Optimization and Application of NTC Thick Film Segmented Thermistors
Samo za registrovane korisnike
2013
Autori
Nikolić, Maria VesnaAleksić, Obrad S.
Radojčić, B. M.
Luković, Miloljub D.
Nikolić, N.
Đurić, Zorka Ž.
Konferencijski prilog (Objavljena verzija)
Metapodaci
Prikaz svih podataka o dokumentuApstrakt
NTC thermistor paste for printing thermal sensors on alumina was formed of very fine Ni0.5Cu0.2Zn1.0Mn1.3O4 thermistor powder obtained by a combined mechanical activation/thermal treatment process, organic vehicle and glass frit. Sheet resistivity was measured using an R-test matrix and it was much lower than the value determined for pure nickel manganite thermistors. The thermistor exponential coefficient was calculated from the R[ diagram measured in the temperature range-30 to +120°C in a climatic chamber. Thick film segmented thermistors with reduced dimensions (optimized construction) were printed sequentially layer by layer, dried and fired at 850°C/10 min in air. Electrodes were printed of PdAg conductive and solderable paste. The samples obtained were characterized by electrical and thermal measurements. The obtained NTC segmented thermistors with reduced dimensions were applied in a thermal sensor for water flow in the water mains. It contained a cold thermistor for measuring ...input water temperature and a self-heating thermistor for measuring the dependence of water current on water flow rate at a set input voltage power. Initial measurements show that the thermal sensor system requires a low input voltage power making it much easier and safer for operation.
Ključne reči:
Zn doping / nickel manganite / thick films / NTC thermistors / thermal sensorsIzvor:
Materials and Applications for Sensors and Transducers II: Proceedings of the 2nd International Conference, 2013, -494Izdavač:
- Zurich : Trans Tech Publications Inc.
Finansiranje / projekti:
- 0-3D nanostrukture za primenu u elektronici i obnovljivim izvorima energije: sinteza, karakterizacija i procesiranje (RS-MESTD-Integrated and Interdisciplinary Research (IIR or III)-45007)
DOI: 10.4028/www.scientific.net/KEM.543.491
ISBN: 978-3-03785-616-1
ISSN: 1662-9795
WoS: 000319023100119
Scopus: 2-s2.0-84876385906
Institucija/grupa
Институт техничких наука САНУ / Institute of Technical Sciences of SASATY - CONF AU - Nikolić, Maria Vesna AU - Aleksić, Obrad S. AU - Radojčić, B. M. AU - Luković, Miloljub D. AU - Nikolić, N. AU - Đurić, Zorka Ž. PY - 2013 UR - https://dais.sanu.ac.rs/123456789/678 AB - NTC thermistor paste for printing thermal sensors on alumina was formed of very fine Ni0.5Cu0.2Zn1.0Mn1.3O4 thermistor powder obtained by a combined mechanical activation/thermal treatment process, organic vehicle and glass frit. Sheet resistivity was measured using an R-test matrix and it was much lower than the value determined for pure nickel manganite thermistors. The thermistor exponential coefficient was calculated from the R[ diagram measured in the temperature range-30 to +120°C in a climatic chamber. Thick film segmented thermistors with reduced dimensions (optimized construction) were printed sequentially layer by layer, dried and fired at 850°C/10 min in air. Electrodes were printed of PdAg conductive and solderable paste. The samples obtained were characterized by electrical and thermal measurements. The obtained NTC segmented thermistors with reduced dimensions were applied in a thermal sensor for water flow in the water mains. It contained a cold thermistor for measuring input water temperature and a self-heating thermistor for measuring the dependence of water current on water flow rate at a set input voltage power. Initial measurements show that the thermal sensor system requires a low input voltage power making it much easier and safer for operation. PB - Zurich : Trans Tech Publications Inc. C3 - Materials and Applications for Sensors and Transducers II: Proceedings of the 2nd International Conference T1 - Optimization and Application of NTC Thick Film Segmented Thermistors EP - 494 DO - 10.4028/www.scientific.net/KEM.543.491 UR - https://hdl.handle.net/21.15107/rcub_dais_678 ER -
@conference{ author = "Nikolić, Maria Vesna and Aleksić, Obrad S. and Radojčić, B. M. and Luković, Miloljub D. and Nikolić, N. and Đurić, Zorka Ž.", year = "2013", abstract = "NTC thermistor paste for printing thermal sensors on alumina was formed of very fine Ni0.5Cu0.2Zn1.0Mn1.3O4 thermistor powder obtained by a combined mechanical activation/thermal treatment process, organic vehicle and glass frit. Sheet resistivity was measured using an R-test matrix and it was much lower than the value determined for pure nickel manganite thermistors. The thermistor exponential coefficient was calculated from the R[ diagram measured in the temperature range-30 to +120°C in a climatic chamber. Thick film segmented thermistors with reduced dimensions (optimized construction) were printed sequentially layer by layer, dried and fired at 850°C/10 min in air. Electrodes were printed of PdAg conductive and solderable paste. The samples obtained were characterized by electrical and thermal measurements. The obtained NTC segmented thermistors with reduced dimensions were applied in a thermal sensor for water flow in the water mains. It contained a cold thermistor for measuring input water temperature and a self-heating thermistor for measuring the dependence of water current on water flow rate at a set input voltage power. Initial measurements show that the thermal sensor system requires a low input voltage power making it much easier and safer for operation.", publisher = "Zurich : Trans Tech Publications Inc.", journal = "Materials and Applications for Sensors and Transducers II: Proceedings of the 2nd International Conference", title = "Optimization and Application of NTC Thick Film Segmented Thermistors", pages = "494", doi = "10.4028/www.scientific.net/KEM.543.491", url = "https://hdl.handle.net/21.15107/rcub_dais_678" }
Nikolić, M. V., Aleksić, O. S., Radojčić, B. M., Luković, M. D., Nikolić, N.,& Đurić, Z. Ž.. (2013). Optimization and Application of NTC Thick Film Segmented Thermistors. in Materials and Applications for Sensors and Transducers II: Proceedings of the 2nd International Conference Zurich : Trans Tech Publications Inc... https://doi.org/10.4028/www.scientific.net/KEM.543.491 https://hdl.handle.net/21.15107/rcub_dais_678
Nikolić MV, Aleksić OS, Radojčić BM, Luković MD, Nikolić N, Đurić ZŽ. Optimization and Application of NTC Thick Film Segmented Thermistors. in Materials and Applications for Sensors and Transducers II: Proceedings of the 2nd International Conference. 2013;:null-494. doi:10.4028/www.scientific.net/KEM.543.491 https://hdl.handle.net/21.15107/rcub_dais_678 .
Nikolić, Maria Vesna, Aleksić, Obrad S., Radojčić, B. M., Luković, Miloljub D., Nikolić, N., Đurić, Zorka Ž., "Optimization and Application of NTC Thick Film Segmented Thermistors" in Materials and Applications for Sensors and Transducers II: Proceedings of the 2nd International Conference (2013), https://doi.org/10.4028/www.scientific.net/KEM.543.491 ., https://hdl.handle.net/21.15107/rcub_dais_678 .