JOUR
AU  - Nikolić, Pantelija
AU  - Vujatović, Stevan
AU  - Paraskevopoulos, Konstantinos M.
AU  - Zorbas, Kostas T.
AU  - Savić, Slavica
AU  - Nikolić, Maria Vesna
AU  - Aleksić, Obrad
AU  - Ristić, Momčilo M.
PY  - 2007
UR  - https://dais.sanu.ac.rs/123456789/15269
AB  - Photoacoustic phase and amplitude spectra of YBa 2 Cu 3 O 7 – δ samples synthesised 18 years ago were measured and numerically analysed. The value of thermal diffusivity obtained on the aged samples was lower than the values obtained for fresh samples. Far infrared spectra of YBa 2 Cu 3 O 7 – δ samples synthesised 18 years ago were recorded and analysed enabling determination of reflectivity peak phonon frequencies present at room temperature. X-ray diffraction analysis and far infrared reflectivity measurements enabled determination of a slight change of the oxygen content with time. The YBa 2 Cu 3 O 7 – δ samples synthesised 18 years ago still remained superconducting, which was confirmed by resistivity measurements of the samples between 50 K and room temperature where the critical temperature was reduced from 93 to 73 K. Atomic force microscopy, scanning electron microscopy and energy dispersive X-ray microanalytical measurements were also performed confirming the composition of the sample.
T2  - International Journal of Materials Research
T1  - Effect of ageing on optical and thermal properties of YBa2Cu3O7–δ
SP  - 569
EP  - 573
VL  - 98
IS  - 7
DO  - 10.3139/146.101511
UR  - https://hdl.handle.net/21.15107/rcub_dais_15269
ER  - 

@article{
author = "Nikolić, Pantelija and Vujatović, Stevan and Paraskevopoulos, Konstantinos M. and Zorbas, Kostas T. and Savić, Slavica and Nikolić, Maria Vesna and Aleksić, Obrad and Ristić, Momčilo M.",
year = "2007",
abstract = "Photoacoustic phase and amplitude spectra of YBa 2 Cu 3 O 7 – δ samples synthesised 18 years ago were measured and numerically analysed. The value of thermal diffusivity obtained on the aged samples was lower than the values obtained for fresh samples. Far infrared spectra of YBa 2 Cu 3 O 7 – δ samples synthesised 18 years ago were recorded and analysed enabling determination of reflectivity peak phonon frequencies present at room temperature. X-ray diffraction analysis and far infrared reflectivity measurements enabled determination of a slight change of the oxygen content with time. The YBa 2 Cu 3 O 7 – δ samples synthesised 18 years ago still remained superconducting, which was confirmed by resistivity measurements of the samples between 50 K and room temperature where the critical temperature was reduced from 93 to 73 K. Atomic force microscopy, scanning electron microscopy and energy dispersive X-ray microanalytical measurements were also performed confirming the composition of the sample.",
journal = "International Journal of Materials Research",
title = "Effect of ageing on optical and thermal properties of YBa2Cu3O7–δ",
pages = "569-573",
volume = "98",
number = "7",
doi = "10.3139/146.101511",
url = "https://hdl.handle.net/21.15107/rcub_dais_15269"
}

Nikolić, P., Vujatović, S., Paraskevopoulos, K. M., Zorbas, K. T., Savić, S., Nikolić, M. V., Aleksić, O.,& Ristić, M. M.. (2007). Effect of ageing on optical and thermal properties of YBa2Cu3O7–δ. in International Journal of Materials Research, 98(7), 569-573.
https://doi.org/10.3139/146.101511
https://hdl.handle.net/21.15107/rcub_dais_15269

Nikolić P, Vujatović S, Paraskevopoulos KM, Zorbas KT, Savić S, Nikolić MV, Aleksić O, Ristić MM. Effect of ageing on optical and thermal properties of YBa2Cu3O7–δ. in International Journal of Materials Research. 2007;98(7):569-573.
doi:10.3139/146.101511
https://hdl.handle.net/21.15107/rcub_dais_15269 .

Nikolić, Pantelija, Vujatović, Stevan, Paraskevopoulos, Konstantinos M., Zorbas, Kostas T., Savić, Slavica, Nikolić, Maria Vesna, Aleksić, Obrad, Ristić, Momčilo M., "Effect of ageing on optical and thermal properties of YBa2Cu3O7–δ" in International Journal of Materials Research, 98, no. 7 (2007):569-573,
https://doi.org/10.3139/146.101511 .,
https://hdl.handle.net/21.15107/rcub_dais_15269 .

