Supercritical CO2 assisted deposition of MAPbBr3 perovskite onto TiO2 nanotubes
Конференцијски прилог (Објављена верзија)
Метаподаци
Приказ свих података о документуАпстракт
Supercritical carbon dioxide (sCO2) is an ideal low-temperature cosolvent for perovskite deposition due to its relatively low critical point (31.2 °C, 73.8 bar), no surface tension, liquid-like density, gas-like viscosity, and diffusivity. It enables faster mass transfer which allows penetration of crystals in nanoporous structure. The study investigates the influence of time of deposition of perovskite assisted with supercritical carbon dioxide on the filling of nanotubes. Perovskite solar cell technology has been developed so fast due to several factors including a tunable band gap, high absorption coefficient, and low-cost fabrication. The quality of the perovskite film is important for the high efficiency of perovskite solar cells. Perovskite precursors are usually deposited from the solution onto a substrate using spin-coating followed by post-deposition treatments, but often it results in low-quality films that cannot provide good photovoltaic performances. Deposition of perovski...te in the presence of sCO2 is a promising method for the formation of high-quality perovskite layers. In this work, methylammonium lead bromide perovskite (MAPbBr3) was deposited on TiO2 nanotubes from the solution in dimethylformamide (DMF) by application of sCO2 at 35 °C and 200 bar for 1 h, and 3 h. FESEM results show that TiO2 nanotubes were filled with perovskite material in both cases. The diffuse reflectance spectroscopy measurement of samples proved that the absorption edge of prepared TiO2 nanotubes/MAPbBr3 was extended to the visible range. Measurement of I-V characteristics showed that the sample made for 3 h had a higher value of current than the sample prepared for 1 h. The application of sCO2 during the deposition of perovskite has enabled the preparation of a photodiode with a better contact between TiO2 nanotubes and perovskite which is important for the future development of solar cells.
Кључне речи:
supercritical carbon dioxide / perovskites / TiO2 nanotubes / depositionИзвор:
Program and The Book of abstracts / Twenty-third Annual Conference YUCOMAT 2022 & Twelfth World Round Table Conference on Sintering XII WRTCS 2022, Herceg Novi, Montenegro, August 29 - September 2, 2022, 2022, 73-73Издавач:
- Belgrade : Materials Research Society of Serbia
Финансирање / пројекти:
- Министарство науке, технолошког развоја и иновација Републике Србије, институционално финансирање - 200175 (Институт техничких наука САНУ, Београд) (RS-MESTD-inst-2020-200175)
Институција/група
Институт техничких наука САНУ / Institute of Technical Sciences of SASATY - CONF AU - Stefanović, Milica AU - Lukić, Ivana AU - Vujančević, Jelena AU - Petrović, Rada AU - Janaćković, Đorđe PY - 2022 UR - https://dais.sanu.ac.rs/123456789/13591 AB - Supercritical carbon dioxide (sCO2) is an ideal low-temperature cosolvent for perovskite deposition due to its relatively low critical point (31.2 °C, 73.8 bar), no surface tension, liquid-like density, gas-like viscosity, and diffusivity. It enables faster mass transfer which allows penetration of crystals in nanoporous structure. The study investigates the influence of time of deposition of perovskite assisted with supercritical carbon dioxide on the filling of nanotubes. Perovskite solar cell technology has been developed so fast due to several factors including a tunable band gap, high absorption coefficient, and low-cost fabrication. The quality of the perovskite film is important for the high efficiency of perovskite solar cells. Perovskite precursors are usually deposited from the solution onto a substrate using spin-coating followed by post-deposition treatments, but often it results in low-quality films that cannot provide good photovoltaic performances. Deposition of perovskite in the presence of sCO2 is a promising method for the formation of high-quality perovskite layers. In this work, methylammonium lead bromide perovskite (MAPbBr3) was deposited on TiO2 nanotubes from the solution in dimethylformamide (DMF) by application of sCO2 at 35 °C and 200 bar for 1 h, and 3 h. FESEM results show that TiO2 nanotubes were filled with perovskite material in both cases. The diffuse reflectance spectroscopy measurement of samples proved that the absorption edge of prepared TiO2 nanotubes/MAPbBr3 was extended to the visible range. Measurement of I-V characteristics showed that the sample made for 3 