TY  - JOUR
AU  - Nikolić, Pantelija
AU  - Đurić, S.
AU  - Paraskevopoulos, Konstantinos M.
AU  - Zorba, Triantafyllia T.
AU  - Luković Golić, Danijela
AU  - Savić, Slavica
AU  - Blagojević, Vladimir
AU  - Nikolić, Maria Vesna
PY  - 2007
UR  - https://dais.sanu.ac.rs/123456789/15228
AB  - Polarized far- and mid-infrared reflectance spectra were measured at room temperature for the new mineral species jarandolite, CaB3O4(OH)(3), for the two principal directions. Thirty three vibration modes for (E) over right arrow parallel to(c) over right arrowc and 32 for (E) over right arrow perpendicular to(c) over right arrow were observed and analysed numerically. Symmetry analysis predicts 41 (E) over right arrow parallel to(c) over right arrow and 40 (E) over right arrow perpendicular to(c) over right arrow vibration modes that include lattice and O-H modes. Mode assignment was made based on the structure of jarandolite. The values of the mode frequencies (omega(TO)), the damping factors (gamma) and the oscillator strength (S) of each oscillator were obtained by fitting to a Lorentz model.
PB  - Twickenham : Mineralogical Soc.
T2  - Mineralogical Magazine
T1  - Infrared reflectance of single-crystal jarandolite, CaB3O4(OH)3
SP  - 273
EP  - 283
VL  - 71
IS  - 3
DO  - 10.1180/minmag.2007.071.3.273
UR  - https://hdl.handle.net/21.15107/rcub_dais_15228
ER  - 

@article{
author = "Nikolić, Pantelija and Đurić, S. and Paraskevopoulos, Konstantinos M. and Zorba, Triantafyllia T. and Luković Golić, Danijela and Savić, Slavica and Blagojević, Vladimir and Nikolić, Maria Vesna",
year = "2007",
abstract = "Polarized far- and mid-infrared reflectance spectra were measured at room temperature for the new mineral species jarandolite, CaB3O4(OH)(3), for the two principal directions. Thirty three vibration modes for (E) over right arrow parallel to(c) over right arrowc and 32 for (E) over right arrow perpendicular to(c) over right arrow were observed and analysed numerically. Symmetry analysis predicts 41 (E) over right arrow parallel to(c) over right arrow and 40 (E) over right arrow perpendicular to(c) over right arrow vibration modes that include lattice and O-H modes. Mode assignment was made based on the structure of jarandolite. The values of the mode frequencies (omega(TO)), the damping factors (gamma) and the oscillator strength (S) of each oscillator were obtained by fitting to a Lorentz model.",
publisher = "Twickenham : Mineralogical Soc.",
journal = "Mineralogical Magazine",
title = "Infrared reflectance of single-crystal jarandolite, CaB3O4(OH)3",
pages = "273-283",
volume = "71",
number = "3",
doi = "10.1180/minmag.2007.071.3.273",
url = "https://hdl.handle.net/21.15107/rcub_dais_15228"
}

Nikolić, P., Đurić, S., Paraskevopoulos, K. M., Zorba, T. T., Luković Golić, D., Savić, S., Blagojević, V.,& Nikolić, M. V.. (2007). Infrared reflectance of single-crystal jarandolite, CaB3O4(OH)3. in Mineralogical Magazine
Twickenham : Mineralogical Soc.., 71(3), 273-283.
https://doi.org/10.1180/minmag.2007.071.3.273
https://hdl.handle.net/21.15107/rcub_dais_15228

Nikolić P, Đurić S, Paraskevopoulos KM, Zorba TT, Luković Golić D, Savić S, Blagojević V, Nikolić MV. Infrared reflectance of single-crystal jarandolite, CaB3O4(OH)3. in Mineralogical Magazine. 2007;71(3):273-283.
doi:10.1180/minmag.2007.071.3.273
https://hdl.handle.net/21.15107/rcub_dais_15228 .

Nikolić, Pantelija, Đurić, S., Paraskevopoulos, Konstantinos M., Zorba, Triantafyllia T., Luković Golić, Danijela, Savić, Slavica, Blagojević, Vladimir, Nikolić, Maria Vesna, "Infrared reflectance of single-crystal jarandolite, CaB3O4(OH)3" in Mineralogical Magazine, 71, no. 3 (2007):273-283,
https://doi.org/10.1180/minmag.2007.071.3.273 .,
https://hdl.handle.net/21.15107/rcub_dais_15228 .

TY  - JOUR
AU  - Nikolić, Maria Vesna
AU  - Paraskevopoulos, Konstantinos M.
AU  - Aleksić, Obrad
AU  - Zorba, Triantafyllia T.
AU  - Savić, Slavica
AU  - Blagojević, Vladimir D.
AU  - Luković, Danijela
AU  - Nikolić, Pantelija M.
PY  - 2007
UR  - https://dais.sanu.ac.rs/123456789/12885
AB  - Single phase complex spinel (Mn, Ni, Co, Fe)(3)O-4 samples were sintered at 1050, 1200 and 1300 degrees C for 30 min and at 1200 degrees C for 120 min. Morphological changes of the obtained samples with the siDtering temperature and time were analyzed by X-ray diffraction and scanning electron microscope (SEM). Room temperature far infrared reflectivity spectra for all samples were measured in the frequency range between 50 and 1200 cm(-1). The obtained spectra for all samples showed the presence of the same oscillators, but their intensities increased with the sintering temperature and time in correlation with the increase in sample density and microstructure changes during sintering. The measured spectra were numerically analyzed using the Kramers-Kronig method and the four-parameter model of coupled oscillators. Optical modes were calculated for six observed ionic oscillators belonging to the spinel structure of (Mn, Ni, Co, Fe)(3)O-4 of which four were strong and two were weak.
PB  - Pergamon-Elsevier Science Ltd, Oxford
T2  - Materials Research Bulletin
T1  - Far infrared reflectance of sintered nickel manganite samples for negative temperature coefficient thermistors
SP  - 1492
EP  - 1498
VL  - 42
IS  - 8
DO  - 10.1016/j.materresbull.2006.11.005
UR  - https://hdl.handle.net/21.15107/rcub_dais_12885
ER  - 

@article{
author = "Nikolić, Maria Vesna and Paraskevopoulos, Konstantinos M. and Aleksić, Obrad and Zorba, Triantafyllia T. and Savić, Slavica and Blagojević, Vladimir D. and Luković, Danijela and Nikolić, Pantelija M.",
year = "2007",
abstract = "Single phase complex spinel (Mn, Ni, Co, Fe)(3)O-4 samples were sintered at 1050, 1200 and 1300 degrees C for 30 min and at 1200 degrees C for 120 min. Morphological changes of the obtained samples with the siDtering temperature and time were analyzed by X-ray diffraction and scanning electron microscope (SEM). Room temperature far infrared reflectivity spectra for all samples were measured in the frequency range between 50 and 1200 cm(-1). The obtained spectra for all samples showed the presence of the same oscillators, but their intensities increased with the sintering temperature and time in correlation with the increase in sample density and microstructure changes during sintering. The measured spectra were numerically analyzed using the Kramers-Kronig method and the four-parameter model of coupled oscillators. Optical modes were calculated for six observed ionic oscillators belonging to the spinel structure of (Mn, Ni, Co, Fe)(3)O-4 of which four were strong and two were weak.",
publisher = "Pergamon-Elsevier Science Ltd, Oxford",
journal = "Materials Research Bulletin",
title = "Far infrared reflectance of sintered nickel manganite samples for negative temperature coefficient thermistors",
pages = "1492-1498",
volume = "42",
number = "8",
doi = "10.1016/j.materresbull.2006.11.005",
url = "https://hdl.handle.net/21.15107/rcub_dais_12885"
}

Nikolić, M. V., Paraskevopoulos, K. M., Aleksić, O., Zorba, T. T., Savić, S., Blagojević, V. D., Luković, D.,& Nikolić, P. M.. (2007). Far infrared reflectance of sintered nickel manganite samples for negative temperature coefficient thermistors. in Materials Research Bulletin
Pergamon-Elsevier Science Ltd, Oxford., 42(8), 1492-1498.
https://doi.org/10.1016/j.materresbull.2006.11.005
https://hdl.handle.net/21.15107/rcub_dais_12885

Nikolić MV, Paraskevopoulos KM, Aleksić O, Zorba TT, Savić S, Blagojević VD, Luković D, Nikolić PM. Far infrared reflectance of sintered nickel manganite samples for negative temperature coefficient thermistors. in Materials Research Bulletin. 2007;42(8):1492-1498.
doi:10.1016/j.materresbull.2006.11.005
https://hdl.handle.net/21.15107/rcub_dais_12885 .

Nikolić, Maria Vesna, Paraskevopoulos, Konstantinos M., Aleksić, Obrad, Zorba, Triantafyllia T., Savić, Slavica, Blagojević, Vladimir D., Luković, Danijela, Nikolić, Pantelija M., "Far infrared reflectance of sintered nickel manganite samples for negative temperature coefficient thermistors" in Materials Research Bulletin, 42, no. 8 (2007):1492-1498,
https://doi.org/10.1016/j.materresbull.2006.11.005 .,
https://hdl.handle.net/21.15107/rcub_dais_12885 .