h had a higher value of current than the sample prepared for 1 h. The application of sCO2 during the deposition of perovskite has enabled the preparation of a photodiode with a better contact between TiO2 nanotubes and perovskite which is important for the future development of solar cells. PB - Belgrade : Materials Research Society of Serbia C3 - Program and The Book of abstracts / Twenty-third Annual Conference YUCOMAT 2022 & Twelfth World Round Table Conference on Sintering XII WRTCS 2022, Herceg Novi, Montenegro, August 29 - September 2, 2022 T1 - Supercritical CO2 assisted deposition of MAPbBr3 perovskite onto TiO2 nanotubes SP - 73 EP - 73 UR - https://hdl.handle.net/21.15107/rcub_dais_13591 ER -
@conference{ author = "Stefanović, Milica and Lukić, Ivana and Vujančević, Jelena and Petrović, Rada and Janaćković, Đorđe", year = "2022", abstract = "Supercritical carbon dioxide (sCO2) is an ideal low-temperature cosolvent for perovskite deposition due to its relatively low critical point (31.2 °C, 73.8 bar), no surface tension, liquid-like density, gas-like viscosity, and diffusivity. It enables faster mass transfer which allows penetration of crystals in nanoporous structure. The study investigates the influence of time of deposition of perovskite assisted with supercritical carbon dioxide on the filling of nanotubes. Perovskite solar cell technology has been developed so fast due to several factors including a tunable band gap, high absorption coefficient, and low-cost fabrication. The quality of the perovskite film is important for the high efficiency of perovskite solar cells. Perovskite precursors are usually deposited from the solution onto a substrate using spin-coating followed by post-deposition treatments, but often it results in low-quality films that cannot provide good photovoltaic performances. Deposition of perovskite in the presence of sCO2 is a promising method for the formation of high-quality perovskite layers. In this work, methylammonium lead bromide perovskite (MAPbBr3) was deposited on TiO2 nanotubes from the solution in dimethylformamide (DMF) by application of sCO2 at 35 °C and 200 bar for 1 h, and 3 h. FESEM results show that TiO2 nanotubes were filled with perovskite material in both cases. The diffuse reflectance spectroscopy measurement of samples proved that the absorption edge of prepared TiO2 nanotubes/MAPbBr3 was extended to the visible range. Measurement of I-V characteristics showed that the sample made for 3 h had a higher value of current than the sample prepared for 1 h. The application of sCO2 during the deposition of perovskite has enabled the preparation of a photodiode with a better contact between TiO2 nanotubes and perovskite which is important for the future development of solar cells.", publisher = "Belgrade : Materials Research Society of Serbia", journal = "Program and The Book of abstracts / Twenty-third Annual Conference YUCOMAT 2022 & Twelfth World Round Table Conference on Sintering XII WRTCS 2022, Herceg Novi, Montenegro, August 29 - September 2, 2022", title = "Supercritical CO2 assisted deposition of MAPbBr3 perovskite onto TiO2 nanotubes", pages = "73-73", url = "https://hdl.handle.net/21.15107/rcub_dais_13591" }
Stefanović, M., Lukić, I., Vujančević, J., Petrović, R.,& Janaćković, Đ.. (2022). Supercritical CO2 assisted deposition of MAPbBr3 perovskite onto TiO2 nanotubes. in Program and The Book of abstracts / Twenty-third Annual Conference YUCOMAT 2022 & Twelfth World Round Table Conference on Sintering XII WRTCS 2022, Herceg Novi, Montenegro, August 29 - September 2, 2022 Belgrade : Materials Research Society of Serbia., 73-73. https://hdl.handle.net/21.15107/rcub_dais_13591
Stefanović M, Lukić I, Vujančević J, Petrović R, Janaćković Đ. Supercritical CO2 assisted deposition of MAPbBr3 perovskite onto TiO2 nanotubes. in Program and The Book of abstracts / Twenty-third Annual Conference YUCOMAT 2022 & Twelfth World Round Table Conference on Sintering XII WRTCS 2022, Herceg Novi, Montenegro, August 29 - September 2, 2022. 2022;:73-73. https://hdl.handle.net/21.15107/rcub_dais_13591 .
Stefanović, Milica, Lukić, Ivana, Vujančević, Jelena, Petrović, Rada, Janaćković, Đorđe, "Supercritical CO2 assisted deposition of MAPbBr3 perovskite onto TiO2 nanotubes" in Program and The Book of abstracts / Twenty-third Annual Conference YUCOMAT 2022 & Twelfth World Round Table Conference on Sintering XII WRTCS 2022, Herceg Novi, Montenegro, August 29 - September 2, 2022 (2022):73-73, https://hdl.handle.net/21.15107/rcub_dais_13591 .