TY  - JOUR
AU  - Nikolić, Pantelija M.
AU  - Koenig, W.
AU  - Vujatović, Stevan S.
AU  - Blagojević, Vladimir D.
AU  - Luković, Danijela
AU  - Savić, Slavica
AU  - Radulović, K.
AU  - Urošević, Dragan
AU  - Nikolić, Maria Vesna
PY  - 2007
UR  - http://rimsi.imsi.bg.ac.rs/handle/123456789/212
UR  - https://dais.sanu.ac.rs/123456789/12886
AB  - Single crystal samples of lead telluride doped with cerium were made using the Bridgman method. Far infrared reflectivity spectra in the temperature range from 10 to 300K are presented. The experimental data were numerically analyzed using a fitting procedure based on the plasmon-phonon interaction model and optical parameters were determined. Two additional local modes were observed at about 138 and 337 cm(-1). The origin of these local vibrational impurity modes was discussed.
PB  - Lausanne : Elsevier Science
T2  - Journal of Alloys and Compounds
T1  - Far infrared properties of PbTe doped with cerium
SP  - 292
EP  - 295
VL  - 433
IS  - 1-2
DO  - 10.1016/j.jallcom.2006.06.066
UR  - https://hdl.handle.net/21.15107/rcub_dais_12886
ER  - 

@article{
author = "Nikolić, Pantelija M. and Koenig, W. and Vujatović, Stevan S. and Blagojević, Vladimir D. and Luković, Danijela and Savić, Slavica and Radulović, K. and Urošević, Dragan and Nikolić, Maria Vesna",
year = "2007",
abstract = "Single crystal samples of lead telluride doped with cerium were made using the Bridgman method. Far infrared reflectivity spectra in the temperature range from 10 to 300K are presented. The experimental data were numerically analyzed using a fitting procedure based on the plasmon-phonon interaction model and optical parameters were determined. Two additional local modes were observed at about 138 and 337 cm(-1). The origin of these local vibrational impurity modes was discussed.",
publisher = "Lausanne : Elsevier Science",
journal = "Journal of Alloys and Compounds",
title = "Far infrared properties of PbTe doped with cerium",
pages = "292-295",
volume = "433",
number = "1-2",
doi = "10.1016/j.jallcom.2006.06.066",
url = "https://hdl.handle.net/21.15107/rcub_dais_12886"
}

Nikolić, P. M., Koenig, W., Vujatović, S. S., Blagojević, V. D., Luković, D., Savić, S., Radulović, K., Urošević, D.,& Nikolić, M. V.. (2007). Far infrared properties of PbTe doped with cerium. in Journal of Alloys and Compounds
Lausanne : Elsevier Science., 433(1-2), 292-295.
https://doi.org/10.1016/j.jallcom.2006.06.066
https://hdl.handle.net/21.15107/rcub_dais_12886

Nikolić PM, Koenig W, Vujatović SS, Blagojević VD, Luković D, Savić S, Radulović K, Urošević D, Nikolić MV. Far infrared properties of PbTe doped with cerium. in Journal of Alloys and Compounds. 2007;433(1-2):292-295.
doi:10.1016/j.jallcom.2006.06.066
https://hdl.handle.net/21.15107/rcub_dais_12886 .

Nikolić, Pantelija M., Koenig, W., Vujatović, Stevan S., Blagojević, Vladimir D., Luković, Danijela, Savić, Slavica, Radulović, K., Urošević, Dragan, Nikolić, Maria Vesna, "Far infrared properties of PbTe doped with cerium" in Journal of Alloys and Compounds, 433, no. 1-2 (2007):292-295,
https://doi.org/10.1016/j.jallcom.2006.06.066 .,
https://hdl.handle.net/21.15107/rcub_dais_12886 .

TY  - JOUR
AU  - Luković, Danijela
AU  - Nikolić, Pantelija M.
AU  - Vujatović, Stevan S.
AU  - Savić, Slavica M.
AU  - Urošević, Dragan
PY  - 2007
UR  - https://dais.sanu.ac.rs/123456789/215
AB  - Single crystals of PbTe(Ni) were investigated by the photoacoustic method. They were produced using the Bridgeman method. These crystals have a sodium chloride cubic lattice and could be cleaved paralel to the plane orientation (200). They were of the n-type. Phase and amplitude photoacoustic spectra were measured using a transmision detection configuration set-up. Photoacoustic (PA) spectra (single and normalized) were numerically analyzed using the Rosencwaig-Gersho model. Thermal diffusivity and some electron-transport parameters were determined. These results were compared with existing results for pure single crystal PbTe. Thermal difusivity of PbTe(Ni) is a bit higher than the thermal difusivity of pure PbTe. This is the consequence of a decreasing concentration of the majority free carriers in the doped alloy.
PB  - Belgrade : International Institute for the Science of Sintering
T2  - Science of Sintering
T1  - Photoacoustic properties of single crystal PbTe(Ni)
SP  - 161
EP  - 167
VL  - 39
IS  - 2
DO  - 10.2298/SOS0702161L
UR  - https://hdl.handle.net/21.15107/rcub_dais_215
ER  - 

@article{
author = "Luković, Danijela and Nikolić, Pantelija M. and Vujatović, Stevan S. and Savić, Slavica M. and Urošević, Dragan",
year = "2007",
abstract = "Single crystals of PbTe(Ni) were investigated by the photoacoustic method. They were produced using the Bridgeman method. These crystals have a sodium chloride cubic lattice and could be cleaved paralel to the plane orientation (200). They were of the n-type. Phase and amplitude photoacoustic spectra were measured using a transmision detection configuration set-up. Photoacoustic (PA) spectra (single and normalized) were numerically analyzed using the Rosencwaig-Gersho model. Thermal diffusivity and some electron-transport parameters were determined. These results were compared with existing results for pure single crystal PbTe. Thermal difusivity of PbTe(Ni) is a bit higher than the thermal difusivity of pure PbTe. This is the consequence of a decreasing concentration of the majority free carriers in the doped alloy.",
publisher = "Belgrade : International Institute for the Science of Sintering",
journal = "Science of Sintering",
title = "Photoacoustic properties of single crystal PbTe(Ni)",
pages = "161-167",
volume = "39",
number = "2",
doi = "10.2298/SOS0702161L",
url = "https://hdl.handle.net/21.15107/rcub_dais_215"
}

Luković, D., Nikolić, P. M., Vujatović, S. S., Savić, S. M.,& Urošević, D.. (2007). Photoacoustic properties of single crystal PbTe(Ni). in Science of Sintering
Belgrade : International Institute for the Science of Sintering., 39(2), 161-167.
https://doi.org/10.2298/SOS0702161L
https://hdl.handle.net/21.15107/rcub_dais_215

Luković D, Nikolić PM, Vujatović SS, Savić SM, Urošević D. Photoacoustic properties of single crystal PbTe(Ni). in Science of Sintering. 2007;39(2):161-167.
doi:10.2298/SOS0702161L
https://hdl.handle.net/21.15107/rcub_dais_215 .

Luković, Danijela, Nikolić, Pantelija M., Vujatović, Stevan S., Savić, Slavica M., Urošević, Dragan, "Photoacoustic properties of single crystal PbTe(Ni)" in Science of Sintering, 39, no. 2 (2007):161-167,
https://doi.org/10.2298/SOS0702161L .,
https://hdl.handle.net/21.15107/rcub_dais_215 .

TY  - JOUR
AU  - Nikolić, Pantelija M.
AU  - Paraskevopoulos, Konstantinos M.
AU  - Zorba, Triantafyllia T.
AU  - Pavlidou, Eleni
AU  - Kantiranis, N.
AU  - Vujatović, Stevan S.
AU  - Aleksić, Obrad S.
AU  - Nikolić, Maria Vesna
AU  - Ivetić, Tamara
AU  - Savić, Slavica M.
AU  - Labus, Nebojša
AU  - Blagojević, Vladimir D.
PY  - 2007
UR  - https://dais.sanu.ac.rs/123456789/212
AB  - Far infrared spectra of sintered PbTe doped with boron were analyzed. The measured infrared spectra were fitted using a modified plasmon-phonnon interaction model with two additional oscillators (at about 195 cm-1 and 285 cm-1) representing local B-impurity modes. The obtained results were compared with previously published data for a single crystal PbTe sample doped with boron.
PB  - Belgrade : International Institute for the Science of Sintering
T2  - Science of Sintering
T1  - Far infrared properties of sintered PbTe doped with boron
SP  - 223
EP  - 228
VL  - 39
IS  - 3
DO  - 10.2298/SOS0703223N
UR  - https://hdl.handle.net/21.15107/rcub_dais_212
ER  - 

@article{
author = "Nikolić, Pantelija M. and Paraskevopoulos, Konstantinos M. and Zorba, Triantafyllia T. and Pavlidou, Eleni and Kantiranis, N. and Vujatović, Stevan S. and Aleksić, Obrad S. and Nikolić, Maria Vesna and Ivetić, Tamara and Savić, Slavica M. and Labus, Nebojša and Blagojević, Vladimir D.",
year = "2007",
abstract = "Far infrared spectra of sintered PbTe doped with boron were analyzed. The measured infrared spectra were fitted using a modified plasmon-phonnon interaction model with two additional oscillators (at about 195 cm-1 and 285 cm-1) representing local B-impurity modes. The obtained results were compared with previously published data for a single crystal PbTe sample doped with boron.",
publisher = "Belgrade : International Institute for the Science of Sintering",
journal = "Science of Sintering",
title = "Far infrared properties of sintered PbTe doped with boron",
pages = "223-228",
volume = "39",
number = "3",
doi = "10.2298/SOS0703223N",
url = "https://hdl.handle.net/21.15107/rcub_dais_212"
}

Nikolić, P. M., Paraskevopoulos, K. M., Zorba, T. T., Pavlidou, E., Kantiranis, N., Vujatović, S. S., Aleksić, O. S., Nikolić, M. V., Ivetić, T., Savić, S. M., Labus, N.,& Blagojević, V. D.. (2007). Far infrared properties of sintered PbTe doped with boron. in Science of Sintering
Belgrade : International Institute for the Science of Sintering., 39(3), 223-228.
https://doi.org/10.2298/SOS0703223N
https://hdl.handle.net/21.15107/rcub_dais_212

Nikolić PM, Paraskevopoulos KM, Zorba TT, Pavlidou E, Kantiranis N, Vujatović SS, Aleksić OS, Nikolić MV, Ivetić T, Savić SM, Labus N, Blagojević VD. Far infrared properties of sintered PbTe doped with boron. in Science of Sintering. 2007;39(3):223-228.
doi:10.2298/SOS0703223N
https://hdl.handle.net/21.15107/rcub_dais_212 .

Nikolić, Pantelija M., Paraskevopoulos, Konstantinos M., Zorba, Triantafyllia T., Pavlidou, Eleni, Kantiranis, N., Vujatović, Stevan S., Aleksić, Obrad S., Nikolić, Maria Vesna, Ivetić, Tamara, Savić, Slavica M., Labus, Nebojša, Blagojević, Vladimir D., "Far infrared properties of sintered PbTe doped with boron" in Science of Sintering, 39, no. 3 (2007):223-228,
https://doi.org/10.2298/SOS0703223N .,
https://hdl.handle.net/21.15107/rcub_dais_212 .

TY  - CONF
AU  - Savić, Slavica M.
AU  - Nikolić, Maria Vesna
AU  - Aleksić, Obrad S.
AU  - Slankamenac, Miloš
AU  - Živanov, M.
AU  - Nikolić, Pantelija M.
PY  - 2007
UR  - https://dais.sanu.ac.rs/123456789/314
AB  - Poster presented at the conference Fizika i tehnologija materijala (Physics and Technology of Materials), FITEM '07, Čačak, Serbia, August 6-8, 2007.
T1  - Intrinsic resistivity of sintered nickel manganite vs. powder activation time and density
UR  - https://hdl.handle.net/21.15107/rcub_dais_314
ER  - 

@conference{
author = "Savić, Slavica M. and Nikolić, Maria Vesna and Aleksić, Obrad S. and Slankamenac, Miloš and Živanov, M. and Nikolić, Pantelija M.",
year = "2007",
abstract = "Poster presented at the conference Fizika i tehnologija materijala (Physics and Technology of Materials), FITEM '07, Čačak, Serbia, August 6-8, 2007.",
title = "Intrinsic resistivity of sintered nickel manganite vs. powder activation time and density",
url = "https://hdl.handle.net/21.15107/rcub_dais_314"
}

Savić, S. M., Nikolić, M. V., Aleksić, O. S., Slankamenac, M., Živanov, M.,& Nikolić, P. M.. (2007). Intrinsic resistivity of sintered nickel manganite vs. powder activation time and density. .
https://hdl.handle.net/21.15107/rcub_dais_314

Savić SM, Nikolić MV, Aleksić OS, Slankamenac M, Živanov M, Nikolić PM. Intrinsic resistivity of sintered nickel manganite vs. powder activation time and density. 2007;.
https://hdl.handle.net/21.15107/rcub_dais_314 .

Savić, Slavica M., Nikolić, Maria Vesna, Aleksić, Obrad S., Slankamenac, Miloš, Živanov, M., Nikolić, Pantelija M., "Intrinsic resistivity of sintered nickel manganite vs. powder activation time and density" (2007),
https://hdl.handle.net/21.15107/rcub_dais_314 .

TY  - CONF
AU  - Nikolić, Pantelija M.
AU  - Luković, Danijela
AU  - Savić, Slavica M.
AU  - Milovanović, A. M.
AU  - Đukić, S. R.
AU  - Nikolić, Maria Vesna
AU  - Stamenović, Bojana
PY  - 2007
UR  - https://dais.sanu.ac.rs/123456789/312
AB  - Poster presented at the 14th International Conference on Photoacoustic and Photothermal Phenomena, Cairo, Egypt, January 6-9, 2007
T1  - Thermal diffusivity of sintered 12CaO×7AI2O3
UR  - https://hdl.handle.net/21.15107/rcub_dais_312
ER  - 

@conference{
author = "Nikolić, Pantelija M. and Luković, Danijela and Savić, Slavica M. and Milovanović, A. M. and Đukić, S. R. and Nikolić, Maria Vesna and Stamenović, Bojana",
year = "2007",
abstract = "Poster presented at the 14th International Conference on Photoacoustic and Photothermal Phenomena, Cairo, Egypt, January 6-9, 2007",
title = "Thermal diffusivity of sintered 12CaO×7AI2O3",
url = "https://hdl.handle.net/21.15107/rcub_dais_312"
}

Nikolić, P. M., Luković, D., Savić, S. M., Milovanović, A. M., Đukić, S. R., Nikolić, M. V.,& Stamenović, B.. (2007). Thermal diffusivity of sintered 12CaO×7AI2O3. .
https://hdl.handle.net/21.15107/rcub_dais_312

Nikolić PM, Luković D, Savić SM, Milovanović AM, Đukić SR, Nikolić MV, Stamenović B. Thermal diffusivity of sintered 12CaO×7AI2O3. 2007;.
https://hdl.handle.net/21.15107/rcub_dais_312 .

Nikolić, Pantelija M., Luković, Danijela, Savić, Slavica M., Milovanović, A. M., Đukić, S. R., Nikolić, Maria Vesna, Stamenović, Bojana, "Thermal diffusivity of sintered 12CaO×7AI2O3" (2007),
https://hdl.handle.net/21.15107/rcub_dais_312 .

TY  - CONF
AU  - Nikolić, Maria Vesna
AU  - Savić, Slavica M.
AU  - Aleksić, Obrad S.
AU  - Paraskevopoulos, Konstantinos M.
AU  - Zorba, Triantafyllia T.
AU  - Blagojević, Vladimir D.
AU  - Nikolić, Pantelija M.
PY  - 2007
UR  - https://dais.sanu.ac.rs/123456789/310
AB  - Poster presented at the 10th International Conference and Exhibition of the European Ceramic Society, Berlin, June 17-21, 2007
T1  - Changes of Structural, Optical and Electrical Properties of Nickel-Manganite Ceramics Induced by Additional Mechanical Activation
UR  - https://hdl.handle.net/21.15107/rcub_dais_310
ER  - 

@conference{
author = "Nikolić, Maria Vesna and Savić, Slavica M. and Aleksić, Obrad S. and Paraskevopoulos, Konstantinos M. and Zorba, Triantafyllia T. and Blagojević, Vladimir D. and Nikolić, Pantelija M.",
year = "2007",
abstract = "Poster presented at the 10th International Conference and Exhibition of the European Ceramic Society, Berlin, June 17-21, 2007",
title = "Changes of Structural, Optical and Electrical Properties of Nickel-Manganite Ceramics Induced by Additional Mechanical Activation",
url = "https://hdl.handle.net/21.15107/rcub_dais_310"
}

Nikolić, M. V., Savić, S. M., Aleksić, O. S., Paraskevopoulos, K. M., Zorba, T. T., Blagojević, V. D.,& Nikolić, P. M.. (2007). Changes of Structural, Optical and Electrical Properties of Nickel-Manganite Ceramics Induced by Additional Mechanical Activation. .
https://hdl.handle.net/21.15107/rcub_dais_310

Nikolić MV, Savić SM, Aleksić OS, Paraskevopoulos KM, Zorba TT, Blagojević VD, Nikolić PM. Changes of Structural, Optical and Electrical Properties of Nickel-Manganite Ceramics Induced by Additional Mechanical Activation. 2007;.
https://hdl.handle.net/21.15107/rcub_dais_310 .

Nikolić, Maria Vesna, Savić, Slavica M., Aleksić, Obrad S., Paraskevopoulos, Konstantinos M., Zorba, Triantafyllia T., Blagojević, Vladimir D., Nikolić, Pantelija M., "Changes of Structural, Optical and Electrical Properties of Nickel-Manganite Ceramics Induced by Additional Mechanical Activation" (2007),
https://hdl.handle.net/21.15107/rcub_dais_310 .

TY  - CONF
AU  - Nikolić, Pantelija M.
AU  - Luković, Danijela
AU  - Nikolić, Maria Vesna
AU  - Đurić, S.
AU  - Savić, Slavica M.
AU  - Milovanović, A. M.
AU  - Đukić, S. R.
AU  - Stamenović, Bojana
PY  - 2007
UR  - https://dais.sanu.ac.rs/123456789/311
AB  - Poster presented at the 14th International Conference on Photoacoustic and Photothermal Phenomena, Cairo, Egypt, January 6-9, 2007
T1  - Photoacoustic Characterization of Natural Mineral Pyrite (FeS2)
UR  - https://hdl.handle.net/21.15107/rcub_dais_311
ER  - 

@conference{
author = "Nikolić, Pantelija M. and Luković, Danijela and Nikolić, Maria Vesna and Đurić, S. and Savić, Slavica M. and Milovanović, A. M. and Đukić, S. R. and Stamenović, Bojana",
year = "2007",
abstract = "Poster presented at the 14th International Conference on Photoacoustic and Photothermal Phenomena, Cairo, Egypt, January 6-9, 2007",
title = "Photoacoustic Characterization of Natural Mineral Pyrite (FeS2)",
url = "https://hdl.handle.net/21.15107/rcub_dais_311"
}

Nikolić, P. M., Luković, D., Nikolić, M. V., Đurić, S., Savić, S. M., Milovanović, A. M., Đukić, S. R.,& Stamenović, B.. (2007). Photoacoustic Characterization of Natural Mineral Pyrite (FeS2). .
https://hdl.handle.net/21.15107/rcub_dais_311

Nikolić PM, Luković D, Nikolić MV, Đurić S, Savić SM, Milovanović AM, Đukić SR, Stamenović B. Photoacoustic Characterization of Natural Mineral Pyrite (FeS2). 2007;.
https://hdl.handle.net/21.15107/rcub_dais_311 .

Nikolić, Pantelija M., Luković, Danijela, Nikolić, Maria Vesna, Đurić, S., Savić, Slavica M., Milovanović, A. M., Đukić, S. R., Stamenović, Bojana, "Photoacoustic Characterization of Natural Mineral Pyrite (FeS2)" (2007),
https://hdl.handle.net/21.15107/rcub_dais_311 .

TY  - CONF
AU  - Aleksić, Obrad S.
AU  - Savić, Slavica
AU  - Luković, Miloljub D.
AU  - Radulović, Katarina
AU  - Lukić, Lazar S.
PY  - 2006
UR  - https://dais.sanu.ac.rs/123456789/9556
AB  - An investigation path starting from (Mn,Ni,Co,Fe)3O4 nanometric powder preparation, NTC thick-film characterization, realization and optimization of new planar thermistor geometries to custom design thermistors and their application for temperature and volume airflow sensors was recently determined. The aim was to make custom designed segmented NTC thermistors printed and sintered on alumina. Two types of volume airflow sensors were formed: indirectly heated and self-heated. A pair of segmented thermistors was placed in an air guide and connected to differential branches of the Wheatstone bridge. A heater was placed in the middle between the thermistors for the indirectly heated type, while for the self-heated type the same thermistors were self-heated by a constant current source. First the thermistor responses vs. the airflow (calibration curves) were measured, and then thermistor responses in time (inertia) to fast airflow changes from the minimum to the maximum. The results obtained could be applied in air conditioning for air guide flow regulation.
C3  - Recent Developments in Advanced Materials and Processe
T1  - Segmented thermistors printed by NTC nanometric paste and applied in volume air-flow sensors
SP  - 247
EP  - 252
VL  - 518
DO  - 10.4028/www.scientific.net/MSF.518.247
UR  - https://hdl.handle.net/21.15107/rcub_dais_9556
ER  - 

@conference{
author = "Aleksić, Obrad S. and Savić, Slavica and Luković, Miloljub D. and Radulović, Katarina and Lukić, Lazar S.",
year = "2006",
abstract = "An investigation path starting from (Mn,Ni,Co,Fe)3O4 nanometric powder preparation, NTC thick-film characterization, realization and optimization of new planar thermistor geometries to custom design thermistors and their application for temperature and volume airflow sensors was recently determined. The aim was to make custom designed segmented NTC thermistors printed and sintered on alumina. Two types of volume airflow sensors were formed: indirectly heated and self-heated. A pair of segmented thermistors was placed in an air guide and connected to differential branches of the Wheatstone bridge. A heater was placed in the middle between the thermistors for the indirectly heated type, while for the self-heated type the same thermistors were self-heated by a constant current source. First the thermistor responses vs. the airflow (calibration curves) were measured, and then thermistor responses in time (inertia) to fast airflow changes from the minimum to the maximum. The results obtained could be applied in air conditioning for air guide flow regulation.",
journal = "Recent Developments in Advanced Materials and Processe",
title = "Segmented thermistors printed by NTC nanometric paste and applied in volume air-flow sensors",
pages = "247-252",
volume = "518",
doi = "10.4028/www.scientific.net/MSF.518.247",
url = "https://hdl.handle.net/21.15107/rcub_dais_9556"
}

Aleksić, O. S., Savić, S., Luković, M. D., Radulović, K.,& Lukić, L. S.. (2006). Segmented thermistors printed by NTC nanometric paste and applied in volume air-flow sensors. in Recent Developments in Advanced Materials and Processe, 518, 247-252.
https://doi.org/10.4028/www.scientific.net/MSF.518.247
https://hdl.handle.net/21.15107/rcub_dais_9556

Aleksić OS, Savić S, Luković MD, Radulović K, Lukić LS. Segmented thermistors printed by NTC nanometric paste and applied in volume air-flow sensors. in Recent Developments in Advanced Materials and Processe. 2006;518:247-252.
doi:10.4028/www.scientific.net/MSF.518.247
https://hdl.handle.net/21.15107/rcub_dais_9556 .

Aleksić, Obrad S., Savić, Slavica, Luković, Miloljub D., Radulović, Katarina, Lukić, Lazar S., "Segmented thermistors printed by NTC nanometric paste and applied in volume air-flow sensors" in Recent Developments in Advanced Materials and Processe, 518 (2006):247-252,
https://doi.org/10.4028/www.scientific.net/MSF.518.247 .,
https://hdl.handle.net/21.15107/rcub_dais_9556 .